Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM U

N04C-VL ENGINE CONTROL  ECD SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE CHART


If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

DTC No. Detection Item Fail-safe Operation Fail-safe Deactivation Condition
P0087 Fuel Rail / System Pressure - Too Low
[Fuel pressure sensor]
Limits engine power Ignition switch off to ON
P0088 Fuel Rail / System Pressure - Too High
[Common rail system]
Limits engine power Ignition switch off to ON
P0093 Fuel System Leak Detected - Large Leak
[Fuel leaks]
Limits engine power for 1 minute and then stalls engine Ignition switch off to ON
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
[Vacuum sensor]
Manifold absolute pressure is fixed at specified value Normal condition is restored
Limits engine power*1 Normal condition is restored*2
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input
[Vacuum sensor]
Manifold absolute pressure is fixed at specified value Normal condition is restored
Limits engine power*1 Normal condition is restored*2
P0112 Intake Air Temperature Circuit Low Input
[Intake air temperature sensor]
Intake air temperature is fixed at specified value Normal condition is restored
P0113 Intake Air Temperature Circuit High Input
[Intake air temperature sensor]
Intake air temperature is fixed at specified value Normal condition is restored
P0115 Engine Coolant Temperature Circuit
[Water temperature sender gauge]
Water temperature sender gauge output is fixed at specified value (fixed value varies depending on conditions) Normal condition is restored
P0117 Engine Coolant Temperature Circuit Low Input
[Water temperature sender gauge]
Water temperature sender gauge output is fixed at specified value (fixed value varies depending on conditions) Normal condition is restored
P0118 Engine Coolant Temperature Circuit High Input
[Water temperature sender gauge]
Water temperature sender gauge output is fixed at specified value (fixed value varies depending on conditions) Normal condition is restored
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
[Throttle position sensor]
Limits engine power Ignition switch off
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
[Throttle position sensor]
Limits engine power Ignition switch off
P0168 Fuel Temperature Too High
[Fuel temperature]
Limits engine power Normal condition is restored
P0180 Fuel Temperature Sensor "A" Circuit
[Fuel temperature sensor]
Fuel temperature is fixed at specified value Normal condition is restored
P0182 Fuel Temperature Sensor "A" Circuit Low Input
[Fuel temperature sensor]
Fuel temperature is fixed at specified value Normal condition is restored
P0183 Fuel Temperature Sensor "A" Circuit High Input
[Fuel temperature sensor]
Fuel temperature is fixed at specified value Normal condition is restored
P0190 Fuel Rail Pressure Sensor Circuit
[Fuel pressure sensor]
Limits engine power Normal condition is restored
P0191 Fuel Rail Pressure Sensor Circuit Range / Performance
[Fuel pressure sensor]
Limits engine power Normal condition is restored
P0192 Fuel Rail Pressure Sensor Circuit Low Input
[Fuel pressure sensor]
Limits engine power Normal condition is restored
P0193 Fuel Rail Pressure Sensor Circuit High Input
[Fuel pressure sensor]
Limits engine power Normal condition is restored
P0201 Injector Circuit / Open - (Cylinder 1)
[No. 1 injector]
Limits engine power Ignition switch off to ON
P0202 Injector Circuit / Open - (Cylinder 2)
[No. 2 injector]
Limits engine power Ignition switch off to ON
P0203 Injector Circuit / Open - (Cylinder 3)
[No. 3 injector]
Limits engine power Ignition switch off to ON
P0204 Injector Circuit / Open - (Cylinder 4)
[No. 4 injector]
Limits engine power Ignition switch off to ON
P0335 Crankshaft Position Sensor "A" Circuit
[Crankshaft position sensor]
Engine stopped Normal condition is restored
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance
[Throttle control motor]
Limits engine power Ignition switch off
P0500 Vehicle Speed Sensor "A"
[Vehicle speed sensor]
Vehicle speed is fixed at 0 km/h (0 mph) Normal condition is restored
P0627 Fuel Pump Control Circuit / Open
[Suction control valve]
Engine stopped Ignition switch off to ON
P062D No. 1 Fuel Injector Driver Circuit Performance
[Injector driver]
Engine stopped Ignition switch off
P1229 Fuel Pump System
[Common rail system]
Limits engine power Ignition switch off to ON
P1251 Step Motor for Turbocharger Control Circuit (Intermittent)
[Turbocharger]
Limits engine power Ignition switch off
P1674 Exhaust Brake VSV
[Exhaust brake solenoid]
Exhaust brake stop operation stopped Pass condition defected
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit
[Accelerator pedal position sensor (sensor 1)]
Limits engine power Normal condition is restored
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
[Accelerator pedal position sensor (sensor 1)]
Limits engine power Normal condition is restored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input
[Accelerator pedal position sensor (sensor 1)]
Limits engine power Normal condition is restored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input
[Accelerator pedal position sensor (sensor 1)]
Limits engine power Normal condition is restored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit
[Accelerator pedal position sensor (sensor 2)]
Limits engine power Normal condition is restored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input
[Accelerator pedal position sensor (sensor 2)]
Limits engine power Normal condition is restored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input
[Accelerator pedal position sensor (sensor 2)]
Limits engine power Normal condition is restored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation
[Accelerator pedal position sensor]
Limits engine power Normal condition is restored
P2226 Barometric Pressure Circuit
[ECM]
Atmospheric pressure is fixed at specified value Normal condition is restored
P2228 Barometric Pressure Circuit Low Input
[ECM]
Atmospheric pressure is fixed at specified value Normal condition is restored
P2229 Barometric Pressure Circuit High Input
[ECM]
Atmospheric pressure is fixed at specified value Normal condition is restored

A183106E08
2.615,0.458 2.802,0.458 false 2.802,0.458 3.208,1.51 false 6.063,0.385 6.219,0.385 false 6.219,0.385 6.396,1.615 false 0.323,1.896 0.76,2.135 0.438,0.24 10 false IG ON 3.833,1.896 4.271,2.135 0.438,0.24 10 false IG ON 0.26,2.365 0.771,2.604 0.51,0.24 10 false IG OFF 3.781,2.365 4.292,2.604 0.51,0.24 10 false IG OFF 0.344,2.719 1.24,3.26 0.896,0.542 10 false Malfunction is detected 0.781,1.188 1.948,1.5 1.167,0.313 10 false MIL starts blinking 1.646,1.708 3.031,2.094 1.385,0.385 10 false Total IG ON time 36 or 50 hours 0.542,0.385 2.698,1.031 2.156,0.646 10 false MIL remains blinking and engine output limiting control starts 1.438,2.792 3.229,3.125 1.792,0.333 10 false Idle signal is input or engine speed is 200 rpm or less 3.354,2.698 4.51,3.198 1.156,0.5 10 false Vehicle returns to normal condition 4.583,2.708 5.635,3.073 1.052,0.365 10 false Normal condition is determined 4.083,1.406 5.021,1.698 0.938,0.292 10 false MIL is blinking 3.302,3.365 5.74,3.719 2.438,0.354 10 false *2: Engine output limiting control stops 0.156,3.354 3.26,3.729 3.104,0.375 10 false *1: Engine output limiting control is being enabled 4.479,0.313 6.063,0.667 1.583,0.354 10 false MIL stays on or goes off 4.427,0.875 4.656,1.115 0.229,0.24 10 false *1 6.552,0.875 6.781,1.115 0.229,0.24 10 false *2 5.698,2.833 7,3.365 1.302,0.531 10 false Idle signal is input or engine speed is 200 rpm or less

HINT:
·

*1: The ECM will start measuring the time elapsed after the malfunction is detected at the same time the MIL starts blinking. If an idle signal is input or engine speed is 200 rpm or less after the total ignition-on time has reached 36 or 50 hours have elapsed and the MIL is still blinking, engine output will be limited to 75%.

·

*2: If an idle signal is input or engine speed is 200 rpm or less after the MIL stops blinking, the engine output limiting control will stop. After the ECM determines that the vehicle has returned to normal condition for 3 successive trips, the MIL will stop blinking. The DTC cannot be cleared using the GTS.