Home › Engine / Hybrid System › N04C-UH (INTAKE) › INTAKE SYSTEM
RM2850E _51 Engine / Hybrid System _073299 N04C-UH INTAKE _0357025 INTAKE SYSTEM G

N04C-UH INTAKE  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK TURBOCHARGER PRESSURE

a.
A146685E01
0.163,0.279 0.462,0.424 0.298,0.145 10 SST 0.525,0.366 1.036,0.563 false

Warm up the engine.


b.

Using a 3-way connector, connect SST (turbocharger pressure gauge) to the hose between the turbo pressure sensor and the No. 1 air hose.

SST
09992-00242  


c.

Depress the clutch pedal, and then fully depress the accelerator pedal. Measure the turbocharging pressure at maximum speed (approximately 3600 to 3700 rpm).

Standard pressure:

10 to 20 kPa (0.10 to 0.20 kgf/cm2, 1.5 to 2.9 psi)

If the pressure is less than the minimum, check the intake air and exhaust system for leakage. If there is no leakage, perform the "check motor for turbocharger control operation" procedures below. If the result is not as specified, replace the turbocharger.



Hide 2.INSPECT TURBO PRESSURE SENSOR

a.
A146686E02
1.073,0.156 1.302,0.615 false 1.771,0.167 1.438,0.615 false 0.708,0.063 1.01,0.24 0.302,0.177 10 true E (-) 1.781,0.073 2.219,0.25 0.438,0.177 10 true VC (+)

Inspect the power source voltage.

i.

Disconnect the sensor connector.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage between terminals B18-3 (VC) and B18-1 (E) of the wire harness side connector.

Standard Voltage:

4.5 to 5.5 V


If the result is not as specified, inspect the wire harness or ECM.

Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM


iv.

Turn the ignition switch off.


v.

Connect the sensor connector.



b.
G102567E01
0.792,2.25 1.146,2.438 0.354,0.188 2.104,2.25 2.458,2.438 0.354,0.188 1.427,3.74 1.427,3.406 false 2.833,3.74 2.833,3.406 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *1 0.865,2.271 1.177,2.469 0.313,0.198 10 false B59 2.167,2.26 2.479,2.458 0.313,0.198 10 false B60 1.281,3.76 1.708,4.01 0.427,0.25 10 false E2 (-) 2.604,3.75 3.083,3.969 0.479,0.219 10 true PIM (+)

Check the power supply.

Text in Illustration
*1 ECM

i.

Turn the ignition switch to ON.


ii.

Disconnect the vacuum hose from the sensor.


iii.

Connect a voltmeter to terminals B60-28 (PIM (+)) and B59-28 (E2 (-)) of the ECM.


iv.
A146687E05
1.229,1.208 1.198,1.417 false 1.021,1.448 1.323,1.635 0.302,0.188 10 true SST 2.271,1.042 2.448,1.198 0.177,0.156 10 true *a

Using SST (a turbocharger pressure gauge), apply the following amount of pressure.

Text in Illustration
*a Pressure

SST
09992-00242  

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Applied Pressure kPa (kgf/cm2, psi) Specified condition

If the result is not as specified, replace the turbo pressure sensor.

93.0 (0.95, 13.5) 0.25 to 0.40 V
150 (1.53, 21.8) 1.0 to 1.4 V



v.

Turn the ignition switch to off.


vi.

Connect the vacuum hose.



Hide 3.CHECK MOTOR FOR TURBOCHARGER CONTROL OPERATION

a.

Check the turbocharger control actuator (DC motor) operation.

NOTICE:

Make sure the DC motor connectors are properly installed.


i.
A226917

Turn the ignition switch from ON to off.

Text in Illustration
V100135

VN (Variable Nozzle) open
V100136

VN (Variable Nozzle) close


ii.

Check the turbocharger control actuator (DC motor) operation.

NOTICE:

Never loosen or tighten the fully closed stopper lock nut.


OK:

When the ignition switch is turned from ON to off, the turbocharger control actuator rod moves in the opening direction, then moves back in the closing direction and stops.


If the result is not as specified, check the ECM and turbocharger control actuator.

Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM



Hide 4.INSPECT TURBOCHARGER CONTROL ACTUATOR

a.
A146689E05
0.625,0.552 0.896,0.781 0.271,0.229 2.375,0.177 1.542,0.583 false 2.417,0.063 3.042,0.229 0.625,0.167 10 false +B 0.719,0.573 1.01,0.75 0.292,0.177 10 false j4

Check the voltage of the turbocharger control actuator.

i.

Turn the ignition switch to ON.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
j4-3 (+B) - Body ground Ignition Switch ON 9 to 14 V


If the voltage is not as specified, check the wire harness and connector.



b.
A146690E07
0.438,0.823 0.729,1.042 0.292,0.219 2.031,1.26 2.448,1.26 false 1.417,1.333 1.01,1.74 false 1.417,0.938 1.01,0.531 false 2.479,1.167 2.833,1.323 0.354,0.156 10 false GND 0.104,0.052 0.281,0.229 0.177,0.177 10 false *a 0.531,0.854 0.708,1.031 0.177,0.177 10 false j4 0.625,0.396 1.052,0.552 0.427,0.156 10 false CANH 0.656,1.677 1.063,1.833 0.406,0.156 10 false CANL

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Turbocharger Actuator)

i.

Turn the ignition switch off.


ii.

Disconnect the j4 turbocharger control actuator connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the resistance is not as specified, check the wire harness and connector.

j4-6 (GND) - Body ground Always Below 1 Ω
j4-1 (CANH) - j4-4 (CANL) 105 to 135 Ω




c.

Connect the j4 turbocharger control actuator connector.