Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM U

N04C-VL ENGINE CONTROL  ECD SYSTEM  TERMINALS OF ECM  


E191646E27
0.667,0.74 1.021,0.979 0.354,0.24 1.646,0.74 2.01,0.979 0.365,0.24 3.167,0.729 3.573,0.979 0.406,0.25 4.021,0.729 4.438,0.979 0.417,0.25 4.927,0.729 5.344,0.979 0.417,0.25 5.969,0.729 6.406,0.99 0.438,0.26 0.719,0.781 1.01,0.958 0.292,0.177 10 false A57 1.698,0.781 1.99,0.958 0.292,0.177 10 false A56 3.208,0.771 3.552,0.938 0.344,0.167 10 false B105 4.073,0.771 4.448,0.948 0.375,0.177 10 false B104 4.969,0.771 5.344,0.969 0.375,0.198 10 false B103 6.031,0.781 6.427,0.958 0.396,0.177 10 false B102

HINT:

Each ECM terminal's standard voltage is shown in the table below. In the table, first follow the information under "Condition". Look under "Terminal No. (Symbols)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition". Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A56-1 (CANL) - B102-1 (E1) W - BR CAN communication line Engine stop and ignition switch ON Pulse generation(See waveform 1)
A56-6 (VCPA) - A56-5 (EPA) B*1 - LG
L*2 - LG
Power source of accelerator pedal position sensor (accelerator link assembly) Ignition switch ON 4.75 to 5.25 V
A56-7 (CANH) - B102-1 (E1) B - BR CAN communication line Engine stop and ignition switch ON Pulse generation(See waveform 2)
A56-23 (TC) - B102-1 (E1) P - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A56-24 (IGSW) - B102-1 (E1) B - BR Ignition switch Ignition switch ON 11 to 14 V
A56-25 (MREL) - B102-1 (E1) W - BR EFI relay Ignition switch ON 11 to 14 V
5 seconds pass after ignition switch off 0 to 2 V
A57-1 (VPA2) - A56-3 (EPA2) GR - G Accelerator pedal position sensor (accelerator link assembly) (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 1.4 to 1.8 V
A57-2 (VPA) - A56-5 (EPA) G - LG Accelerator pedal position sensor (accelerator link assembly) (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.0 V
Ignition switch ON, accelerator pedal fully depressed 2.8 to 3.6 V
A57-6 (STA) - B102-1 (E1) B - BR Starter signal Cranking 6 V or higher
A57-7 (SPD) - B102-1 (E1) V*1 - BR
Y*2 - BR
Speed signal from combination meter assembly Ignition switch ON, driving wheel slowly rotated Pulse generation(See waveform 3)
A57-8 (STP) - B102-1 (E1) P - BR Stop light switch assembly Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 2 V
A57-9 (ST1-) - B102-1 (E1) V - BR Stop light switch assembly (opposite to STP) Ignition switch ON, brake pedal depressed 0 to 2 V
Ignition switch ON, brake pedal released 11 to 14 V
A57-11 (EC) - Body ground W-B - Body ground Ground Always Below 1 Ω
A57-18 (TAC) - B102-1 (E1) B - BR Engine speed Idling Pulse generation(See waveform 4)
A57-19 (W) - B102-1 (E1) L - BR MIL MIL illuminated 0 to 2 V
MIL not illuminated 11 to 14 V
A57-20 (EXSW) - B102-1 (E1) GR*1 - BR
P*2 - BR
Exhaust brake main switch (windshield wiper switch assembly) Exhaust brake main switch on 11 to 14 V
Exhaust brake main switch off 0 to 2 V
A57-21 (CLSW) - B102-1 (E1) G - BR Exhaust brake clutch switch (exhaust retarder switch assembly) Clutch pedal depressed 0 to 2 V
Clutch pedal released 11 to 14 V
A57-23 (BATT) - B102-1 (E1) GR - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A57-24 (+B) - B102-1 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
B102-1 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
B102-3 (EXB) - B102-1 (E1) GR - BR Exhaust brake solenoid with bracket assembly Exhaust brake operating 11 to 14 V
B102-11 (E01) - Body ground BR - Body ground Ground Always Below 1 Ω
B102-12 (E02) - Body ground BR - Body ground Ground Always Below 1 Ω
B103-7 (NE+) - B103-8 (NE-) B - W Crankshaft position sensor Idling with warm engine Pulse generation(See waveform 5)
B103-13 (G+) - B103-14 (G-) R - G Camshaft position sensor Idling with warm engine Pulse generation(See waveform 5)
B103-15 (VCG) - B103-14 (G-) L - G Power source of camshaft position sensor Ignition switch ON 4.75 to 5.25 V
B103-16 (LUSL) - B102-1 (E1) W - BR Throttle control motor (venturi assembly) duty signal Accelerator pedal released → Accelerator pedal depressed (when throttle control motor is operating) Pulse generation(See waveform 6)
B103-23 (PCV+) - B103-12 (PCV-) L - L Suction control valve Idling Pulse generation(See waveform 7)
B103-21 (NUSW) - B102-1 (E1) GR - BR Exhaust brake neutral switch assembly Ignition switch ON, shift position is neutral 11 to 14 V
Ignition switch ON, shift position is not neutral 0 to 2 V
B103-26 (RSW) - B102-1 (E1) R - BR Back-up light switch assembly Back-up light switch off 0 to 2 V
Back-up light switch on 11 to 14 V
B104-3 (VLU) - B104-14 (E2) W - R Throttle position sensor (venturi assembly) Ignition switch ON, throttle valve fully closed 0.5 to 1.5 V
Ignition switch ON, throttle valve fully opened 3.2 to 4.2 V
B104-5 (PIM) - B104-14 (E2) P - R Vacuum sensor Applied negative pressure of 93 kPa (698 mmHg) 0.25 to 0.4 V
Applied positive pressure of 150 kPa (1125 mmHg) 1.0 to 1.4 V
B104-13 (VC) - B104-14 (E2) L - R Power source of sensor (a specific voltage) Ignition switch ON 4.75 to 5.25 V
B104-14 (E2) - Body ground R - Body ground Ground Always Below 1 Ω
B104-20 (IREL) - B102-1 (E1) R - BR EDU relay Ignition switch ON or Idling 0 to 2 V
B105-2 (PCR2) - B105-14 (E21) LG - R Fuel pressure sensor (common rail assembly) (sub) Idling (Approximately 30 MPa (306 kgf/cm2, 4351 psi)) 1.2 to 1.6 V
B105-4 (THF) - B104-14 (E2) Y - R Fuel temperature sensor (injection or supply pump assembly) Ignition switch ON 1.2 to 1.6 V
B105-9 (THW) - B104-14 (E2) G - R Water temperature sender gauge assembly Idling, ECT at 80 to 120°C (176 to 248°F) 0.2 to 1.0 V
B105-10 (THA) - B104-14 (E2) V - R Intake air temperature sensor (intake mass air flow meter sub-assembly) Idling with warm engine, IAT at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
B105-13 (VC2) - B105-14 (E21) GR - R Power source of fuel pressure sensor (common rail assembly) for PCR2 (a specific voltage) Ignition switch ON 4.75 to 5.25 V
B105-14 (E21) - Body ground R - Body ground Ground Always Below 1 Ω
B105-16 (PCR1) - B104-14 (E2) L - R Fuel pressure sensor (common rail assembly) (main) Idling (Approximately 30 MPa (306 kgf/cm2, 4351 psi)) 1.7 to 2.2 V
B105-20 (INJF) - B102-1 (E1) B - BR Injector driver Idling with warm engine Pulse generation(See waveform 8)
B105-21 (#1) - B102-1 (E1)
B105-22 (#2) - B102-1 (E1)
B105-23 (#3) - B102-1 (E1)
B105-24 (#4) - B102-1 (E1)
P - BR
LG - BR
LG - BR
GR - BR
Injector assembly Idling with warm engine Pulse generation (See waveform 9)

*1: RHD

*2: LHD

Waveform 1


a.
A428398E01
1.385,1.896 3.073,2.094 1.688,0.198 10 false 10 μs./DIV. 2.792,0.083 3.385,0.281 0.594,0.198 10 false 1 V/DIV.

CAN communication signal (Reference)

Item Content
Terminal No. (Symbols) A56-1 (CANL) - B102-1 (E1)
Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Engine stop and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




Waveform 2


a.
A428399E01
2.76,0.104 3.385,0.313 0.625,0.208 10 false 1 V/DIV. 1.385,1.906 3.073,2.104 1.688,0.198 10 false 10 μs./DIV.

CAN communication signal (Reference)

Item Content
Terminal No. (Symbols) A56-7 (CANH) - B102-1 (E1)
Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Engine stop and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




Waveform 3


a.
A256730E02
2.771,0.125 3.354,0.365 0.583,0.24 10 false 2 V/DIV. 2.979,1.208 3.385,1.427 0.406,0.219 10 false GND 1.354,1.896 3.042,2.094 1.688,0.198 10 false 20 ms./DIV.

Vehicle speed signal

Item Content
Terminal No. (Symbols) A57-7 (SPD) - B102-1 (E1)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, driving wheel slowly rotated

HINT:

The wavelength becomes shorter as the vehicle speed increases.




Waveform 4


a.
A256729E02
2.969,1 3.313,1.146 0.344,0.146 10 false GND 2.75,0.094 3.292,0.25 0.542,0.156 10 false 5 V/DIV. 1.333,1.906 2.083,2.052 0.75,0.146 10 false 20 ms./DIV.

Engine speed signal

Item Content
Terminal No. (Symbols) A57-18 (TAC) - B102-1 (E1)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.




Waveform 5


a.
A256728E03
2.76,0.115 3.302,0.313 0.542,0.198 10 false 5 V/DIV. 2.938,0.635 3.344,0.823 0.406,0.188 10 false GND 2.938,1.188 3.323,1.406 0.385,0.219 10 false GND 1.344,1.875 2.313,2.083 0.969,0.208 10 false 20 ms./DIV. 0.365,0.448 0.792,0.656 0.427,0.208 10 false (B) G 0.302,1.188 0.844,1.385 0.542,0.198 10 false (A) NE

Crankshaft position sensor signal (A)


b.

Camshaft position sensor signal (B)

Item Content
Terminal No. (Symbols) (A) B103-7 (NE+) - B103-8 (NE-)
(B) B103-13 (G+) - B103-14 (G-)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the engine speed.




Waveform 6


a.
A256733E02
2.958,1.375 3.302,1.521 0.344,0.146 10 false GND 2.719,0.073 3.25,0.229 0.531,0.156 10 false 1 V/DIV. 1.396,1.896 2.073,2.042 0.677,0.146 10 false 2 ms./DIV.

Throttle control motor signal

Item Content
Terminal No. (Symbols) B103-16 (LUSL) - B102-1 (E1)
Tool Setting 1 V/DIV., 2 ms./DIV.
Condition Accelerator pedal released → Accelerator pedal depressed (when throttle control motor is operating)

HINT:

The waveform varies depending on the throttle valve operation.




Waveform 7


a.
A256731E02
2.875,1.146 3.219,1.292 0.344,0.146 10 false GND 2.656,0.073 3.281,0.229 0.625,0.156 10 false 10 V/DIV. 1.281,1.896 1.958,2.042 0.677,0.146 10 false 5 ms./DIV.

Suction control valve signal

Item Content
Terminal No. (Symbols) B103-23 (PCV+) - B103-12 (PCV-)
Tool Setting 10 V/DIV., 5 ms./DIV.
Condition Idling

HINT:

The waveform varies depending on the suction control valve operation.




Waveform 8


a.
A256732E02
2.917,0.958 3.26,1.104 0.344,0.146 10 false GND 2.719,0.073 3.26,0.229 0.542,0.156 10 false 2 V/DIV. 1.292,1.823 2.042,1.969 0.75,0.146 10 false 20 ms./DIV.

Injector injection confirmation signal

Item Content
Terminal No. (Symbols) B105-20 (INJF) - B102-1 (E1)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.




Waveform 9


a.
A256727E03
0.24,0.538 0.651,0.722 0.411,0.184 10 (A) #1 0.24,0.899 0.651,1.083 0.411,0.184 10 (B) #3 0.24,1.271 0.651,1.455 0.411,0.184 10 (C) #4 0.24,1.62 0.651,1.804 0.411,0.184 10 (D) #2 2.929,0.551 3.268,0.701 0.34,0.15 10 GND 2.929,0.923 3.268,1.073 0.34,0.15 10 GND 2.929,1.289 3.268,1.439 0.34,0.15 10 GND 2.929,1.64 3.268,1.79 0.34,0.15 10 GND 2.696,0.056 3.238,0.208 0.542,0.152 10 5 V/DIV. 1.302,1.939 2.051,2.089 0.75,0.15 10 20 ms./DIV.

Injector assembly No. 1 injection signal (A)


b.

Injector assembly No. 3 injection signal (B)


c.

Injector assembly No. 4 injection signal (C)


d.

Injector assembly No. 2 injection signal (D)

Item Content
Terminal No. (Symbols) (A) B105-21 (#1) - B102-1 (E1)
(B) B105-23 (#3) - B102-1 (E1)
(C) B105-24 (#4) - B102-1 (E1)
(D) B105-22 (#2) - B102-1 (E1)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.