Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM D

N04C-VL ENGINE CONTROL  ECD SYSTEM  DIAGNOSIS SYSTEM  


EURO-OBD


A208456

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to the GTS. Various data output from the vehicle Engine Control Module (ECM) can then be read.

The Malfunction Indicator Light (MIL) is illuminated when the vehicle on-board computer detects a malfunction in the computer itself or in drive system components. In addition, the applicable Diagnostic Trouble Codes (DTCs) are stored in the ECM memory (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

When the malfunction does not reoccur, the MIL remains illuminated until the ignition switch is turned off, and the MIL turns off when the engine is started. Be aware that the DTCs remain stored in the ECM memory. To check DTCs, connect the GTS to the DLC3 on the vehicle.


NORMAL MODE AND CHECK MODE


The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the ability of the system to detect malfunctions, including intermittent malfunctions (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).


2 TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the subsequent drive cycle, the MIL is illuminated (2nd trip).


DLC3 (Data Link Connector 3)


A122830E76
2.333,0.573 2.052,1.042 true 2.281,1.042 2.615,0.719 true 2.385,1.656 2.823,1.74 true 1.979,1.625 2.063,1.948 true 1.76,1.042 1.406,0.677 true 1.531,1.042 1.01,0.698 true 2.323,1.469 2.51,1.625 0.188,0.156 10 false 16 2.115,1.469 2.302,1.625 0.188,0.156 10 false 15 1.906,1.469 2.094,1.625 0.188,0.156 10 false 14 1.708,1.469 1.896,1.625 0.188,0.156 10 false 13 1.5,1.469 1.688,1.625 0.188,0.156 10 false 12 1.302,1.469 1.479,1.625 0.177,0.156 10 false 11 1.094,1.469 1.281,1.625 0.188,0.156 10 false 10 0.938,1.469 1.042,1.625 0.104,0.156 10 false 9 0.938,1.042 1.042,1.198 0.104,0.156 10 false 1 1.146,1.042 1.25,1.198 0.104,0.156 10 false 2 1.354,1.042 1.458,1.198 0.104,0.156 10 false 3 1.552,1.042 1.656,1.198 0.104,0.156 10 false 4 1.76,1.042 1.865,1.198 0.104,0.156 10 false 5 1.969,1.042 2.073,1.198 0.104,0.156 10 false 6 2.167,1.042 2.271,1.198 0.104,0.156 10 false 7 2.375,1.042 2.479,1.198 0.104,0.156 10 false 8 2.146,0.406 2.563,0.635 0.417,0.229 10 false CANH 1.917,1.979 2.365,2.177 0.448,0.198 10 false CANL 2.656,0.594 2.99,0.854 0.333,0.26 10 false SIL 2.906,1.677 3.208,1.865 0.302,0.188 10 false BAT 0.833,0.521 1.094,0.708 0.26,0.188 10 false CG 1.24,0.49 1.5,0.688 0.26,0.198 10 false SG

The vehicle's ECUs use ISO 15765-4 as a communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness or connector.

Symbols (Terminal No.) Terminal Description Condition Result
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off* 6 kΩ or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.



FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


BATTERY VOLTAGE


If the voltage is below 11 V, recharge or replace the battery.

Standard voltage:

11 to 14 V



MIL


a.
A208456

The MIL illuminates when the ignition switch is turned to ON and the engine is not running.

HINT:

If the MIL is not illuminated, check the MIL circuit (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>MIL Circuit).



b.

When the engine is started, the MIL should turn off. If the MIL remains on or flashes, the diagnosis system has detected a malfunction or abnormality in the ECD system.



ALL READINESS


HINT:
·

With "All Readiness" you can check whether or not the DTC judgment has been completed by using the GTS.

·

Check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Perform the DTC judgment driving pattern to run the DTC judgement.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTCs to be confirmed.


j.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgement completed

·

System normal


ABNORMAL
·

DTC judgement completed

·

System abnormal


INCOMPLETE
·

DTC judgement not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgement

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit