Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  TS and CG Terminal Circuit  


DESCRIPTION

In the Test Mode (signal check), a malfunction of the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Transition to the sensor check mode can be performed by connecting terminals TS and CG of the DLC3 and turning the ignition switch from off to ON.

WIRING DIAGRAM

C375216E02
0.927,0.885 1.24,1.083 0.313,0.198 10 false TS 0.885,1.771 1.198,1.969 0.313,0.198 10 false CG 1.271,0.76 1.583,0.958 0.313,0.198 10 false 12 1.302,1.656 1.615,1.854 0.313,0.198 10 false 4 5.76,0.75 6.073,0.948 0.313,0.198 10 false 8 6.042,0.896 6.406,1.115 0.365,0.219 10 false TS 5.927,2.813 6.885,3.021 0.958,0.208 10 false A49*1, B53*2 5.927,3.031 7.083,3.271 1.156,0.24 10 false Skid Control ECU 0.333,2.792 0.646,2.99 0.313,0.198 10 false J45 0.323,2.958 0.948,3.219 0.625,0.26 10 false DLC3 0.781,3.375 1.656,3.625 0.875,0.25 10 false *1: for LHD 2.042,3.365 3.188,3.594 1.146,0.229 10 false *2: for RHD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TS of DLC3)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
B53-8 (TS) - J45-12 (TS) Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
A49-8 (TS) - J45-12 (TS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-12 (TS) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click HereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR