Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

These DTCs relate to the throttle position sensor.

The throttle position sensor is mounted on the throttle with motor body assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme conditions.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.

A430114E01
4.167,1.052 4.323,0.615 4.323,0.615 4.427,0.615 false 1.021,2.198 0.729,1.052 true 1.021,2.563 1.823,1.313 true 1,2.958 0.479,3.531 true 1,3.313 1.531,3.688 true 4.74,2.313 4.979,2.479 false 4.677,1.438 4.969,1.646 false 5.063,1.958 5.417,2.26 false 5.583,0.198 5.729,0.198 5.729,0.198 5.917,1.427 true 5.458,2.208 6.01,2.396 0.552,0.188 10 false 1.11 V 4.302,1.313 4.76,1.531 0.458,0.219 10 false VTA2 2.448,0.542 4.156,0.771 1.708,0.229 10 false Sensor Output Voltage (V) 4.469,0.531 5.708,0.76 1.24,0.229 10 false Fail-safe Angle 4.198,3.531 6.604,3.729 2.406,0.198 10 false Throttle Valve Opening Angle (°) 3.625,1.833 4,2.031 0.375,0.198 10 false *2.58 3.615,2.323 4.052,2.521 0.438,0.198 10 false *0.95 3.677,2 3.99,2.198 0.313,0.198 10 false 2.25 3.667,2.479 4.01,2.667 0.344,0.188 10 false 0.69 5.021,2.438 5.479,2.656 0.458,0.219 10 false VTA1 4.771,3.156 5.917,3.354 1.146,0.198 10 false Usable Range 3.958,3.25 4.313,3.448 0.354,0.198 10 false 0 4.104,2.833 4.365,3.031 0.26,0.198 10 false 6.5 6.271,3.26 6.656,3.458 0.385,0.198 10 false 84 0.073,4.375 0.583,4.573 0.51,0.198 10 false Note: 0.073,4.76 3.438,5.115 3.365,0.354 10 false The throttle valve opening angle detected by the sensor terminal VTA1 is expressed as a percentage. 0.073,5.49 3.271,5.719 3.198,0.229 10 false Between 10% and 22%: Throttle valve fully closed 0.073,5.844 3.177,6.073 3.104,0.229 10 false Between 64% and 96%: Throttle valve fully open 0.073,6.219 3.073,6.448 3,0.229 10 false Approximately 19%: Fail safe angle (6.5°) 0.229,0.917 0.865,1.198 0.635,0.281 10 false Magnet 0.083,4.031 1.604,4.396 1.521,0.365 10 false Throttle Position Sensor 1.583,3.625 2.094,3.823 0.51,0.198 10 false Magnet 1.865,1.188 2.5,1.406 0.635,0.219 10 false IC No. 1 0.313,3.563 0.948,3.781 0.635,0.219 10 false IC No. 2 2.406,4.031 2.917,4.229 0.51,0.198 10 false ECM 1.833,2.031 2.115,2.229 0.281,0.198 10 false VC 1.833,3.135 2.125,3.313 0.292,0.177 10 false E2 1.708,2.375 2.115,2.583 0.406,0.208 10 false VTA1 1.708,2.75 2.156,2.958 0.448,0.208 10 false VTA2 4.073,3.938 5.667,4.135 1.594,0.198 10 false *: During fail-safe control 3.854,5.49 7.104,5.667 3.25,0.177 10 false VTA2 x 0.8 is approximately equal to VTA + 1.11 V 3.854,5.146 5.906,5.344 2.052,0.198 10 false Characteristics of sensor output: 3.896,0.125 5.552,0.313 1.656,0.188 10 false Line indicating VTA2 x 0.8 3.75,1.177 4.01,1.375 0.26,0.198 10 false 5.0

DTC No. DTC Detection Condition Trouble Area
P0120 Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body)

·

ECM


P0121 Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds
(1 trip detection logic)
·

Throttle position sensor (built into throttle body)

·

Throttle position sensor circuit

·

ECM


P0122 Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


P0123 Output voltage of VTA1 is 4.8 V or more for 2 seconds or more when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body)

·

Open in VTA1 circuit

·

Open in E2 circuit

·

Short in VC and VTA1 circuits

·

ECM


P0220 Output voltage of VTA2 quickly fluctuates beyond both lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body)

·

ECM


P0222 Output voltage of VTA2 is 0.5 V or less for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


P0223 Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 1.8 V for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body)

·

Open in VTA2 circuit

·

Open in E2 circuit

·

Short in VC and VTA2 circuits

·

ECM


P2135 Either of the following conditions is met (1 trip detection logic):
(a) Difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 0.5 V or less for 0.4 seconds or more
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle body)

·

ECM



HINT:
·

When any of these DTCs are stored, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.

·

Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.



