Home › Engine / Hybrid System › N04C-UH (INTAKE) › TURBOCHARGER › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073299 N04C-UH INTAKE _0356957 TURBOCHARGER A

N04C-UH INTAKE  TURBOCHARGER  REMOVAL  


PROCEDURE

Hide 58521D 1.REMOVE ENGINE SERVICE HOLE COVER MAT (w/ Carpet)

Hide 58410 2.REMOVE ENGINE SERVICE HOLE COVER

Hide 58734B 3.REMOVE ENGINE SERVICE COVER WEATHERSTRIP REAR

Hide 58521D 4.REMOVE ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58420 5.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58534A 6.REMOVE TRANSMISSION COVER MAT (for Manual Transmission)

Hide 33531B 7.REMOVE SHIFT AND SELECT LEVER SHAFT DUST BOOT (for LHD)

a.
A146692

Remove the shift lever knob.


b.

Remove the 4 bolts and shift and select lever support with boots.


Hide 58848A 8.REMOVE SHIFT LEVER HOLE COVER WITH BOOTS (for RHD)

a.

Remove the shift lever knob.


b.
A430966

Remove the 4 bolts and shift lever hole cover with boots.


Hide 33820B 9.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)

a.
A430968E01
2.083,0.042 2.292,0.229 0.208,0.188 10 true (a) 1.063,0.177 1.271,0.365 0.208,0.188 10 true (b) 2.031,1.771 2.24,1.958 0.208,0.188 10 true (a) 0.979,1.823 1.188,2.01 0.208,0.188 10 true (b)

Remove the 2 clips from the shift lever retainer.


b.

Remove the nut and clip, and disconnect the shift cable and select cable.

NOTICE:

Do not sway control cable and over 8° and apply load.



c.
C147947

Remove the nut and separate the shift wire clamp from the engine service cover front panel sub-assembly.


d.
C147948

Remove the bolt and disconnect the transmission control cable clamp.


Hide 33820B 10.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)

a.
A430968E01
2.083,0.042 2.292,0.229 0.208,0.188 10 true (a) 1.063,0.177 1.271,0.365 0.208,0.188 10 true (b) 2.031,1.771 2.24,1.958 0.208,0.188 10 true (a) 0.979,1.823 1.188,2.01 0.208,0.188 10 true (b)

Remove the 2 clips from the shift lever retainer.


b.

Remove the nut and clip, and disconnect the shift cable and select cable.

NOTICE:

Do not sway control cable and over 8° and apply load.



c.
C147948

Remove the bolt and disconnect the transmission control cable clamp.


Hide 33504F 11.REMOVE SHIFT LEVER SUB-ASSEMBLY (for Manual Transmission)

a.
A146695E01
0.072,0.042 0.733,0.209 0.66,0.167 12 for LHD: 0.053,2.491 0.725,2.655 0.672,0.163 12 for RHD:

Remove the 4 bolts and the shift lever assembly.


Hide 58841A 12.REMOVE SHIFTING HOLE COVER (for Automatic Transmission)

Hide 33820B 13.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 33503F 14.REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for Automatic Transmission)

Hide 58701A 15.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for LHD)

a.
A146697

Remove the 3 bolts and the engine service cover front panel sub-assembly.


Hide 58701A 16.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for RHD)

a.
A146698

Remove the 4 bolts and the engine service cover front panel sub-assembly.


Hide 51459 17.REMOVE ENGINE SIDE COVER STAY (for TCAP Made)

a.

Remove the 8 clips and the 2 engine side cover stays.


Hide 51441D 18.REMOVE NO. 1 ENGINE UNDER COVER (for Plastic Type)

a.

Remove the bolts and the No. 1 engine under cover.

Number of Bolts:
Vehicle Maker Bolts
for TCAP Made 8
except TCAP Made 12



Hide 51441D 19.REMOVE NO. 1 ENGINE UNDER COVER (for Metal Type)

a.

Remove the 6 bolts and the No. 1 engine under cover.


Hide 53711C 20.REMOVE FRONT FENDER APRON RH

a.
A146700

Remove the 7 bolts and the front fender apron RH.


Hide 16206C 22.SEPARATE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A218753

Separate the 2 water by-pass hoses


b.
A218754

Remove the 6 bolts and separate the water by-pass pipe sub-assembly.


Hide 17113 23.REMOVE INTAKE PIPE

a.
A218755

Loosen the hose clamp of the inlet hose.


b.

Remove the bolt, the 2 nuts, the inlet pipe and gasket.


Hide 17271 24.REMOVE NO. 1 TURBO INSULATOR

a.
A218756

Remove the 5 bolts and the No. 1 turbo insulator.


Hide 25608 25.REMOVE EGR COOLER SUB-ASSEMBLY

a.
A146460

Disconnect the water by-pass hose.


b.
A218757

Disconnect the 3 water by-pass hoses.


c.
A218758

Disengage the harness clamp.


d.

Remove the 2 bolts and harness bracket.


e.

Remove the 4 bolts, EGR cooler sub-assembly and 2 gaskets.


Hide 17341F 26.SEPARATE NO. 1 AIR HOSE

a.
A180190

Remove the bolt from the No. 1 air hose.


b.

Loosen the hose clamp and separate the No. 1 air hose from the turbocharger.


Hide 44773D 27.DISCONNECT SOLENOIDO TO RETARDER HOSE

a.
A144575

Disconnect the solenoid to retarder hose.


Hide 17410 28.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.
A146709

Remove the 3 nuts.


b.

Remove the bolt and separate the pipe clamp.


c.
A146711

Remove the 4 bolts, the front exhaust pipe assembly and the exhaust retarder.


d.
A144580

Remove the 2 gaskets from the exhaust retarder.


e.
A144578

Remove the gasket from the front exhaust pipe.


Hide 17291 29.REMOVE TURBINE OUTLET ELBOW

a.
A146713

Remove the 2 bolts, 3 nuts, 3 spacers, outlet elbow and gasket.


Hide 16028 30.REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

a.
A159995

Remove the bolt, union bolt, No. 2 turbo water pipe and 2 gaskets.


b.

Remove the O-ring from the No. 2 turbo water pipe.


Hide 15407 31.REMOVE TURBO OIL INLET PIPE

a.
A146714

Remove the bolt, 2 union bolts, turbo oil inlet pipe and 4 gaskets.


Hide 16027 32.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A218783

Remove the nut and the water by-pass pipe support.


b.

Remove the 2 union bolts, No. 1 water by-pass pipe and 4 gaskets.


Hide 15474 33.REMOVE TURBO OIL OUTLET PIPE

a.
A146717

Remove the 4 bolts, turbo oil outlet pipe and 2 gaskets.


Hide 17201 34.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A218759

Disconnect the connector from the turbocharger.


b.
A146719

Remove the 4 nuts, 4 spacers, turbocharger sub-assembly and gasket.


c.
A146722

Remove the 7 stud bolts.