Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 2 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357115 AIRBAG SYSTEM(for 2 Connectors Type) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 2 Connectors Type)  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are communicated through SRS warning light blinking patterns.

WIRING DIAGRAM

C377031E01
0.677,2.302 1.135,2.5 0.458,0.198 10 false J45 0.667,2.51 1.125,2.708 0.458,0.198 10 false DLC3 1.542,1.135 2,1.333 0.458,0.198 10 false TC 1.552,1.938 2.01,2.135 0.458,0.198 10 false CG 1.854,1.031 2.177,1.24 0.323,0.208 10 false 13 1.875,1.802 2.125,1.99 0.25,0.188 10 false 4 5.5,1.042 5.854,1.24 0.354,0.198 10 false 15 5.563,2.573 5.917,2.771 0.354,0.198 10 false A58 5.792,1.125 6.146,1.323 0.354,0.198 10 false TC 5.552,2.76 7.073,2.969 1.521,0.208 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)



HINT:

When one or more of the warning lights blinks continuously, the cause may be a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - AIRBAG ECU ASSEMBLY AND BODY GROUND)
C373330E01
1.76,0.24 2.167,0.479 0.406,0.24 4.688,0.052 5.094,0.292 0.406,0.24 4.094,1.448 4.271,1.448 4.271,1.448 4.917,0.927 true 2.479,1.479 2.302,1.479 2.302,1.479 2.042,1.135 true 1.052,1.302 1.188,1.302 1.188,1.302 1.875,0.833 true 0.625,0.156 0.938,0.354 0.313,0.198 10 false *a 1.854,0.271 2.219,0.469 0.365,0.198 10 false J45 0.604,1.198 1.146,1.406 0.542,0.208 10 false 4 (CG) 2.49,1.396 3.031,1.604 0.542,0.208 10 false 13 (TC) 4.76,0.083 5.177,0.281 0.417,0.198 10 false A58 3.635,1.365 4.229,1.573 0.594,0.208 10 false 15 (TC) 3.771,0.177 4.083,0.375 0.313,0.198 10 false *b

Text in Illustration
*a Front view of DLC3 *b Rear view of wire harness connector
(to Airbag ECU Assembly)

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the airbag ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-13 (TC) - A58-15 (TC) Always Below 1 Ω
J45-4 (CG) - Body ground Always Below 1 Ω
A58-15 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE HARNESS AND CONNECTOR