Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM2850E _58 Vehicle Interior _073141 METER / GAUGE / DISPLAY _0357098 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit provides power to the combination meter assembly.

WIRING DIAGRAM

E200578E02
5.281,3.354 7.115,3.531 1.833,0.177 10 false Combination Meter Assembly 5.281,3.188 5.552,3.365 0.271,0.177 10 false J1 5.417,2.125 5.688,2.313 0.271,0.188 10 false 21 5.5,1.24 5.656,1.417 0.156,0.177 10 false 2 5.5,0.563 5.656,0.74 0.156,0.177 10 false 1 5.75,0.698 5.906,0.875 0.156,0.177 10 false B 5.771,1.375 6.021,1.552 0.25,0.177 10 false IG+ 5.75,2.25 5.99,2.427 0.24,0.177 10 false ES 3.531,0.823 3.969,1 0.438,0.177 10 false DOME 3.427,1.542 4.458,1.719 1.031,0.177 10 false METER IG2 0.865,0.656 1.635,0.833 0.771,0.177 10 false from Battery 0.354,1.354 1.854,1.542 1.5,0.188 10 false from IG2 NO.2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E199460E05
0.281,1.083 0.708,1.375 0.427,0.292 1,1.281 0.75,0.802 0.75,0.802 0.583,0.802 true 1.115,1.271 1.219,0.656 1.219,0.656 1.385,0.656 true 1.01,1.438 0.833,1.781 0.833,1.781 0.667,1.781 true 0.188,0.115 0.354,0.292 0.167,0.177 10 false *1 0.427,1.146 0.719,1.375 0.292,0.229 10 false J1 0.406,0.729 0.563,0.906 0.156,0.177 10 false B 1.479,0.583 1.729,0.76 0.25,0.177 10 false IG+ 0.427,1.708 0.708,1.927 0.281,0.219 10 false ES

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J1-2 (IG+) - Body ground Ignition switch ON 11 to 14 V
J1-1 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-21 (ES) - Body ground Always Below 1 Ω


Text in Illustration
*1 Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR