Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM C

N04C-VL ENGINE CONTROL  ECD SYSTEM  P0560  System Voltage  


DESCRIPTION

While the ignition switch is off, battery voltage is supplied to terminal BATT of the ECM for storing DTCs and fuel injection feedback learning values.

DTC No. DTC Detection Condition Trouble Area
P0560 Condition (a) or (b) continues (1 trip detection logic):
(a) Significant decrease in battery voltage
(b) Open in back-up power source circuit
·

Open in back-up power source circuit

·

Low battery voltage

·

ECM



HINT:

If DTC P0560 appears, the ECM does not store other DTCs.


WIRING DIAGRAM

A398545E05
0.688,0.99 1.333,1.177 0.646,0.188 10 false FL MAIN 1.229,0.656 3.26,1.094 2.031,0.438 10 false R/B NO. 2-B 2.802,0.667 3.073,0.844 0.271,0.177 10 false P/I 3.885,0.656 4.563,0.854 0.677,0.198 10 false EFI-MAIN 1.323,1.948 2,2.146 0.677,0.198 10 false Battery 5.344,1.354 5.771,1.531 0.427,0.177 10 false B102 5.385,0.479 5.729,0.656 0.344,0.177 10 false A57 5.792,0.365 6.198,0.531 0.406,0.167 10 false BATT 5.813,1.354 6.063,1.531 0.25,0.177 10 false E1 6.167,2.052 6.563,2.24 0.396,0.188 10 false ECM 5.438,0.271 5.604,0.448 0.167,0.177 10 false 23 5.458,1.167 5.625,1.344 0.167,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.



PROCEDURE

1.CHECK ECM (BATT VOLTAGE)
a.
A257471E12
0.198,0.604 0.583,0.844 0.385,0.24 0.271,1.604 0.99,1.51 false 1.042,1.417 1.708,1.573 0.667,0.156 10 false 23 (BATT) 0.271,0.646 1.104,0.948 0.833,0.302 10 false A57 0.042,0.052 0.208,0.208 0.167,0.156 10 false *a

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-23 (BATT) - Body ground Always 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-23 (BATT) - Positive (+) battery terminal Always Below 1 Ω
A57-23 (BATT) or Positive (+) battery terminal - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BATTERY)

3.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE BATTERY