Home › Engine / Hybrid System › 2TR-FE EXHAUST › EXHAUST MANIFOLD
RM2850E _51 Engine / Hybrid System _073296 2TR-FE EXHAUST _0356989 EXHAUST MANIFOLD A

2TR-FE EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17141 1.INSTALL EXHAUST MANIFOLD

a.
A183384

Install a new gasket and the exhaust manifold with the new 6 nuts.

Torque:

36 N*m (367 kgf*cm, 27 ft.*lbf)



Hide 17167 2.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A183383

Install the No. 1 exhaust manifold heat insulator with the 4 bolts.

Torque:

12 N*m (122 kgf*cm, 9 ft.*lbf)



b.
A431296

Install the shift wire clamp with the nut.

Torque:

12 N*m (122 kgf*cm, 9 ft.*lbf)



Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

For rear exhaust type

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.634 in)

If the length is not as specified, replace the compression spring.



ii.
A104635E01
2.518,0.953 2.759,0.953 false 1.509,1.641 2.111,1.452 false 2.765,0.757 3.335,1.141 0.570,0.384 10 Wooden Block 0.884,1.534 1.404,1.748 0.520,0.214 10 Gasket

Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not reuse the exhaust pipe gasket.

·

Do not push in the gasket will the exhaust pipe when connecting it.




iii.
A156777

Install the front exhaust pipe assembly with the 2 compression springs and the 2bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



iv.

Install a new gasket onto the front exhaust pipe assembly.


v.

Install a new gasket onto the catalytic with pipe converter assembly.


vi.
A156778

Install the catalytic with pipe converter assembly with the 2 nuts and the 2 bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)




b.

For side exhaust type

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.634 in)

If the length is not as specified, replace the compression spring.



ii.

Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not reuse the exhaust pipe gasket.

·

Do not push in the gasket will the exhaust pipe when connecting it.




iii.
A156777

Install the front exhaust pipe assembly with the 2 compression springs and the 2 bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



iv.

Install a new gasket onto the front exhaust pipe assembly.


v.

Install a new gasket onto the center exhaust pipe assembly.


vi.
A180098

Install the center exhaust pipe assembly with the 2 nuts and the 2 bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)




Hide 17861 4.INSTALL INTAKE AIR CONNECTOR

Hide 58701A 5.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY

Hide 33506F 6.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

Hide 58123A 7.INSTALL SHIFT AND SELECT LEVER SUPPORT WITH BOOTS

Hide 58420 8.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58521D 9.INSTALL ENGINE SERVICE HOLE COVER MAT

Hide 58734B 10.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

Hide 58410 11.INSTALL ENGINE SERVICE HOLE COVER