Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 3 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357116 AIRBAG SYSTEM(for 3 Connectors Type) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 3 Connectors Type)  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C372577E01
0.229,0.333 1.083,0.75 0.854,0.417 10 false from IG2-NO.2 Relay 1.594,0.938 2.385,1.125 0.792,0.188 10 false METER-IG2 1.625,0.49 2.417,0.677 0.792,0.188 10 false A/BAG-IG2 0.604,2.542 2.438,2.719 1.833,0.177 10 false : CAN Communication Line 2.292,2.333 4.333,2.521 2.042,0.188 10 false Combination Meter Assembly 5.281,2.354 6.896,2.563 1.615,0.208 10 false Airbag ECU Assembly 2.51,0.781 2.885,0.979 0.375,0.198 10 false IG+ 2.51,1.865 2.885,2.063 0.375,0.198 10 false ES 2.281,0.688 2.531,0.875 0.25,0.188 10 false 2 2.208,1.771 2.51,1.969 0.302,0.198 10 false 21 2.302,2.167 2.604,2.365 0.302,0.198 10 false J1 5.302,0.219 5.604,0.417 0.302,0.198 10 false 21 5.323,1.406 5.625,1.604 0.302,0.198 10 false 25 5.323,1.74 5.625,1.938 0.302,0.198 10 false 26 5.271,2.146 5.677,2.344 0.406,0.198 10 false A58 5.594,0.375 5.969,0.573 0.375,0.198 10 false IG2 5.594,1.531 5.969,1.729 0.375,0.198 10 false E1 5.594,1.875 5.969,2.073 0.375,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Result Proceed to
DTC is not output A
DTCs are output B



A

2.CHECK BATTERY

B

2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF CONNECTORS

NG

REPLACE OR RECHARGE BATTERY

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag ECU assembly and combination meter assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY)
a.
C198548E22
1.438,0.167 1.865,0.406 0.427,0.24 1.031,1.885 1.271,1.885 1.271,1.885 1.708,1.396 true 2.615,1.854 2.396,1.854 2.396,1.854 2.198,1.385 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.521,0.208 1.885,0.406 0.365,0.198 10 false A58 0.552,1.781 1.219,1.99 0.667,0.208 10 false 25 (E1) 2.625,1.781 3.292,1.99 0.667,0.208 10 false 21 (IG2)

Disconnect the connectors from the airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A58-21 (IG2) - A58-25 (E1) Ignition switch ON 11 to 14 V
A58-21 (IG2) - A58-26 (E2) Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Airbag ECU Assembly)


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C287546E01
1.646,0.49 2.052,0.74 0.406,0.25 0.625,0.583 0.49,0.583 0.49,0.583 0.885,1.26 true 0.781,1.479 0.969,1.948 0.969,1.948 1.115,1.948 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.677,0.49 1.24,0.677 0.563,0.188 10 false 2 (IG+) 1.146,1.865 1.75,2.042 0.604,0.177 10 false 21 (ES) 1.781,0.531 2.083,0.708 0.302,0.177 10 false J1

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Disconnect the connector from the combination meter assembly.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J1-39 (IG+) - J1-21 (ET) Ignition switch ON 11 to 14 V
J1-40 (B) - J1-21 (ET) Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter assembly.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG