Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C1266/66  Exhaust Retarder Prevention Signal Circuit  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
C1266/66 When vehicle speed is 6 km/h (4 mph) or more, an open or short circuit in the EXO signal circuit continues for 0.3 seconds or more.
·

ECU-B NO. 8 fuse*2

·

EXO circuit

·

ECM*1

·

Stop light control ECU*2

·

Skid control ECU



*1: for N04C-UH

*2: for 1HZ


WIRING DIAGRAM

C377026E01
0.146,0.531 1.01,0.802 0.865,0.271 10 false from Battery 1.656,0.698 2.604,0.979 0.948,0.281 10 false ECU-B NO. 8 2.76,1.438 3.146,1.646 0.385,0.208 10 false A73 2.75,1.625 4.51,1.875 1.76,0.25 10 false Stop Light Control ECU*2 2.604,0.417 2.823,0.656 0.219,0.24 10 false 6 2.615,0.833 2.865,1.042 0.25,0.208 10 false 8 2.833,0.531 3.219,0.74 0.385,0.208 10 false +B 2.833,0.958 3.24,1.177 0.406,0.219 10 false GND 3.885,0.729 4.271,0.938 0.385,0.208 10 false ACC 4.302,0.583 4.542,0.792 0.24,0.208 10 false 9 5.167,1.51 5.552,1.719 0.385,0.208 10 false *2 5.823,2.813 6.302,3.094 0.479,0.281 10 false EXO 5.531,2.938 5.792,3.156 0.26,0.219 10 false 18 5.583,3.958 5.969,4.167 0.385,0.208 10 false A50 5.583,4.146 6.854,4.375 1.271,0.229 10 false Skid Control ECU 3.51,2.969 3.896,3.177 0.385,0.208 10 false *1 1.604,2.677 1.99,2.885 0.385,0.208 10 false 30 1.177,2.823 1.667,3.063 0.49,0.24 10 false ABS 0.667,4 1.052,4.208 0.385,0.208 10 false A52 0.667,4.177 1.323,4.427 0.656,0.25 10 false ECM*1 2.354,3.917 3.448,4.146 1.094,0.229 10 false *1: for N04C-UH 2.375,4.25 3.271,4.448 0.896,0.198 10 false *2: for 1HZ

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM OR STOP LIGHT CONTROL ECU)
a.

Disconnect the ECM*1 or stop light control ECU*2 connector.

*1: for N04C-UH

*2: for 1HZ



b.

Disconnect the skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-18 (EXO) - A52-30 (ABS)*1
A50-18 (EXO) - A73-9 (ACC)*2
Always Below 1 Ω
A50-18 (EXO) - Body ground Always 10 kΩ or higher


*1: for N04C-UH

*2: for 1HZ



Result:
Result Proceed to
OK (for N04C-UH) A
OK (for 1HZ) B
NG C



A

2.INSPECT ECM (ECU OUTPUT)

B

3.INSPECT STOP LIGHT CONTROL ECU (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (ECU OUTPUT)
a.

Turn the ignition switch off.


b.
E401082E01
1.052,1.969 1.438,2.188 0.385,0.219 2.042,4.115 1.615,3.125 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 1.125,2 1.438,2.198 0.313,0.198 10 false A52 1.833,4.198 2.625,4.417 0.792,0.219 10 false 30 (ABS)

Reconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A52-30 (ABS) - Body ground Ignition switch ON 11 to 14 V

Text in Illustration
*a Component with harness connected
(ECM)



Result:
Result Proceed to
NG A
OK B



A

REPLACE ECM

B

5.INSPECT SKID CONTROL ECU (ECU INPUT)
3.INSPECT STOP LIGHT CONTROL ECU (POWER SOURCE CIRCUIT)
a.
E173014E17
1.5,0.24 1.906,0.469 0.406,0.229 1.406,1.323 1.406,1.677 true 1.823,1.323 1.823,1.677 true 0.156,0.146 0.417,0.344 0.26,0.198 10 false *a 1.25,1.698 1.469,1.875 0.219,0.177 10 false +B 1.667,1.698 2.01,1.875 0.344,0.177 10 false GND 1.583,0.271 1.917,0.5 0.333,0.229 10 false A73

Turn the ignition switch off.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A73-6 (+B) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A73-8 (GND) - Body ground Always Below 1 Ω

Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control ECU)



Result:
Proceed to
OK
NG



OK

4.INSPECT STOP LIGHT CONTROL ECU (ECU OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STOP LIGHT CONTROL ECU (ECU OUTPUT)
a.
E173013E21
1.51,0.813 1.906,1.031 0.396,0.219 0.969,2.698 1.135,2.698 1.135,2.698 1.396,2.052 true 1.656,2.042 2.063,2.708 2.063,2.708 2.25,2.708 true 0.198,0.135 0.385,0.323 0.188,0.188 10 false *a 1.594,0.833 1.979,1.031 0.385,0.198 10 false A73 0.594,2.615 0.969,2.833 0.375,0.219 10 false ACC 2.313,2.625 2.802,2.833 0.49,0.208 10 false GND

Turn the ignition switch off.


b.

Reconnect the stop light control ECU connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A73-9 (ACC) - A73-8 (GND) Ignition switch ON 11 to 14 V

Text in Illustration
*a Component with harness connected
(Stop Light Control ECU)



Result:
Proceed to
OK
NG



OK

5.INSPECT SKID CONTROL ECU (ECU INPUT)

NG

REPLACE STOP LIGHT CONTROL ECU

5.INSPECT SKID CONTROL ECU (ECU INPUT)
a.
C215678E11
2.563,0.969 2.938,1.198 0.375,0.229 2.688,2.365 2.688,1.615 true 0.156,0.104 0.396,0.323 0.24,0.219 10 false *a 2.635,1 2.99,1.208 0.354,0.208 10 false A50 2.385,2.427 3.063,2.646 0.677,0.219 10 false 18 (EXO)

Turn the ignition switch off.


b.

Reconnect the skid control ECU connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A50-18 (EXO) - Body ground Ignition switch ON 11 to 14 V

Text in Illustration
*a Component with harness connected
(Skid Control ECU)



Result:
Proceed to
OK
NG



OK

6.RECONFIRM DTC

NG

REPLACE SKID CONTROL ECU

6.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Drive the vehicle at a speed of 6 km/h (4 mph) or more for 10 seconds or more.



Result:
Result Proceed to
DTC (C1266/66) is not output A
DTC (C1266/66) is output B



A

B

REPLACE SKID CONTROL ECU