Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions related to the primary circuit.

·

If DTC P0351 is displayed, check No. 1 ignition coil assembly circuit.

·

If DTC P0352 is displayed, check No. 2 ignition coil assembly circuit.

·

If DTC P0353 is displayed, check No. 3 ignition coil assembly circuit.

·

If DTC P0354 is displayed, check No. 4 ignition coil assembly circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1 cylinder ignition system which ignites one cylinder with one ignition coil assembly. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High-voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition (IGT) signals for each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter ON and OFF, which turns a current to the primary coil ON and OFF. When the current to the primary coil is cut off, high-voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back the ignition confirmation (IGF) signal to the ECM.

A158510E04
5.375,1.135 5.813,0.854 false 0.292,1.427 1.99,1.604 1.698,0.177 10 false Crankshaft Position Sensor 0.313,3.188 1.938,3.365 1.625,0.177 10 false Camshaft Position Sensor 0.25,4.542 2.042,5.302 1.792,0.76 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, etc.) 1.833,6.094 2.427,6.271 0.594,0.177 10 false To DLC3 2.688,5.667 3.083,5.844 0.396,0.177 10 false TACH 2.719,0.625 3.042,0.802 0.323,0.177 10 false ECM 2.844,1.417 3.208,1.594 0.365,0.177 10 false IGT1 2.844,1.74 3.198,1.917 0.354,0.177 10 false IGF1 2.865,2.719 3.208,2.906 0.344,0.188 10 false IGT2 2.865,4.083 3.219,4.26 0.354,0.177 10 false IGT3 2.865,5.385 3.219,5.563 0.354,0.177 10 false IGT4 4.375,0.635 5.292,0.844 0.917,0.208 10 false From Battery 4.031,0.875 4.5,1.063 0.469,0.188 10 false Igniter 4.604,2.031 5.396,2.208 0.792,0.177 10 false Ignition Coil 5.854,0.74 6.99,1.125 1.135,0.385 10 false No. 1 Ignition Coil Assembly 5.635,1.833 6.698,2.01 1.063,0.177 10 false No. 1 Spark Plug 4.198,2.74 5.333,3.125 1.135,0.385 10 false No. 2 Ignition Coil Assembly 4.188,4.042 5.323,4.427 1.135,0.385 10 false No. 3 Ignition Coil Assembly 4.167,5.344 5.302,5.729 1.135,0.385 10 false No. 4 Ignition Coil Assembly 5.635,3.063 6.74,3.271 1.104,0.208 10 false No. 2 Spark Plug 5.625,4.365 6.74,4.563 1.115,0.198 10 false No. 3 Spark Plug 5.594,5.708 6.719,5.917 1.125,0.208 10 false No. 4 Spark Plug

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine is running
(1 trip detection logic)
·

Ignition system

·

Open or short in IGF or IGT1 to 4 circuit from ignition coil assembly to ECM

·

No. 1 to No. 4 ignition coil assembly

·

ECM



Reference: Inspection using an oscilloscope.

A289263E07
2.854,0.906 3.219,1.104 0.365,0.198 10 false GND 2.854,1.531 3.188,1.729 0.333,0.198 10 false GND 0.063,0.438 0.438,0.938 0.375,0.5 10 false CH1 (IGT) 0.042,1.281 0.458,1.635 0.417,0.354 10 false CH2 (IGF1) 0.052,0.042 0.802,0.438 0.75,0.396 10 false 2 V/DIV. 1.208,1.865 2.073,2.094 0.865,0.229 10 false 20 ms./DIV.

Items Contents
Terminals
1.

IGT1, IGT2, IGT3, IGT4 - E1

2.

IGF1 - E1


Equipment Settings 2 V/DIV, 20 ms./DIV
Conditions Idling

MONITOR DESCRIPTION

A212405E18
1.782,1.645 2.181,1.818 0.4,0.173 10 ECM 2.956,1.3 3.226,1.486 0.27,0.185 10 IGT 2.949,1.726 3.227,1.886 0.278,0.16 10 IGF 4.153,1.509 4.594,1.655 0.441,0.146 10 Igniter 5.4,1.348 6.167,1.522 0.767,0.174 10 Ignition Coil 4.413,2.35 5.843,2.541 1.43,0.191 10 Ignition Coil Assembly 0.213,3.113 1.147,3.443 0.934,0.33 10 Ignition Signal (IGT) 1.642,3.541 2.131,3.732 0.49,0.191 10 Normal 1.383,3.947 2.15,4.138 0.767,0.191 10 Malfunction 0.185,3.891 1.153,4.408 0.969,0.517 10 Ignition Confirmation Signal (IGF) 3.631,4.507 4.482,4.684 0.851,0.177 10 Circuit Open 5.95,4.97 6.315,5.168 0.365,0.198 10 Time

If the ECM does not receive any IGF signal despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC. The monitor runs for 1 second (the first second of engine idle) after the engine is started.

WIRING DIAGRAM

A395987E01
0.625,1.073 1.01,1.24 0.385,0.167 10 false AM1 1.406,1.073 1.688,1.26 0.281,0.188 10 false IG1 0.531,1.583 0.917,1.75 0.385,0.167 10 false J63 0.531,1.75 1.51,1.938 0.979,0.188 10 false Ignition Switch 0.333,2.271 0.719,2.438 0.385,0.167 10 false AM1 0.313,3.26 0.917,3.469 0.604,0.208 10 false J/B ALT 0.323,4.219 0.677,4.396 0.354,0.177 10 false ALT 0.323,6.302 0.927,6.51 0.604,0.208 10 false FL MAIN 0.458,7.521 1.063,7.729 0.604,0.208 10 false Battery 2.552,1.198 2.833,1.385 0.281,0.188 10 false 2C 2.552,1.615 2.833,1.802 0.281,0.188 10 false 2E 4.938,1.188 5.219,1.375 0.281,0.188 10 false 2C 4.948,1.615 5.229,1.802 0.281,0.188 10 false 2C 2.969,1.76 3.635,1.948 0.667,0.188 10 false IG2-NO. 1 3.927,1.938 4.229,2.104 0.302,0.167 10 false IG2 3.26,2.25 4.823,2.438 1.563,0.188 10 false NO. 2 Integration Relay 3.833,2.948 4.094,3.146 0.26,0.198 10 false INJ 1.896,2.479 2.156,2.677 0.26,0.198 10 false P/I 1.875,4.073 2.417,4.427 0.542,0.354 10 false R/B NO. 2-B 3.427,3.688 3.688,3.885 0.26,0.198 10 false +B 3.427,4.063 3.792,4.25 0.365,0.188 10 false GND 4.021,3.688 4.385,3.875 0.365,0.188 10 false IGT1 4.104,4.052 4.375,4.24 0.271,0.188 10 false IGF 5.656,3.51 6.021,3.698 0.365,0.188 10 false IGT1 5.656,4.76 6.021,4.948 0.365,0.188 10 false IGT2 3.417,4.958 3.677,5.156 0.26,0.198 10 false +B 3.417,4.958 3.677,5.156 0.26,0.198 10 false +B 3.427,5.333 3.792,5.521 0.365,0.188 10 false GND 4.031,4.948 4.396,5.135 0.365,0.188 10 false IGT2 4.104,5.344 4.375,5.531 0.271,0.188 10 false IGF 3.438,6.229 3.698,6.427 0.26,0.198 10 false +B 3.417,6.635 3.781,6.823 0.365,0.188 10 false GND 4.021,6.25 4.385,6.438 0.365,0.188 10 false IGT3 4.115,6.625 4.385,6.813 0.271,0.188 10 false IGF 3.427,7.5 3.688,7.698 0.26,0.198 10 false +B 3.417,7.896 3.781,8.083 0.365,0.188 10 false GND 4.01,7.521 4.375,7.708 0.365,0.188 10 false IGT4 4.104,7.906 4.375,8.094 0.271,0.188 10 false IGF 3.052,4.24 3.396,4.427 0.344,0.188 10 false B66 3.052,4.396 4.917,4.604 1.865,0.208 10 false No. 1 Ignition Coil Assembly 3.031,5.531 3.375,5.719 0.344,0.188 10 false B67 3.031,5.677 4.896,5.885 1.865,0.208 10 false No. 2 Ignition Coil Assembly 3.021,6.792 3.365,6.979 0.344,0.188 10 false B68 3.031,6.948 4.896,7.156 1.865,0.208 10 false No. 3 Ignition Coil Assembly 3.052,8.115 3.396,8.302 0.344,0.188 10 false B69 3.052,8.26 4.917,8.469 1.865,0.208 10 false No. 4 Ignition Coil Assembly 6.021,8.281 6.365,8.469 0.344,0.188 10 false B73 6.021,8.438 6.448,8.635 0.427,0.198 10 false ECM 5.656,6.052 6.021,6.24 0.365,0.188 10 false IGT3 5.656,7.354 6.021,7.542 0.365,0.188 10 false IGT4 5.667,7.802 6.031,7.99 0.365,0.188 10 false IGF1 2.583,1 2.74,1.198 0.156,0.198 10 false 6 2.594,1.427 2.75,1.625 0.156,0.198 10 false 1 4.979,0.979 5.135,1.177 0.156,0.198 10 false 7 4.99,1.427 5.146,1.625 0.156,0.198 10 false 8 5.365,3.542 5.583,3.74 0.219,0.198 10 false 17 5.354,4.813 5.573,5.01 0.219,0.198 10 false 16 5.375,6.083 5.594,6.281 0.219,0.198 10 false 15 5.365,7.375 5.583,7.573 0.219,0.198 10 false 14 5.375,7.802 5.594,8 0.219,0.198 10 false 23 4.448,3.521 4.604,3.719 0.156,0.198 10 false 3 3.219,3.958 3.375,4.156 0.156,0.198 10 false 4 3.208,3.552 3.365,3.75 0.156,0.198 10 false 1 4.458,3.958 4.615,4.156 0.156,0.198 10 false 2 3.188,4.802 3.344,5 0.156,0.198 10 false 1 3.188,5.24 3.344,5.438 0.156,0.198 10 false 4 4.458,4.823 4.615,5.021 0.156,0.198 10 false 3 4.458,5.24 4.615,5.438 0.156,0.198 10 false 2 4.448,6.104 4.604,6.302 0.156,0.198 10 false 3 4.448,6.521 4.604,6.719 0.156,0.198 10 false 2 3.198,6.083 3.354,6.281 0.156,0.198 10 false 1 3.198,6.531 3.354,6.729 0.156,0.198 10 false 4 3.208,7.385 3.365,7.583 0.156,0.198 10 false 1 3.219,7.802 3.375,8 0.156,0.198 10 false 4 4.448,7.385 4.604,7.583 0.156,0.198 10 false 3 4.438,7.802 4.594,8 0.156,0.198 10 false 2 0.417,1.063 0.573,1.26 0.156,0.198 10 false 6 1.75,1.052 1.906,1.25 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM SIMULATION TEST

b.

Change the arrangement of the ignition coil assemblies.

NOTICE:

Do not change the location of the connectors.



c.

Perform the simulation test.


Result:
Result Proceed to
Cleared DTCs are output again A
Other DTCs B



A

2.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)

B

REPLACE IGNITION COIL ASSEMBLY

2.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B66-4 (GND) - Body ground Always Below 1 Ω
B67-4 (GND) - Body ground Always Below 1 Ω
B68-4 (GND) - Body ground Always Below 1 Ω
B69-4 (GND) - Body ground Always Below 1 Ω



c.
A179541E03
0.333,0.635 0.729,0.885 0.396,0.25 0.333,0.917 0.729,1.167 0.396,0.25 0.333,1.198 0.729,1.448 0.396,0.25 0.333,1.479 0.729,1.729 0.396,0.25 1.396,1.198 1.396,1.531 true 2.073,1.188 2.073,1.542 true 0.094,0.063 0.323,0.24 0.229,0.177 10 false *a 1.271,1.552 1.563,1.75 0.292,0.198 10 false +B 1.896,1.552 2.281,1.771 0.385,0.219 10 false GND 0.417,0.688 0.708,0.854 0.292,0.167 10 false B66 0.417,0.958 0.708,1.125 0.292,0.167 10 false B67 0.417,1.24 0.729,1.406 0.313,0.167 10 false B68 0.417,1.51 0.708,1.698 0.292,0.188 10 false B69

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B66-1 (+B) - B66-4 (GND) Ignition switch ON 11 to 14 V
B67-1 (+B) - B67-4 (GND) Ignition switch ON 11 to 14 V
B68-1 (+B) - B68-4 (GND) Ignition switch ON 11 to 14 V
B69-1 (+B) - B69-4 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Component without harness connected
(Ignition Coil Assembly)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 2 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B66-2 (IGF) - B73-23 (IGF1) Always Below 1 Ω
B67-2 (IGF) - B73-23 (IGF1) Always Below 1 Ω
B68-2 (IGF) - B73-23 (IGF1) Always Below 1 Ω
B69-2 (IGF) - B73-23 (IGF1) Always Below 1 Ω
B66-3 (IGT1) - B73-17 (IGT1) Always Below 1 Ω
B67-3 (IGT2) - B73-16 (IGT2) Always Below 1 Ω
B68-3 (IGT3) - B73-15 (IGT3) Always Below 1 Ω
B69-3 (IGT4) - B73-14 (IGT4) Always Below 1 Ω
B66-2 (IGF) or B73-23 (IGF1) - Body ground Always 10 kΩ or higher
B67-2 (IGF) or B73-23 (IGF1) - Body ground Always 10 kΩ or higher
B68-2 (IGF) or B73-23 (IGF1) - Body ground Always 10 kΩ or higher
B69-2 (IGF) or B73-23 (IGF1) - Body ground Always 10 kΩ or higher
B66-3 (IGT1) or B73-17 (IGT1) - Body ground Always 10 kΩ or higher
B67-3 (IGT2) or B73-16 (IGT2) - Body ground Always 10 kΩ or higher
B68-3 (IGT3) or B73-15 (IGT3) - Body ground Always 10 kΩ or higher
B69-3 (IGT4) or B73-14 (IGT4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Disconnect the ignition coil assembly connectors.


b.

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B66-1 (+B) - 2C-8 Always Below 1 Ω
B67-1 (+B) - 2C-8 Always Below 1 Ω
B68-1 (+B) - 2C-8 Always Below 1 Ω
B69-1 (+B) - 2C-8 Always Below 1 Ω
B66-1 (+B) or 2C-8 - Body ground Always 10 kΩ or higher
B67-1 (+B) or 2C-8 - Body ground Always 10 kΩ or higher
B68-1 (+B) or 2C-8 - Body ground Always 10 kΩ or higher
B69-1 (+B) or 2C-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR