There are left and right matchmarks on the rear end of the torsion bar springs.
Be careful not to interchange them.
48162
1. APPLY GREASE TO SPINE OF TORSION BAR SPRING
Install the boot.
Apply MP grease to the spline of the torsion bar Spring.
2.INSTALL TORSION BAR SPRING AND ADJUST VEHICLE HEIGHT
If Using a New Torsion Bar Spring:
Align the matchmarks and install the torsion bar spring to the torque arm.
Align the matchmarks and install the anchor arm to the torsion bar spring.
Install the boot to the anchor arm.
Tighten the adjusting nut so that the bolt protrusion "A" is equal to that before removal.
Install the front wheel and lower the vehicle.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>INSTALLATION
Bounce the vehicle up and down several times to allow the suspention to settle.
Adjust the vehicle height by turning the adjusting nut.
for 1BZ-FPE:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 1BZ-FPE)>ADJUSTMENT
for 1HZ:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 1HZ)>ADJUSTMENT
for 14B:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 14B)>ADJUSTMENT
for 2TR-FE:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 2TR-FE)>ADJUSTMENT
for N04C-UH, N04C-VL, N04C-VQ:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for N04C-UH, N04C-VL, N04C-VQ)>ADJUSTMENT
If Using a New Torsion Bar Spring:
Install the torsion bar spring to the torque arm.
Install the anchor arm to the torsion bar spring.
Connect the adjusting bolt to the anchor arm with the adjusting seat and nut.
Tighten the adjusting nut by hand until there is no play in the ancher arm adjuster seat.
Measure the protruding bolt end "B".
-8 - +12 mm (-0.32 - +0.48 in.)
It the bolt protrusion "B" is not to specification, reinstall the anchor arm to the torsion bar spring.
Place matchmarks on the adjusting seat, bolt and nut.
If the bolt protrusion "B" is - values, as shown in the illustration of balloon.
Tighten the adjusting nut so that nut revolution "C" is as detailed below.
| For Hong Kong
For Australia (Long body) |
23 turns |
| Others (Short body besides
Tire size 7.00R16) |
21 turns |
| Others | 18 turns |
Install tha front wheel and lower the vehicle.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL>INSTALLATION
Bounce the vehicle up and down several times to allow the suspension to settle.
Adjust the vehicle height by turning the adjusting nut.
for 1BZ-FPE:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 1BZ-FPE)>ADJUSTMENT
for 1HZ:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 1HZ)>ADJUSTMENT
for 14B:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 14B)>ADJUSTMENT
for 2TR-FE:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for 2TR-FE)>ADJUSTMENT
for N04C-UH, N04C-VL, N04C-VQ:Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT (for N04C-UH, N04C-VL, N04C-VQ)>ADJUSTMENT
3.INSTALL LOCK NUT
100 N*m (1,000 kgf*cm, 74 ft.*lbf)