Reference (Normal Condition):
Tester Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No. 1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No. 2 2.1 to 3.1 V 4.6 to 5.0 V


MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm that the throttle position sensor is operating properly.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135
·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor and stores a DTC.



P0121

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm that the throttle position sensor and VTA1 are operating properly.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the throttle position sensor. The ECM illuminates the MIL and stores the DTC.


FAIL-SAFE

When any of these DTCs as well as other DTCs relating to electronic throttle control system malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A401743E01
0.167,2.969 0.51,3.156 0.344,0.188 10 false B65 0.167,3.125 2.771,3.479 2.604,0.354 10 false Throttle Position Sensor (Built into Throttle with Motor Body Assembly) 5.771,3 6.115,3.188 0.344,0.188 10 false B73 5.771,3.156 6.156,3.344 0.385,0.188 10 false ECM 1.719,0.635 2,0.823 0.281,0.188 10 false VC 1.656,1.208 1.99,1.396 0.333,0.188 10 false VTA 1.594,1.75 1.99,1.948 0.396,0.198 10 false VTA2 1.729,2.313 1.979,2.521 0.25,0.208 10 false E2 5.25,0.531 5.531,0.719 0.281,0.188 10 false VC 5.25,1.083 5.688,1.281 0.438,0.198 10 false VTA1 5.26,1.635 5.698,1.833 0.438,0.198 10 false VTA2 5.271,2.292 5.552,2.479 0.281,0.188 10 false E2 6.531,0.396 6.823,0.583 0.292,0.188 10 false 5 V 4.938,0.521 5.167,0.708 0.229,0.188 10 false 18 4.938,1.073 5.167,1.26 0.229,0.188 10 false 20 4.938,1.615 5.167,1.802 0.229,0.188 10 false 19 4.948,2.188 5.177,2.375 0.229,0.188 10 false 28 2.083,0.521 2.24,0.708 0.156,0.188 10 false 5 2.083,1.083 2.24,1.271 0.156,0.188 10 false 6 2.083,1.635 2.24,1.823 0.156,0.188 10 false 4 2.083,2.188 2.24,2.375 0.156,0.188 10 false 3

CAUTION / NOTICE / HINT

HINT:
·

If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION NO. 1, THROTTLE POSITION NO. 2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.


d.

Read the values displayed on the GTS.

Result:
When Accelerator Pedal Released When Accelerator Pedal Depressed Trouble Area Proceed to
Throttle Position No. 1 Throttle Position No. 2 Throttle Position No. 1 Throttle Position No. 2
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VC circuit open A
4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V E2 circuit open A
0 to 0.2 V or 4.5 to 5.0 V 2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V or 4.5 to 5.0 V 2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or ground short A
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V or 4.5 to 5.0 V 0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V or 4.5 to 5.0 V VTA2 circuit open or ground short A
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 5.0 V
(Not fail-safe)
Throttle position sensor circuit is normal B


HINT:
·

DTC P0121 is stored when the VTA and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored.

Calculate the voltage of VTA and VTA2 according to Throttle Sensor Volt % and Throttl Sensor #2 Volt % respectively and confirm their consistency.

Example:

Throttle Sensor Volt % / 100 (%) x 5 (V) = Throttle Position No. 1


Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle position No. 1

VTA2: Throttle position No. 2


·

If DTC P0121 is output, proceed to "Check Harness And Connector (Throttle Position Sensor - ECM)".





A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B65-5 (VC) - B73-18 (VC) Always Below 1 Ω
B65-6 (VTA) - B73-20 (VTA1) Always Below 1 Ω
B65-4 (VTA2) - B73-19 (VTA2) Always Below 1 Ω
B65-3 (E2) - B73-28 (E2) Always Below 1 Ω
B65-5 (VC) or B73-18 (VC) - Body ground Always 10 kΩ or higher
B65-6 (VTA) or B73-20 (VTA1) - Body ground Always 10 kΩ or higher
B65-4 (VTA2) or B73-19 (VTA2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
A200902E78
0.552,0.885 0.979,1.146 0.427,0.26 1.646,1.115 1.448,1.625 true 1.948,1.104 2.135,1.583 true 0.635,0.938 0.969,1.115 0.333,0.177 10 false B65 0.125,0.125 0.396,0.333 0.271,0.208 10 false *a 1.344,1.635 1.594,1.823 0.25,0.188 10 false E2 2.104,1.604 2.375,1.76 0.271,0.156 10 false VC

Disconnect the Throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B65-5 (VC) - B65-3 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)


Result:
Proceed to
OK
NG



OK

4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

NG

4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Replace the throttle with motor body assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine.


f.

Allow the engine to idle for 15 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read DTCs.


Result:
Result Proceed to
DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 A
No DTC output B



A

B

END