Home › Engine / Hybrid System › 14B (ENGINE MECHANICAL) › TIMING GEAR › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073170 14B ENGINE MECHANICAL _0356052 TIMING GEAR A

14B ENGINE MECHANICAL  TIMING GEAR  TIMING GEARS AND CAMSHAFT INSPECTION  


PROCEDURE

Hide 1.INSPECT CAMSHAFT

a.
A430606

Inspect camshaft for runout

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.06 mm (0.0024 in.)


If the circle runout is greater than maximum, replace the camshaft.



b.

Inspect cam lobes

i.
A430607

Using a micrometer, measure the cam lobe height.

Standard cam lobe height

Intake:
3B 45.288 - 45.378 mm (1.7830 - 1.7865 in.)
14B 44.879 - 44.969 mm (1.7669 - 1.7704 in.)
15B-F, 15B-FT 43.774 - 43.864 mm (1.7234 - 1.7269 in.)


Exhaust:
3B 45.261 - 45.351 mm (1.7819 - 1.7855 in.)
14B 45.050 - 45.140 mm (1.7736 - 1.7772 in.)
15B-F, 15B-FT 44.905 - 44.995 mm (1.7679 - 1.7715 in.)


Minimum cam lobe height

Intake:
3B 44.85 mm (1.7657 in.)
14B 44.44 mm (1.7496 in.)
15B-F, 15B-FT 43.34 mm (1.7063 in.)


Exhaust:

If the cam lobe height is less than minimum, replace the camshaft.

3B 44.83 mm (1.7850 in.)
14B 44.62 mm (1.7567 in.)
15B-F, 15B-FT 44.47 mm (1.7508 in.)




c.
A430608

Inspect camshaft journals

i.

Using a micrometer, measure the journal diameter.

Journal diameter (from front side):

If the journal diameter is not within specification, check the oil clearance.

No.1 53.459 - 53.475 mm (2.1047 - 2.1053 in.)
No.2 53.209 - 53.225 mm (2.0948 - 2.0955 in.)
No.3 52.959 - 52.975 mm (2.0850 - 2.0856 in.)
No.4 52.709 - 52.725 mm (2.0752 - 2.0758 in.)
No.5 52.459 - 52.475 mm (2.0653 - 2.0659 in.)




d.
A430609

Inspect camshaft thrust clearance

i.

Using a feeler gauge, measure the thrust clearance between the camshaft and thrust plate.

Standard clearance:

0.060 - 0.130 mm (0.0024 - 0.0051 in.)


Maximum clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is greater than maximum, replace the thrust plate. If necessary, replace the camshaft.

Click hereEngine / Hybrid System>14B (ENGINE MECHANICAL)>TIMING GEAR>REPLACEMENT OF CAMSHAFT (OR CAMSHAFT TIMING GEAR)



Hide 2.INSPECT IDLER GEAR

a.
A430610

Using a cylinder gauge, measure the inside diameter of the idler gear.

Idler gear inside diameter:

44.974 - 45.000 mm (1.7706 - 1.7717 in.)



b.
A430611

Using a micrometer, measure the diameter of the idler gear shaft.

Idler gear shaft diameter:

44.935 - 44.955 mm (1.7691 - 1.7699 in.)



c.

Subtract the idler gear shaft diameter measurement from the idler gear inside diameter measurement.

Standard oil clearance:

0.019 - 0.065 mm (0.0007 - 0.0026 in.)


Maximum oil clearance:

0.18 mm (0.0071 in.)


If the clearance is greater than maximum, replace the gear and shaft.


Hide 3.INSPECT INJECTION PUMP DRIVE GEAR

a.
A430612

Check that bearing is not rough or worn.