Home › Engine / Hybrid System › 1BZ-FPE (ENGINE CONTROL) › ELECTRONIC CONTROLLED CARBURETOR SYSTEM › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073136 1BZ-FPE ENGINE CONTROL _0355837 ELECTRONIC CONTROLLED CARBURETOR SYSTEM D

1BZ-FPE ENGINE CONTROL  ELECTRONIC CONTROLLED CARBURETOR SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


F102324

·

When troubleshooting Multiplex OBD (M-OBD) vehicles, the only difference from the usual troubleshooting procedure is that you connect the hand-held tester to the vehicle, and read off various data output from the vehicle's engine ECU.

·

The vehicle's on-board computer lights up the check engine warning light (CHK ENG) on the instrument panel when the computer detects a malfunction in the computer itself or in drive systemcomponents. In addition to the check engine warning light lighting up when a malfunction is detected, the applicable Diagnosis Trouble Code (DTC) are recorded in the engine ECU memory (Click hereEngine / Hybrid System>1BZ-FPE (ENGINE CONTROL)>ELECTRONIC CONTROLLED CARBURETOR SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).



If the malfunction has been repaired, the check engine warning light goes off automatially but the DTCs remain recorded in the engine ECU memory.

A420117

·

To check the DTCs, connect the hand-held tester to Data Link Connector 3 (DLC3) on the vehicle. or read the number of blinks of the check engine warning light when TC and CG terminals on the DLC3 are connected. The hand-held tester also enables you to erase the DTCs and activate the several actuaters and check freezed frame data and vaious forms of engine data (For operating instructions, see the hand-held tester instruction book).

·

The diagnosis system operates in normal mode during normal vehicle use. It also has a check (test) mode for technicans to simulate malfunction symptoms and troubleshoot. Most DTCs use 2 trip detection logic to prevent erroneous detection and ensure thorough malfunction detection. By switching the engine ECU to check (test) mode using hand-held tester when troubleshooting, the techinician can cause the check engine warning (CHK ENG) to light up for a malfunction that is only detected once or momentarily. (Hand-held tester only) (Click hereEngine / Hybrid System>1BZ-FPE (ENGINE CONTROL)>ELECTRONIC CONTROLLED CARBURETOR SYSTEM>CHECK MODE PROCEDURE).

·

* 2 trip detection logic

When a logic malfunction is fist detected, the malfunction is temporaily stored in the engine ECU memory. If the same malfunction is detected again during the second drive test, this second detection cases the check engine warning (CHK ENG) to light up.

The 2 trip repeats the same mode for 2 times. (However, the IG switch must be turned OFF between the 1st trip and 2nd trip)

·

Freeze frame data:

Freeze frame data records the engine condition when malfunction is detected.

Because freeze frame data records the engine conditions (fuel system, calculator load, water temperature, fuel trim, engine speed, vehicle speed, etc.) when the malfunction is detected, when troubleshooting it is useful for determining whether the vehicle was running or stopped, the engine warmed up or not, the air-fuel ratio lean or rich, etc. at the time of the malfunction.


CHECK THE DLC3


A004550

The vehicle's engine ECU uses the ISO 14230 for communication. The terminal arrangement of DLC3 complies with SAE J1962 and matches the ISO 14230 format.

Terminal No. Connection / Voltage or Resistance Condition
7 Bus "+" Line / Pulse generation During transmission
4 Chassis Ground / - Body Ground 1 Ω or less Always
16 Battery Positive / - Body Ground 9 to 14 V Always

HINT:

If your display shows "UNABLE TO CONNECT TO VEHICLE" when you have connected the cable of the hand-held tester to DLC3, turned the ignition switch ON and operated the hand-held tester, there is a problem on the vehicle side or tool side.


a.

If communication is normal when the tool is connected to another vehicle, inspect DLC3 on the original vehicle.


b.

If communication is still not possible is when the tool is connected to another vehicle, the problem is probably in the tool itself, so consult the Service deparment listed in the tool,s instruction manual.