Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM2850E _56 Audio / Visual / Telematics _073196 AUDIO / VIDEO _0356891 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio receiver assembly.

WIRING DIAGRAM

E362365E01
0.188,0.125 2.208,0.344 2.021,0.219 12 false w/ Microphone Amplifier: 0.729,0.615 1.656,0.844 0.927,0.229 10 false from Battery 0.521,1.198 1.729,1.438 1.208,0.24 10 false from ACC Relay 1.854,0.792 2.427,1 0.573,0.208 10 false RADIO 1.906,1.365 2.313,1.573 0.406,0.208 10 false ACC 2.052,3.313 2.458,3.521 0.406,0.208 10 false ACC 2.219,2.823 2.448,3.01 0.229,0.188 10 false B 2.052,3.823 2.49,4.01 0.438,0.188 10 false GND 5.323,3.833 5.76,4.021 0.438,0.188 10 false GND 5.323,0.656 5.76,0.844 0.438,0.188 10 false +B1 5.344,1.229 5.781,1.417 0.438,0.188 10 false ACCI 5.333,3.344 5.813,3.531 0.479,0.188 10 false ACCO 5.333,2.833 5.771,3.021 0.438,0.188 10 false +BO 5.344,1.823 5.781,2.01 0.438,0.188 10 false GND 2.479,2.719 2.708,2.906 0.229,0.188 10 false 4 2.479,3.229 2.708,3.417 0.229,0.188 10 false 3 2.469,3.698 2.698,3.885 0.229,0.188 10 false 7 5.01,0.51 5.281,0.688 0.271,0.177 10 false 20 5.042,1.104 5.313,1.281 0.271,0.177 10 false 19 5.031,1.688 5.302,1.865 0.271,0.177 10 false 10 5.042,2.74 5.313,2.917 0.271,0.177 10 false 11 5.052,3.24 5.323,3.417 0.271,0.177 10 false 12 5.115,3.708 5.385,3.885 0.271,0.177 10 false 1 1.385,4.219 1.615,4.406 0.229,0.188 10 false o2 1.375,4.406 3.156,4.604 1.781,0.198 10 false Radio Receiver Assembly 5.063,4.208 5.292,4.396 0.229,0.188 10 false o1 5.063,4.417 7.094,4.615 2.031,0.198 10 false Microphone Amplifier Assembly

E362366E01
0.167,0.125 2.302,0.365 2.135,0.24 12 false w/o Microphone Amplifier: 1.146,0.708 2.052,0.927 0.906,0.219 10 false from Battery 0.917,1.177 2.094,1.406 1.177,0.229 10 false from ACC Relay 2.333,0.885 2.896,1.094 0.563,0.208 10 false RADIO 2.396,1.344 2.865,1.552 0.469,0.208 10 false ACC 5.302,1.188 5.771,1.396 0.469,0.208 10 false ACC 5.302,0.74 5.542,0.938 0.24,0.198 10 false B 5.281,1.677 5.75,1.885 0.469,0.208 10 false GND 5.042,0.625 5.281,0.823 0.24,0.198 10 false 4 5.042,1.052 5.281,1.25 0.24,0.198 10 false 3 5.042,1.573 5.281,1.771 0.24,0.198 10 false 7 5.229,2.063 5.594,2.281 0.365,0.219 10 false J55 5.219,2.271 7.031,2.458 1.813,0.188 10 false Radio Receiver Assembly

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Vehicle Condition Proceed to
w/ microphone amplifier A
w/o microphone amplifier B



A

2.CHECK HARNESS AND CONNECTOR (MICROPHONE AMPLIFIER - POWER SOURCE, BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MICROPHONE AMPLIFIER - POWER SOURCE, BODY GROUND)
a.
E362374E02
1.427,0.604 1.906,0.885 0.479,0.281 2.771,1.542 2.958,0.927 true 2.271,2.615 2.49,2.156 true 2.969,2.615 2.75,2.135 true 0.198,0.146 0.51,0.344 0.313,0.198 10 false *a 1.583,0.646 1.896,0.844 0.313,0.198 10 false o1 2.833,0.75 3.229,0.938 0.396,0.188 10 false GND 2.104,2.677 2.542,2.865 0.438,0.188 10 false ACCI 2.854,2.677 3.229,2.865 0.375,0.188 10 false +B1

Disconnect the o1 connector from the microphone amplifier assembly.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o1-10 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
o1-19 (ACCI) - Body ground Ignition switch ACC 11 to 14 V
o1-20 (+B1) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Microphone Amplifier Assembly)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)
a.
E362373E03
1.406,0.594 1.948,0.875 0.542,0.281 2.219,1.656 2.156,1.063 true 2.594,1.677 2.74,1.063 true 1.313,2.865 1.51,2.354 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 1.594,0.646 1.906,0.844 0.313,0.198 10 false o2 2.042,0.875 2.438,1.073 0.396,0.198 10 false ACC 2.74,0.885 3.135,1.083 0.396,0.198 10 false B 1.146,2.885 1.542,3.083 0.396,0.198 10 false GND

Disconnect the o2 connector from the radio receiver assembly.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o2-7 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
o2-4 (B) - Body ground Always 11 to 14 V
o2-3 (ACC) - Body ground Ignition switch ACC 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (MICROPHONE AMPLIFIER - RADIO RECEIVER)
4.CHECK HARNESS AND CONNECTOR (MICROPHONE AMPLIFIER - RADIO RECEIVER)
a.

Disconnect the o2 connector from the radio receiver assembly.


b.

Disconnect the o1 connector from the microphone amplifier assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
o2-4 (B) - o1-11 (+BO) Always Below 1 Ω
o2-3 (ACC) - o1-12 (ACCO) Always Below 1 Ω
o2-7 (GND) - o1-1 (GND) Always Below 1 Ω
o2-4 (B) - Body ground Always 10 kΩ or higher
o2-3 (ACC) - Body ground Always 10 kΩ or higher
o2-7 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MICROPHONE AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - POWER SOURCE, BODY GROUND)
a.
E362373E04
1.385,0.573 1.969,0.885 0.583,0.313 2.229,1.646 2.156,1.073 true 2.594,1.656 2.729,1.094 true 1.333,2.823 1.51,2.365 true 0.198,0.146 0.51,0.344 0.313,0.198 10 false *a 2.01,0.917 2.448,1.115 0.438,0.198 10 false ACC 1.573,0.635 2.01,0.833 0.438,0.198 10 false J55 2.698,0.927 2.969,1.125 0.271,0.198 10 false B 1.177,2.854 1.615,3.052 0.438,0.198 10 false GND

Disconnect the J55 connector from the radio receiver assembly.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J55-7 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
J55-4 (B) - Body ground Always 11 to 14 V
J55-3 (ACC) - Body ground Ignition switch ACC 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR