DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
To display the list box, press the pull down menu button next to "Primary". Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Diesel General / General data to analyze engine conditions for diesel engine
Common Rail / Fuel system related data
Common Rail (All) / Fuel system related detailed data
Diesel Throttle / Diesel throttle system related data
VN Turbo / VN turbo related data
Diesel Exhaust / Exhaust system related data
Diesel Starting / "Difficult to start" related data
Diesel Rough Idle / "Rough idle" related data
Diesel Lack of Power / "Lack of power" related data
Diesel Knocking / "Knocking" related data
Diesel Black Smoke / "Black smoke" related data
Monitor Status / Monitor status related data
Charging Control / Charging control system related data
Vehicle Information / Vehicle information
Check the values by referring to the table below.
Normal Condition: If no idling conditions are specified, the shift lever should be in neutral, and the A/C switch and all accessory switches should be off.
Diesel General
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Vehicle Speed | Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h |
Actual vehicle speed | Yes |
| Diagnostic Note:
Speed indicated on speedometer |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Idle Engine Speed | Target idle engine speed/
Min.: 0 rpm, Max.: 10000 rpm |
Idling: 600 to 700 rpm | Yes |
| Diagnostic Note:
After warming-up engine |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Speed | Engine speed/
Min.: 0 rpm, Max.: 16383 rpm |
Idling: 600 to 700 rpm | Yes |
| Diagnostic Note:
After warming-up engine |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Calculate Load | Calculated load by ECM/
Min.: 0%, Max.: 100.0% |
·
Idling: 10 to 25% ·
Running without load (2500 rpm): 7.5 to 14.5% |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Atmosphere Pressure | Atmospheric pressure value/
Min.: 0 kPa, Max.: 255 kPa |
Actual atmospheric pressure | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MAP | Absolute pressure inside intake manifold/
Min.: 0 kPa, Max.: 255 kPa |
·
Idling: 93 to 100 kPa (698 to 750 mmHg) or less ·
Engine running at 3000 rpm: 110 to 140 kPa (825 to 1050 mmHg) or more |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Coolant Temp | Engine coolant temperature/
Min.: -40°C, Max.: 140°C |
After warming up engine: 80 to 100°C (176 to 212°F) | Yes |
| Diagnostic Note:
If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Intake Air | Intake air temperature/
Min.: -40°C, Max.: 140°C |
Equivalent to temperature at intake manifold | Yes |
| Diagnostic Note:
If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Run Time | Engine run time/
Min.: 0 s Max.: 65535 s |
Time after engine started | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Initial Engine Coolant Temp | Initial engine coolant temperature/
Min.: -40°C, Max.: 120.0°C |
Engine coolant temperature when engine starts | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Initial Intake Air Temp | Initial intake air temperature/
Min.: -40°C, Max.: 120.0°C |
Intake air temperature when engine starts | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Battery Voltage | Battery voltage/
Min.: 0 V Max.: 65.5 V |
Idling: 11 to 14 V | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Pre Glow | Pre glow operation/
OFF or ON |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| After Glow | After glow operation/
OFF or ON |
- | Yes |
All Data 1
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Position | Accelerator position status/
Min.: 0%, Max.: 99.60% |
·
Accelerator pedal released: 0% ·
Accelerator pedal depressed: 68 to 99.6% |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sens. No.1 Volt % | Accelerator position No. 1/
Min.: 0%, Max.: 100.0% |
·
Accelerator pedal released: 12 to 20% ·
Accelerator pedal depressed: 56 to 72% |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sens. No.2 Volt % | Accelerator position No. 2/
Min.: 0%, Max.: 100.0% |
·
Accelerator pedal released: 28 to 36% ·
Accelerator pedal depressed: 72 to 88% |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sensor Out No.1 | Accelerator position No. 1 voltage/
Min.: 0 V, Max.: 4.9 V |
·
Accelerator pedal released: 0.6 to 1.0 V ·
Accelerator pedal fully depressed: 2.8 to 3.6 V |
No |
| Diagnostic Note:
Read value with ignition switch to ON (Do not start engine) |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Accel Sensor Out No.2 | Accelerator position No. 2 voltage/
Min.: 0 V, Max.: 4.9 V |
·
Accelerator pedal released: 1.4 to 1.8 V ·
Accelerator pedal fully depressed: 3.6 to 4.4 V |
No |
| Diagnostic Note:
Read value with ignition switch to ON (Do not start engine) |
|||
Diesel Throttle
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Throttle Position | Target throttle position/
Min.: -128%, Max.: 127% |
·
Throttle valve fully opened: 0% ·
Throttle valve fully closed: 100% |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Actual Throttle position | Actual throttle position/
Min.: -128%, Max.: 127% |
Idling after warmed-up engine: 81 to 95% | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Close Learning Val. | Throttle valve fully closed/
Min.: 0 deg, Max.: 84.0 deg |
- | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Diesel Throttle Learn Status | Diesel throttle learning status/
NG or OK |
OK | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Sensor Volt % | Throttle position sensor output voltage/
Min.: 0%, Max.: 100.0% |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Throttle Motor DUTY | Throttle actuator duty/
Min.: 0%, Max.: 100.0% |
Idling after warming up engine: 30 to 100% | Yes |
Common Rail (All)
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Volume | Injection volume/
Min.: 0 mm3/st, Max.: 1279.98 mm3/st |
Idling: 5.0 to 15.0 mm3/st | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Inj. FB Vol. for Idle | Idle stable control/
Min.: -80.00 mm3/st, Max.: 79.99 mm3/st |
-10 to 10 mm3/st | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Inj Vol Feedback Learning | Injection volume feedback learning value/
Min.: -10.0 mm3/st, Max.: 9.9 mm3/st |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Feedback Val #1 | Injection volume correction for cylinder 1/
Min.: -10.0 mm3/st, Max.: 10.0 mm3/st |
Idling: -7.0 to 7.0 mm3/st | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Feedback Val #2 | Injection volume correction for cylinder 2/
Min.: -10.0 mm3/st, Max.: 10.0 mm3/st |
Idling: -7.0 to 7.0 mm3/st | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Feedback Val #3 | Injection volume correction for cylinder 3/
Min.: -10.0 mm3/st, Max.: 10.0 mm3/st |
Idling: -7.0 to 7.0 mm3/st | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Feedback Val #4 | Injection volume correction for cylinder 4/
Min.: -10.0 mm3/st, Max.: 10.0 mm3/st |
Idling: -7.0 to 7.0 mm3/st | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Pilot 1 Injection Period | Pilot 1 Injection period/
Min.: 0 μs, Max.: 65535 μs |
Idling after warming up engine: 0 μs | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Pilot 2 Injection Period | Pilot 2 Injection period/
Min.: 0 μs, Max.: 65535 μs |
Idling: 0 to 600 μs | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Main Injection Period | Main Injection period/
Min.: 0 μs, Max.: 65535 μs |
Idling: 600 to 1000 μs | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| After Injection Period | After Injection period/
Min.: 0 μs, Max.: 65535 μs |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Pilot 1 Injection Timing | Pilot 1 Injection timing/
Min.: -70.0 deg(CA), Max.: 20.0 deg(CA) |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Pilot 2 Injection Timing | Pilot 2 Injection timing/
Min.: -50.0 deg(CA), Max.: 20.0 deg(CA) |
Idling: -8 to -6°CA | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Main Injection Timing | Main Injection timing/
Min.: -90.0 deg(CA), Max.: 90.0 deg(CA) |
Idling: -1 to 1°CA | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| After Injection Timing | After Injection timing/
Min.: -10.0 deg(CA), Max.: 50.0 deg(CA) |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injector Memory Error | Injector Memory Error/
No Error or Error |
No Error | Yes |
| Diagnostic Note:
If the injector compensation codes are not input into the new ECM, or if an injector compensation code of a different injector model or a compensation code representing a value which exceeds the compensation setting range is input into the new ECM, DTC P062F is stored and "Injector Memory Error" displays "Error". |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Pressure Correction | Injection pressure correction/
Min.: -500.0 mm3/st, Max.: 779.9 mm3/st |
-400 to 400 mm3/st | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Common Rail Pressure | Target common rail pressure/
Min.: 0 kPa, Max.: 655350 kPa |
Idling: 25000 to 35000 kPa | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Press | Fuel pressure/
Min.: 0 kPa, Max.: 655350 kPa |
Idling: 25000 to 35000 kPa | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Common Rail Pres Sens 2 | Fuel pressure/
Min.: 0 kPa, Max.: 655350 kPa |
Idling: 25000 to 35000 kPa | No |
| Diagnostic Note:
This is a backup output value from the fuel pressure sensor. |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Temperature | Fuel temperature/
Min.: -40°C, Max.: 215°C |
Actual fuel temperature | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Fuel Return Temp | Fuel return temperature/
Min.: -40°C, Max.: 215°C |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Pump SCV Current | Pump open current value/
Min.: 0 mA, Max.: 8191.8 mA |
Idling: 1350 to 2200 mA | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Pump SCV Learning Value | Pump current learning value/
Min.: -4096.0 mA, Max.: 4095.8 mA |
- | Yes |
All Data 2
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| VN Turbo Type | VN turbo type/
Not Avl, Commo, Vacuum, CAN Com or DC |
- | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Exhaust Brake Switch | Exhaust brake switch status/
OFF or ON |
Exhaust brake operated: ON | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Starter Signal | Starter signal/
OFF or ON |
Cranking: ON | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| IG SW | Ignition switch status/
OFF or ON |
·
Ignition switch ON: ON ·
Ignition switch off: OFF |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Clutch Switch | Exhaust retarder switch status/
OFF or ON |
Exhaust retarder switch on: ON | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Reverse Switch | Reverse switch status/
OFF or ON |
·
Shift lever in reverse: ON ·
Shift lever not in reverse: OFF |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Stop Light Switch | Stop light switch status/
OFF or ON |
·
Brake pedal depressed: ON ·
Brake pedal released: OFF |
Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| A/C Signal | Air conditioning signal/
OFF or ON |
Air conditioning operated: ON | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Stop SW | Engine stop switch status/
OFF or ON |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Check Mode | Check mode/
OFF or ON |
Check mode on: ON | No |
| Diagnostic Note:
(Click here( ))
|
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| SPD Test Result | Check mode result for vehicle speed sensor/
Compl or Incmpl |
Compl | No |
Monitor Status
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Complete Parts Monitor | Comprehensive component monitor/
Not Avl or Avail |
*1 | No |
| Fuel System Monitor | Fuel system monitor/
Not Avl or Avail |
*1 | No |
| Misfire Monitor | Misfire monitor/
Not Avl or Avail |
*1 | No |
| EGR/VVT Monitor | EGR/VVT monitor/
Not Avl or Avail |
*1 | No |
| EGR/VVT Monitor | EGR/VVT monitor/
Compl or Incmpl |
*1 | No |
| O2S(A/FS) Heater Monitor | O2S(A/FS) heater monitor/
Not Avl or Avail |
*1 | No |
| O2S(A/FS) Heater Monitor | O2S(A/FS) heater monitor/
Compl or Incmpl |
*1 | No |
| O2S(A/FS) Monitor | O2S(A/FS) monitor/
Not Avl or Avail |
*1 | No |
| O2S(A/FS) Monitor | O2S(A/FS) monitor/
Compl or Incmpl |
*1 | No |
| A/C Monitor | A/C monitor/
Not Avl or Avail |
*1 | No |
| A/C Monitor | A/C monitor/
Compl or Incmpl |
*1 | No |
| 2nd Air Monitor | 2nd air monitor/
Not Avl or Avail |
*1 | No |
| 2nd Air Monitor | 2nd air monitor/
Compl or Incmpl |
*1 | No |
| EVAP Monitor | EVAP monitor/
Not Avl or Avail |
*1 | No |
| EVAP Monitor | EVAP monitor/
Compl or Incmpl |
*1 | No |
| Heated Catalyst Monitor | Heated catalyst monitor/
Not Avl or Avail |
*1 | No |
| Heated Catalyst Monitor | Heated catalyst monitor/
Compl or Incmpl |
*1 | No |
| Catalyst Monitor | Catalyst monitor/
Not Avl or Avail |
*1 | No |
| Catalyst Monitor | Catalyst monitor/
Compl or Incmpl |
*1 | No |
| *1:
Not Avl: The monitor is not available on the vehicle. Avail: The monitor is available on the vehicle. Compl / Incmpl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected. |
|||
All Data 3
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| # Codes (Include History) | Number of codes/
Min.: 0, Max.: 255 |
- | No |
| Diagnostic Note:
Number of detected DTCs |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MIL | MIL status/
OFF or ON |
MIL on: ON | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Time after DTC Cleared | Time after DTC cleared/
Min.: 0 min, Max.: 65535 min |
Equivalent to time after DTCs cleared | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Distance from DTC Cleared | Distance after DTC cleared/
Min.: 0 km, Max.: 65535 km |
Equivalent to drive distance after DTCs cleared | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Warmup Cycle Cleared DTC | Warm up cycle after DTC cleared/
Min.: 0, Max.: 255 |
- | Yes |
| Diagnostic Note:
Number of warm up cycles after DTC cleared |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Number of Emission DTC | Number of emission DTC/
Min.: 0, Max.: 127 |
- | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| TC and TE1 | TC and TE1 terminals of DLC3/
OFF or ON |
- | Yes |
Diesel Starting
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Start Time | Engine start time/
Min.: 0 ms, Max.: 267000 ms |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Speed (Starter Off) | Engine speed when starter off/
Min.: 0 rpm, Max.: 1593 rpm |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Starter Count | Starter on count/
Min.: 0, Max.: 255 |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Run Dist of Previous Trip | Distance driven during previous trip/
Min.: 0 km, Max.: 326 km |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Glow Request Lighting Time | Glow request lighting time/
Min.: 0 ms, Max.: 33423 ms |
- | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| IG-ON Time | Ignition switch ON time before engine start/
Min.: 0 ms, Max.: 33423 ms |
- | Yes |
Diesel Lack of Power
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MAF Low | Mass air flow low/
OFF or ON |
OFF | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Boost Pressure Low | Boost pressure low/
OFF or ON |
OFF | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Common Rail Pressure Low | Common rail pressure low/
OFF or ON |
OFF | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Coolant Temp High | Engine coolant temperature high/
OFF or ON |
OFF | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| MAF/Estimate MAF Ratio | Indicates the ratio of estimated intake air volume and actual intake air volume/
Min.: 0, Max.: 2.55 |
- | Yes |
All Data 4
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Warm Up Switch | Warm up switch status/
OFF or ON |
Warm up switch on: ON | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| ACT VSV | Air conditioning cut signal/
OFF or ON |
- | Yes |
Vehicle Information
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Model Code | Model Code | - | No |
| Diagnostic Note:
Identifying model code: XZB## |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Type | Engine type | - | No |
| Diagnostic Note:
Identifying engine type: N04CVL |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Cylinder Number | Identifying cylinder number/
Min.: 0, Max.: 255 |
- | No |
| Diagnostic Note:
Identifying cylinder number: 4 |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Destination | Destination | - | No |
| Diagnostic Note:
Identifying destination: V |
|||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Model Year | Identifying model year/
Min.: 1900, Max.: 2155 |
- | No |
| Diagnostic Note:
Identifying model year: 20## |
|||
All Data 5
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Engine Speed | Target engine speed/
Min.: 0 rpm, Max.: 5000 rpm |
Idling: 600 to 700 rpm | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Target Common Rail Press | Target common rail pressure/
Min.: 0 MPa, Max.: 255 MPa |
Idling: 30 to 32 MPa | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Pump Mode | Injection or supply pump assembly control mode/
PCV, DUTY, Normal, IG OFF or STOP |
- | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Injection Pump Learning Status | Injection or supply pump assembly learning status/
Incmpl or Compl |
Compl | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| PCV Open Duty | Suction control valve open duty/
Min.: 0% Max.: 100.0% |
45 to 55% | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| PCV Open Current FB Val | Suction control valve open current feedback volume/
Min.: -6000 mA, Max.: 6000 mA |
-400 to 400 mA | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Engine Overspeed History | Engine overspeed history/
OFF or ON |
OFF | No |
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Notes |
|---|---|---|---|
| Control the A/C Cut Signal | Control the air conditioning cut signal | OFF / ON | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped |
| Connect the TC and TE1 | Turn on TC and TE1 connection | OFF / ON | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped |
| Diesel Throttle Target Angle | Control the diesel throttle valve | 0 to 90% | Test possible when following conditions met:
·
Ignition switch ON ·
Engine stopped |
| Test the Fuel Leak | Increase common rail internal fuel pressure, and checks for fuel leaks | Stop / Start | ·
Fuel pressure inside common rail increased to specified value and engine speed increased to 2000 rpm when Start is selected ·
Above conditions preserved while test is Start Test possible when following conditions met: ·
Engine idling ·
Vehicle stopped |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | OFF / ON | Fuel injection is stopped while the test is ON.
·
Confirm that the vehicle is stopped and the engine is idling. ·
If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning. |
| Activate the VSV for Exhaust Brake | Activate the solenoid valve for exhaust brake | OFF / ON | Test possible when following conditions met:
·
Engine idling ·
Vehicle stopped |