Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Variable Resistor Circuit  


DESCRIPTION

This resistor is used to change the air-fuel ratio of the air-fuel mixture.

The idle mixture is adjusted using this resistor.

Turning the idle mixture adjusting screw clockwise moves the contacts inside the resistor, raising the terminal VAF voltage. Conversely, turning the screw counterclockwise lowers the terminal VAF voltage.

When the terminal VAF voltage rises, the ECM increases the injection volume slightly, marking the air-fuel mixture a little richer.

WIRING DIAGRAM

A111678E05
0.542,0.531 1.76,0.781 1.219,0.25 10 false Variable Resistor 1.479,1.135 1.792,1.333 0.313,0.198 10 false VC 1.406,1.875 1.802,2.073 0.396,0.198 10 false VAF 1.5,2.625 1.802,2.823 0.302,0.198 10 false E2 5.865,1.25 6.104,1.406 0.24,0.156 10 false VC 5.865,2.01 6.167,2.167 0.302,0.156 10 false VAF 5.865,2.74 6.094,2.896 0.229,0.156 10 false E2 1.802,1.135 2.094,1.344 0.292,0.208 10 false 2 1.792,1.875 2.042,2.094 0.25,0.219 10 false 3 1.792,2.625 2.01,2.844 0.219,0.219 10 false 1 6.083,0.573 6.427,0.729 0.344,0.156 10 false ECM 5.479,1.26 5.844,1.458 0.365,0.198 10 false B73 5.479,2.01 5.823,2.24 0.344,0.229 10 false B73 5.469,2.75 5.823,2.99 0.354,0.24 10 false B73 5.5,1.031 5.688,1.188 0.188,0.156 10 false 18 5.531,1.76 5.844,1.979 0.313,0.219 10 false 25 5.51,2.51 5.76,2.688 0.25,0.177 10 false 28 0.552,0.354 0.938,0.521 0.385,0.167 10 false B90

CAUTION / NOTICE / HINT

NOTICE:

Always use a CO meter when adjusting the idle mixture. If a CO meter is not available, DO NOT ATTEMPT TO ADJUST IDLE MIXTURE.


PROCEDURE

1.CHECK CO/HC
a.

Warm up the engine to normal operating temperature.


b.

Switch all accessories OFF.


c.

Connect all vacuum lines properly.


d.

Connect the tachometer.


e.

Check ignition timing correctly.


f.

Check idle speed correctly.


g.

Check that the CO meter is properly calibrated.


h.

Race the engine at 2,500 rpm about 2 minutes.


i.

Insert a tester probe at least 40 cm (1.3 ft.) into the tailpipe.


j.

Measure the concentration for 1 to 3 minutes after racing the engine to allow the concentration to stabilize.

Idle CO concentration:

1.0 to 2.0 %



Result:
Proceed to
OK
NG



OK

2.ADJUST CO CONCENTRATION

NG

2.ADJUST CO CONCENTRATION
a.
A430119E01
1.49,1.208 0.688,0.417 true 1.51,1.667 0.833,2.177 true 0.354,0.313 0.813,0.51 0.458,0.198 10 false SST 0.177,2.198 1.531,2.542 1.354,0.344 10 false Idle Mixture Adjusting Screw 1.667,4.292 2.021,4.469 0.354,0.177 10 false 180°

Put the vehicle in the same condition as step 1 of this chart.


b.

Using SST, adjust the idle mixture by turning the idle mixture adjusting screw in the variable resistor.

Result:
Result Proceed to
Concentration: 1.0 to 2.0 % B
Change in CO concentration C
No change in CO concentration A


HINT:
·

Always check idle speed after turning the idle mixture adjusting screw. If it is incorrect, readjust idle speed.

·

The idle mixture adjusting screw can be turned within 180 degrees. Do not turn this screw more than the specified.




SST
09243-00020  


A

3.INSPECT VARIABLE RESISTOR

B

ADJUST COMPLETED

C

CHECK CO/HC

3.INSPECT VARIABLE RESISTOR
a.
A074545E05
1.75,2.604 2.333,2.781 true 2.385,2.74 2.76,2.927 0.375,0.188 10 false SST

Measure the resistance according to the value(s) in the table below.

Resistance:
Tester Connection Specified Condition
1 - 2 3.5 to 6.5 Ω



b.

Measure the resistance according to the value(s) in the table below, when turning the idle mixture adjusting screw fully clockwise and counterclockwise using SST.

Resistance:
Tester Connection Specified Condition
2 - 3 Change from about 5 kΩ to 0 kΩ accordingly



SST
09243-00020  

Result:
Proceed to
OK
NG



OK

4.CHECK ECM (VAF VOLTAGE)

NG

4.CHECK ECM (VAF VOLTAGE)
a.
A430121E01
0.448,2.698 0.823,2.917 0.375,0.219 0.229,3.938 0.49,3.396 true 1.021,3.938 0.906,3.469 true 0.823,1.635 1.104,1.323 true 0.688,1.656 1.146,1.854 0.458,0.198 10 false SST 0.521,2.719 0.875,2.927 0.354,0.208 10 false B73 0.104,3.99 0.448,4.177 0.344,0.188 10 false VAF 0.958,3.99 1.26,4.188 0.302,0.198 10 false E2

Turn the ignition switch to the ON position.


b.

Measure the voltage according to the value(s) in the table below while slowly turning the idle mixture adjusting screw first fully counterclockwise and then fully clockwise, using SST.

Voltage:
Tester Connection Specified Condition
B73-25(VAF) - B73-28(E2) Voltage changes smoothly from 0 V to about 5 V, i.e. does not suddenly jump up to 5 V down to 0 V



SST
09243-00020  

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (VARIABLE RESISTOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (VARIABLE RESISTOR - ECM)
a.

Disconnect the variable resistor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Resistance:
Tester Connection Condition Specified Condition
B90-2(VC) - B73-18(VC) Always Below 1 Ω
B90-3(VAF) - B73-25(VAF) Always Below 1 Ω
B90-1(E2) - B73-28(E2) Always Below 1 Ω
B90-2(VC) or B73-18(VC) - Body ground Always 10 kΩ or higher
B90-3(VAF) or B73-25(VAF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR