Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C0273/13  Open in ABS Motor Relay Circuit  C0274/14  Short to B+ in ABS Motor Relay Circuit  


DESCRIPTION

While the ABS is operating, the skid control ECU turns the ABS MTR relay on and activates the pump motor in the brake actuator.

These codes may be stored if the motor relay (BM) voltage becomes lower than a specified level due to insufficient output from the battery or alternator.

DTC Code DTC Detection Condition Trouble Area
C0273/13 When either of the following is detected:
1.

IG1 terminal voltage is 9.5 to 18.5 V during the initial check or ABS operation, and when the relay is ON, the relay contact is OFF for 0.2 seconds or more.

2.

IG1 terminal voltage is 9.5 V or less during the initial check or ABS operation, and when the relay is ON, the relay contact is not ON for 0.2 seconds or more.


·

ABS MTR relay

·

ABS MTR relay circuit

·

Brake actuator assembly

·

Skid control ECU


C0274/14 When either of the following is detected:
1.

When the relay is OFF, the relay contact is ON for 4 seconds or more.

2.

When the relay is OFF, an open in the MT terminal continues for 4 seconds or more.


·

ABS MTR relay

·

ABS MTR relay circuit

·

Brake actuator assembly

·

Skid control ECU



WIRING DIAGRAM

C374973E01
0.865,0.969 1.177,1.167 0.313,0.198 10 false BM 1.229,0.708 1.542,0.906 0.313,0.198 10 false 2 2.25,0.698 2.49,0.906 0.24,0.208 10 false 3 2.25,1.094 2.448,1.302 0.198,0.208 10 false 2 3.167,0.708 3.375,0.927 0.208,0.219 10 false 5 3.156,1.094 3.354,1.302 0.198,0.208 10 false 1 2.458,1.594 3.271,1.802 0.813,0.208 10 false ABS MTR 4.198,1.698 4.99,1.917 0.792,0.219 10 false ABS NO. 1 6.115,1.208 6.427,1.406 0.313,0.198 10 false MR 5.781,0.99 6.021,1.198 0.24,0.208 10 false 8 5.708,1.219 6.052,1.438 0.344,0.219 10 false A50 5.74,1.979 6.052,2.177 0.313,0.198 10 false 21 6.125,2.188 6.438,2.385 0.313,0.198 10 false R+ 6.115,3.167 6.427,3.365 0.313,0.198 10 false MT 5.771,2.948 6.083,3.146 0.313,0.198 10 false 3 5.698,3.177 6.052,3.385 0.354,0.208 10 false A47 3.719,3.719 4.604,3.958 0.885,0.24 10 false from Battery 1.219,3.063 1.531,3.26 0.313,0.198 10 false 3 0.906,3.313 1.219,3.51 0.313,0.198 10 false MT 1.219,5.031 1.531,5.229 0.313,0.198 10 false 1 0.781,5.302 1.26,5.552 0.479,0.25 10 false GND 0.24,6.125 0.552,6.323 0.313,0.198 10 false R2 0.24,6.302 1.469,6.583 1.229,0.281 10 false Brake Actuator 5.938,6.313 7.083,6.552 1.146,0.24 10 false Skid Control ECU 5.698,2.198 6.042,2.417 0.344,0.219 10 false A50

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT ABS MOTOR RELAY (ABS MTR)
a.
C144829E13
0.138,0.102 0.344,0.295 0.206,0.193 10 *1

Remove the ABS MTR relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Apply the battery voltage between terminals 1 and 2 Below 1 Ω

Text in Illustration
*1 ABS MTR Relay



Result:
Proceed to
OK
NG



OK

2.INSPECT ENGINE ROOM RELAY BLOCK (POWER SOURCE TERMINAL)

NG

REPLACE ABS MOTOR RELAY (ABS MTR)

2.INSPECT ENGINE ROOM RELAY BLOCK (POWER SOURCE TERMINAL)
a.
C375221E01
0.177,0.104 0.49,0.302 0.313,0.198 10 false *1 2.469,1.365 2.781,1.563 0.313,0.198 10 false *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ABS MTR relay terminal 5 - Body ground Always 11 to 14 V

Text in Illustration
*1 Engine Room Relay Block
*2 ABS MTR Relay



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.INSPECT BRAKE ACTUATOR ASSEMBLY
a.
C215677E06
2.49,1.604 2.49,0.813 true 2.844,2.75 2.844,1.969 true 0.083,0.052 0.354,0.271 0.271,0.219 10 false *1 2.76,2.781 2.99,2.958 0.229,0.177 10 false MT 2.385,0.594 2.625,0.771 0.24,0.177 10 false BM

Disconnect the brake actuator connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM) - 3 (MT) Always 31.3 to 34.7 Ω
3 (MT) - Body ground Always 10 kΩ or higher

Text in Illustration
*1 Component without harness connected
(Brake Actuator)



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR - ENGINE ROOM RELAY BLOCK)

NG

REPLACE BRAKE ACTUATOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR - ENGINE ROOM RELAY BLOCK)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-2 (BM) - ABS MTR relay terminal 3 Always Below 1 Ω
R2-2 (BM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE ACTUATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE ACTUATOR)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-3 (MT) - R2-3(MT) Always Below 1 Ω
A47-3 (MT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-8 (MR) - ABS MTR relay terminal 1 Always Below 1 Ω
A50-8 (MR) - Body ground Always 10 kΩ or higher
A50-21 (R+) - ABS MTR relay terminal 2 Always Below 1 Ω
A50-21 (R+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Install the ABS MTR relay.


c.

Reconnect the skid control ECU and brake actuator connectors.



e.

Start the engine.


f.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


g.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

HINT:

Reinstall the relays, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


Result:
Result Proceed to
DTCs (C0273/13 and/or C0274/14) are not output A
DTCs (C0273/13 and/or C0274/14) are output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU and brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU and brake actuator assembly, inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B

REPLACE SKID CONTROL ECU