The skid control ECU (brake actuator assembly) receives signals from the ECM, yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 and steering angle sensor (spiral with sensor cable sub-assembly) via CAN communication.
*1: w/o Airbag System
*2: w/ Airbag System
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| U0073 | Either of the following is detected:
1.
A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession. (Sent signals cannot be received.) 2.
When the +BS terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 1 second or more. 3.
When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds. -
The condition that a delay in receiving data from the yaw rate sensor and steering angle sensor occurs more than once within 5 seconds. |
CAN communication system |
| U0100 | When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more. | ·
CAN communication system ·
Skid control ECU (Brake actuator assembly) ·
ECM |
| U0124 | Either of the following is detected:
1.
When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received for 1 second or more. 2.
When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds. -
The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds. |
·
CAN communication system ·
Skid control ECU (Brake actuator assembly) ·
Acceleration sensor (Yaw rate sensor)*1 ·
Acceleration sensor (Airbag ECU assembly)*2 |
| U0126 | Either of the following is detected:
1.
When the +BS terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more. 2.
When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession. -
The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds. |
·
CAN communication system ·
Skid control ECU (Brake actuator assembly) ·
Steering angle sensor (Spiral with sensor cable sub-assembly) |
*1: w/o Airbag System
*2: w/ Airbag System
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| EFI Communication Open | ECM communication open detection / Error or Normal | Normal | Error: Momentary interruption |
| Yaw Rate Open | Yaw rate sensor open detection / Error or Normal | Normal | Error: Momentary interruption |
| Deceleration Open | Acceleration sensor open detection / Error or Normal | Normal | Error: Momentary interruption |
| Steering Open | Steering angle sensor open detection / Error or Normal | Normal | Error: Momentary interruption |
| Result | Proceed to |
|---|---|
| There is a constant open circuit | A |
| There are no momentary interruptions | B |
| There are momentary interruptions | C |
Perform the above inspection before removing the sensor and connector.
A
B
C
Turn the ignition switch off.
Check if each sensor or ECM connector is securely connected.
Each connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Record the output DTCs (for ABS system and/or CAN communication system) (Click here Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEARfor ABS system, or Click here Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEMfor CAN communication system).
If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS system) after the CAN communication system returns to normal.
| Result | Proceed to |
|---|---|
| DTC (relating to CAN communication system) is output | A |
| DTC (relating to ABS system) is output | B |
| DTC is not output | C |
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CHECK FOR INTERMITTENT PROBLEMS).
Check that there is no momentary interruption.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.
Check that no CAN communication system DTC is output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
If ABS system DTCs are output, record them (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (relating to ABS system) | B |
| DTC is output (relating to CAN communication system) | C |
The CAN communication system must be normal when repairing each sensor DTC (for ABS system).
A
B
C