Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2017.01–2018.07
RM2850E _56 Audio / Visual / Telematics _073196 AUDIO / VIDEO _0356891 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and microphone amplifier assembly illuminations when the light control switch is in the tail or head position.

WIRING DIAGRAM

E362363E01
0.156,0.146 2.177,0.396 2.021,0.25 12 false w/ Microphone Amplifier: 0.615,0.948 1.75,1.177 1.135,0.229 10 false from TAIL Relay 1.958,1.156 2.594,1.365 0.635,0.208 10 false PANEL 3.115,2.813 3.615,3.021 0.5,0.208 10 false GND 1.865,4.219 2.146,4.396 0.281,0.177 10 false o2 3.115,3.583 3.615,3.792 0.5,0.208 10 false ILL+ 3.531,2.708 3.813,2.885 0.281,0.177 10 false 7 3.521,3.49 3.802,3.667 0.281,0.177 10 false 10 4.625,0.854 4.906,1.031 0.281,0.177 10 false 16 4.625,1.479 4.906,1.656 0.281,0.177 10 false 10 4.677,2.719 4.958,2.896 0.281,0.177 10 false 1 4.635,3.479 4.917,3.656 0.281,0.177 10 false 15 4.896,1.552 5.396,1.76 0.5,0.208 10 false GND 4.885,0.938 5.385,1.146 0.5,0.208 10 false ILL+ 4.885,2.823 5.385,3.031 0.5,0.208 10 false GND 4.896,3.583 5.396,3.792 0.5,0.208 10 false ILL+ 4.875,4.25 5.156,4.427 0.281,0.177 10 false o1 1.854,4.406 3.615,4.635 1.76,0.229 10 false Radio Receiver Assembly 4.854,4.427 6.948,4.656 2.094,0.229 10 false Microphone Amplifier Assembly

E362364E01
0.115,0.125 2.219,0.375 2.104,0.25 12 false w/o Microphone Amplifier: 1,1.146 2.167,1.365 1.167,0.219 10 false from TAIL Relay 2.313,1.333 2.885,1.552 0.573,0.219 10 false PANEL 4,1.156 4.375,1.354 0.375,0.198 10 false ILL+ 5.333,1.146 5.708,1.344 0.375,0.198 10 false GND 3.719,1.031 4.01,1.229 0.292,0.198 10 false 10 5.74,1.042 6.031,1.24 0.292,0.198 10 false 7 3.958,2.01 4.25,2.208 0.292,0.198 10 false J55 3.958,2.208 5.677,2.385 1.719,0.177 10 false Radio Receiver Assembly

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, microphone amplifier assembly or others (hazard switch, combination meter assembly, etc.) comes on when the light control switch is turned to the head or tail position.


Result:
Result Proceed to
Illumination comes on for all components except radio receiver assembly. (w/ microphone amplifier) A
Illumination comes on for all components except radio receiver assembly. (w/o microphone amplifier) B
No illumination comes on (radio receiver assembly, hazard switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (MICROPHONE AMPLIFIER - POWER SOURCE, BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)

C

GO TO LIGHTING SYSTEM

2.CHECK HARNESS AND CONNECTOR (MICROPHONE AMPLIFIER - POWER SOURCE, BODY GROUND)
a.
E362374E01
1.448,0.563 1.927,0.792 0.479,0.229 2.781,1.531 2.896,0.896 true 1.656,2.688 1.823,2.156 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.615,0.594 1.927,0.792 0.313,0.198 10 false o1 2.75,0.719 3.167,0.917 0.417,0.198 10 false GND 1.542,2.729 1.958,2.927 0.417,0.198 10 false ILL+

Disconnect the o1 connector from the microphone amplifier assembly.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o1-10 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
o1-16 (ILL+) - Body ground Light control switch tail or head 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Microphone Amplifier Assembly)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)
a.
E362373E01
1.448,0.708 1.938,0.958 0.49,0.25 2.75,2.833 2.563,2.333 true 1.375,2.833 1.531,2.365 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.583,0.74 1.896,0.938 0.313,0.198 10 false o2 1.229,2.875 1.656,3.063 0.427,0.188 10 false GND 2.646,2.865 3.073,3.052 0.427,0.188 10 false ILL+

Disconnect the o2 connector from the radio receiver assembly.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o2-7 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
o2-10 (ILL+) - Body ground Light control switch tail or head 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - MICROPHONE AMPLIFIER)
4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - MICROPHONE AMPLIFIER)
a.

Disconnect the o2 connector from the radio receiver assembly.


b.

Disconnect the o1 connector from the microphone amplifier assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o2-7 (GND) - o1-1 (GND) Always Below 1 Ω
o2-10 (ILL+) - o1-15 (ILL+) Always Below 1 Ω
o2-7 (GND) - Body ground Always 10 kΩ or higher
o2-10 (ILL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MICROPHONE AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)
a.
E362373E02
1.406,0.719 1.958,0.979 0.552,0.26 1.365,2.813 1.552,2.375 true 2.719,2.802 2.583,2.354 true 0.219,0.229 0.531,0.427 0.313,0.198 10 false *a 1.563,0.771 1.958,0.969 0.396,0.198 10 false J55 1.188,2.844 1.583,3.042 0.396,0.198 10 false GND 2.604,2.865 3,3.063 0.396,0.198 10 false ILL+

Disconnect the J55 connector from the radio receiver assembly.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J55-7 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
J55-10 (ILL+) - Body ground Light control switch tail or head 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR