Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using an electric motor and gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle with motor body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

The Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No. DTC Detection Condition Suspected Area
P2102 Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator output duty ratio is 80% or more
(b) Throttle actuator current is 0.5 A or less
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


P2103 Either of following conditions is met (1 trip detection logic):
·

Throttle actuator current is 10 A or more for 0.1 seconds

·

Throttle actuator current is 7 A or more for 0.6 seconds


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle with motor body assembly

·

ECM



MONITOR DESCRIPTION

The ECM monitors the flow of electrical current through the electronic throttle actuator, and detects malfunctions or open circuits in the throttle actuator based on the value of the electrical current. When the current deviates from the standard values, the ECM concludes that there is a fault in the throttle actuator. Or, if the throttle valve is not functioning properly (for example, stuck ON) the ECM concludes that there is a fault and illuminates the MIL and stores a DTC.

Example:

The current is more than 7 A, or the current is less than 0.5 A when the actuator driving duty ratio exceeds 80%. The ECM concludes that the current deviates from the standard values, turns on the MIL and a DTC is set.

This monitor runs after the engine is started, idled for 5 seconds and then quickly revved at a high rpm several times.

FAIL-SAFE

When any of these DTCs as well as other DTCs relating to electronic throttle control system malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A401735E01
1.313,1.156 2.198,1.344 0.885,0.188 10 false R/B NO. 2-B 2.917,1.156 3.385,1.333 0.469,0.177 10 false ETCS 0.76,2.542 1.406,2.729 0.646,0.188 10 false FL MAIN 0.938,4.073 1.583,4.26 0.646,0.188 10 false Battery 1.615,3.177 1.958,3.365 0.344,0.188 10 false B65 1.625,3.333 3.76,3.698 2.135,0.365 10 false Throttle Actuator (built into Throttle with Motor Body Assembly) 3.823,3.104 4.51,3.313 0.688,0.208 10 false (Shielded) 5.469,0.99 5.792,1.188 0.323,0.198 10 false A55 5.49,2.167 5.813,2.365 0.323,0.198 10 false B73 5.49,2.781 5.813,2.979 0.323,0.198 10 false B73 5.479,3.365 5.802,3.563 0.323,0.198 10 false B73 5.469,4.542 5.792,4.74 0.323,0.198 10 false B73 5.479,3.958 5.802,4.156 0.323,0.198 10 false B75 5.833,0.885 6.208,1.083 0.375,0.198 10 false +BM 5.833,2.031 6.115,2.229 0.281,0.198 10 false M+ 5.833,2.656 6.115,2.854 0.281,0.198 10 false M- 5.833,3.344 6.25,3.531 0.417,0.188 10 false GE01 5.823,3.844 6.24,4.031 0.417,0.188 10 false ME01 5.833,4.531 6.073,4.719 0.24,0.188 10 false E1 6.083,5.115 6.5,5.302 0.417,0.188 10 false ECM 2.719,2.052 3,2.25 0.281,0.198 10 false M+ 2.729,2.646 3.01,2.844 0.281,0.198 10 false M- 3.063,2.031 3.219,2.208 0.156,0.177 10 false 2 3.063,2.656 3.219,2.833 0.156,0.177 10 false 1 5.552,0.802 5.708,0.979 0.156,0.177 10 false 7 5.563,1.958 5.719,2.135 0.156,0.177 10 false 5 5.563,2.594 5.719,2.771 0.156,0.177 10 false 4 5.573,3.177 5.729,3.354 0.156,0.177 10 false 8 5.563,3.781 5.719,3.958 0.156,0.177 10 false 3 5.563,4.365 5.719,4.542 0.156,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.
A059778E89
2.5,1.323 2.667,1.625 true 2.188,1.333 2.094,1.656 true 1.979,1.708 2.313,1.917 0.333,0.208 10 false M+ 2.667,1.656 2.948,1.927 0.281,0.271 10 false M- 0.167,0.115 0.417,0.323 0.25,0.208 10 false *a

Disconnect the throttle with motor body assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (M+) - 1 (M-) 20°C (68°F) 0.3 to 100 Ω


Text in Illustration
*a Component without harness connected
(Throttle With Motor Body Assembly)


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM)

NG

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B65-2 (M+) - B73-5 (M+) Always Below 1 Ω
B65-1 (M-) - B73-4 (M-) Always Below 1 Ω
B65-2 (M+) or B73-5 (M+) - Body ground Always 10 kΩ or higher
B65-1 (M-) or B73-4 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and the housing.

OK:

No foreign objects between throttle valve and housing.



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.



Result:
Proceed to
OK
NG



OK

NG

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY