Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the skid control ECU to display the DTC by blinking the ABS warning light.

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECU is suspected.


WIRING DIAGRAM

C375216E01
0.927,0.885 1.24,1.083 0.313,0.198 10 false TC 0.885,1.771 1.198,1.969 0.313,0.198 10 false CG 1.271,0.76 1.583,0.958 0.313,0.198 10 false 13 1.302,1.656 1.615,1.854 0.313,0.198 10 false 4 5.76,0.75 6.073,0.948 0.313,0.198 10 false 2 6.042,0.885 6.354,1.083 0.313,0.198 10 false TC 5.927,2.813 6.885,3.021 0.958,0.208 10 false A49*1, B53*2 5.927,3.031 7.083,3.271 1.156,0.24 10 false Skid Control ECU 0.333,2.792 0.646,2.99 0.313,0.198 10 false J45 0.323,2.958 0.948,3.219 0.625,0.26 10 false DLC3 0.781,3.375 1.656,3.625 0.875,0.25 10 false *1: for LHD 2.042,3.365 3.188,3.594 1.146,0.229 10 false *2: for RHD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TC of DLC3)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
B53-2 (TC) - J45-13 (TC) Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
A49-2 (TC) - J45-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-13 (TC) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click HereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU

NG

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU