Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT (for 1BZ-FPE) › 2018.07–2019.08
RM2850E _53 Suspension _073183 ALIGNMENT / HANDLING DIAGNOSIS _0356121 FRONT WHEEL ALIGNMENT(for 1BZ-FPE) N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT(for 1BZ-FPE)  ADJUSTMENT  


PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT

a.
C376376E01
0.063,0.104 0.438,0.344 0.375,0.24 12 false *A 0.115,2.375 0.49,2.615 0.375,0.24 12 false *B 0.646,1.635 1.021,1.875 0.375,0.24 10 false A 0.385,3.865 0.76,4.104 0.375,0.24 10 false B

Bounce the vehicle up and down at the corners to stabilize the suspension and measure the vehicle height.

Measuring points:
Front Side A:

Ground clearance of lower arm front side cam bolt front center

Rear Side B:

Ground clearance of rear leaf spring front side bolt center


Text in Illustration
*A for Front Side
*B for Rear Side

Standard Vehicle Height (Unloaded Vehicle):
Vehicle Model Front Side A Rear Side B
(Reference)
BZB70R-ZCMSC5 262 mm
(10.31 in.)
326 mm
(12.83 in.)


NOTICE:

Before inspecting the wheel alignment, check the vehicle height.



Hide 3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

a.
C132440E42
2.083,1.01 2.427,0.458 2.427,0.458 2.594,0.458 true 0.792,1.031 0.938,1.031 0.938,1.031 0.938,1.573 true 0.615,0.948 1,1.26 0.385,0.313 10 false *b 2.635,0.365 3.156,0.604 0.521,0.24 10 false *a

Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.

Text in Illustration
*a Camber-caster-kingpin Gauge
*b Turning Radius Gauge

i.

w/ Wheel Cap:

Remove the wheel cap.


ii.

Remove the front axle hub grease cap.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


iii.

Remove the cotter pin and lock cap.


iv.

Align the end of the camber-caster-kingpin gauge center rod to the middle of the spindle and install the front axle hub to the camber-caster-kingpin gauge.

NOTICE:

Take care not to apply grease to the camber-caster-kingpin gauge.




b.

Inspect the camber, caster and steering axis inclination.

Camber, caster and steering axis inclination (Unloaded Vehicle):
Camber Caster Steering Axis Inclination
(Reference)
0°00' +/- 30'
(0.0° +/- 0.5°)
4°30' +/- 30'
(4.5° +/- 0.5°)
13°00'
(13.0°)


NOTICE:
·

Perform the inspection while the vehicle is empty.

·

The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both the camber and caster.

·

Remove any garbage and foreign matter from the end of the axle hub before checking.



If the camber and caster are not as specified, adjust them.

If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, recheck the steering knuckle and front wheel for distortion and slack.


c.

Remove the camber-caster-kingpin gauge.

i.

Install the lock cap and a new cotter pin.


ii.

Install the front axle hub grease cap.


iii.

w/ Wheel Cap:

Install the wheel cap.



Hide 4.ADJUST CAMBER AND CASTER

NOTICE:

Inspect the toe-in after the camber and caster have been adjusted.


a.
C152364E02
1.76,0.052 3.073,0.552 1.313,0.5 12 true *b 0.052,0.042 1.49,0.552 1.438,0.51 12 true *a

Loosen the front and/or rear nut.

Text in Illustration
*a Front Side
*b Rear Side


b.

Turn the front camber adjust cam and adjust the camber.

Camber:

0°00' +/- 30' (0.0° +/- 0.5°)



c.

Turn the rear camber adjust cam and adjust the caster.

Camber:

4°30' +/- 30' (4.5° +/- 0.5°)


C152365E05
3.427,0.74 3.99,1.125 0.563,0.385 10 false *c 3.427,3.375 3.979,3.667 0.552,0.292 10 false *d 3.135,1.656 3.51,1.979 0.375,0.323 10 false (+) 2.604,1.646 2.927,1.917 0.323,0.271 10 false (-) 4.302,2.583 4.677,2.906 0.375,0.323 10 false (+) 3.771,2.594 4.094,2.865 0.323,0.271 10 false (-) 3.135,2.583 3.51,2.906 0.375,0.323 10 false (-) 2.604,2.594 2.927,2.865 0.323,0.271 10 false (+) 4.281,1.656 4.656,1.979 0.375,0.323 10 false (-) 3.781,1.656 4.104,1.927 0.323,0.271 10 false (+) 0.5,2.865 1.594,3.229 1.094,0.365 10 false (+): *e 0.5,3.188 1.635,3.521 1.135,0.333 10 false (-): *f 0.781,0.844 1.177,1.115 0.396,0.271 10 false *a 6.104,0.833 6.51,1.115 0.406,0.281 10 false *b

Text in Illustration
*a LH *b RH
*c Front Camber Adjust Cam *d Rear Camber Adjust Cam
*e Shorter *f Longer
V100135

Front of the Vehicle - -

NOTICE:
·

Perform the inspection while the vehicle is empty.

·

The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both the camber and caster.

·

Make sure to check the caster and toe-in after adjusting the camber.

·

Make sure to check the toe-in after adjusting the caster.

·

Try to adjust the camber and caster to the central values.



HINT:
·

The camber and caster changes by approximately +/- 10' when the front camber adjust cam is rotated by +/-1 gauge marks (+/- 1.0 mm).

·

The caster changes by approximately +/- 10' but the camber remains mostly unchanged when the rear camber adjust cam is rotated by +/-1 gauge marks (+/- 1.0 mm).




d.
C376373E01
0.813,0.396 1.125,0.594 0.313,0.198 10 false *a 0.813,0.771 1.125,0.969 0.313,0.198 10 false *b 1.75,0.396 2.063,0.594 0.313,0.198 10 false *c 1.75,0.781 2.063,0.979 0.313,0.198 10 false *d 1.135,1.365 1.448,1.563 0.313,0.198 10 false *e 2.49,3.688 2.885,3.938 0.396,0.25 10 false *f 0.104,0.052 0.51,0.344 0.406,0.292 10 false *g

How to read the adjustment chart (using examples).

Text in Illustration
*a Camber
*b Caster
*c Standard Value
*d Measured Value
*e Rear Cam Graduation
*f Front Cam Graduation
*g Example

i.

Find the wheel alignment standard value applicable for a particular model.


ii.

Mark the selected standard value on the adjustment chart.

Camber:

0°00' (0°)


Caster:

4°30' (4.50°)



iii.

Mark the alignment value measured on the adjustment chart when the vehicle was unloaded.

Example:
Camber:

-0°15' (-0.25°)

Caster:

4°00' (4.0°)



iv.

As shown in the chart, read the distance between the standard value and measured value, and then adjust the front and/or rear adjusting cam accordingly.

Front camber adjust cam:

+ (Shorter) 1.4


Rear camber adjust cam:

- (Longer) 1.5


C152367E03
6.333,3.5 6.802,3.781 0.469,0.281 10 false *d 3.49,1.063 3.958,1.365 0.469,0.302 10 false (+) 0.885,0.458 1.198,0.656 0.313,0.198 10 false *a 0.885,0.833 1.198,1.031 0.313,0.198 10 false *b 3.479,0.698 3.948,1 0.469,0.302 10 false *c 1.083,3.469 1.552,3.771 0.469,0.302 10 false (-) 5.927,3.479 6.396,3.781 0.469,0.302 10 false (+) 3.521,5.938 3.99,6.24 0.469,0.302 10 false (-)

Text in Illustration
*a Camber *b Caster
*c Rear Cam Graduation *d Front Cam Graduation



e.
C152364E02
1.76,0.052 3.073,0.552 1.313,0.5 12 true *b 0.052,0.042 1.49,0.552 1.438,0.51 12 true *a

Tighten the front and/or rear nut.

Text in Illustration
*a Front Side
*b Rear Side

Torque:

215 N*m (2192 kgf*cm, 159 ft.*lbf)



Hide 5.INSPECT TOE-IN

a.
C260042E08
0.521,0.094 0.979,0.427 0.458,0.333 10 false A 2.823,0.073 3.281,0.406 0.458,0.333 10 false B 1.698,1.833 1.948,2.094 0.25,0.26 10 false C 1.646,0.271 1.896,0.531 0.25,0.26 10 false D

Bounce the vehicle up and down at the corners to stabilize the suspension and inspect toe-in.

Toe-in (Unloaded Vehicle):
A + B:

0°12' +/-5' (0.20° +/-0.08°)

C - D:

2.5 +/- 1.0 mm (0.0984 +/- 0.0394 in.)


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 6.ADJUST TOE-IN

a.
C357298E01
2.521,1.26 2.823,1.479 0.302,0.219 10 true A

Loosen the 2 nuts.

NOTICE:

Nut A is a left-hand thread nut. Therefore, make sure to install in the correct direction.



b.

Adjust the toe-in by turning the left and right tie rod tubes equally.

Toe-in (Unloaded Vehicle):
A + B:

0°12' +/-5' (0.20° +/-0.08°)

C - D:

2.5 +/- 1.0 mm (0.0984 +/- 0.0394 in.)


NOTICE:

Nut A is a left-hand thread nut. Therefore, make sure to install in the correct direction.



c.
C357299

Measure the lengths of the right and left tie rod assembly.

Standard:
Right-left Difference:

2.0 mm (0.0787 in.) or less



d.

Secure the tie rod tube width-across-flats and temporarily install the nuts on both sides.


e.

Secure the tie rod tube width-across-flats and tighten the nuts on both sides.

Torque:

70 N*m (714 kgf*cm, 52 ft.*lbf)


NOTICE:
·

After adjusting the toe-in, check that the tolerance angle of the tie rod sub-assembly and No. 2 tie rod sub-assembly is 90°.

·

After adjusting the toe-in, check that permissible swinging angle of the ball joint on both ends of the tie rod assembly is at the center.




Hide 7.INSPECT WHEEL TURNING ANGLE

a.
C132439E21
0.523,0.183 0.717,0.363 0.194,0.18 10 *a 2.737,0.183 2.931,0.363 0.194,0.18 10 *a 0.865,0.183 1.059,0.363 0.194,0.18 10 *b 2.381,0.183 2.575,0.363 0.194,0.18 10 *b

Turn the steering wheel fully, and measure the wheel turning angle.

Wheel Turning Angle (Unloaded Vehicle):
Inside wheel Outside wheel
(Reference)
39°30' +1°00'/-2°00'
(39.50°+1.00°/-2.00°)
35°50'
(35.83°)


Text in Illustration
*a Inside
*b Outside
V100135

Front of the Vehicle


b.
C423429N01
1.49,3.583 1.802,3.781 0.313,0.198 10 false *a

If the right and left wheel turning angles differ from the specified range, adjust the wheel turning angle with the knuckle stopper bolts.

i.

Remove the knuckle stopper cover.


ii.

Secure the nut stopper bolt and loosen the lock nut.


iii.

Adjust the knuckle stopper bolt length.


iv.

Secure the nut stopper bolt and tighten the lock nut.

Torque:
Specified tightening torque : 49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Be sure to install the nut in the correct direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 255 mm (10.039 in.)): 30.9 N*m (315 kgf*cm, 23 ft.*lbf)




v.

Install a new knuckle stopper cover.



Hide 8.ADJUST CENTER ARM STOPPER

a.
C423433N01
0.802,0.698 1.354,0.698 false 1.01,1 1.563,1 false 0.583,1.573 1.135,1.573 false 2.51,0.365 2.823,0.563 0.313,0.198 10 false *a 2.042,0.448 2.354,0.646 0.313,0.198 10 false *b 0.552,0.615 0.865,0.813 0.313,0.198 10 false *c 0.792,0.906 1.104,1.104 0.313,0.198 10 false *e 0.365,1.479 0.677,1.677 0.313,0.198 10 false *d 1.594,2.365 1.906,2.563 0.313,0.198 10 false *f

Adjust so that the dimension between the center arm and center arm stopper bolt is as shown when the tire turning angle on the inner side is 39°30'.

Text in Illustration
*a 2.0 mm (0.079 in.) or more
*b 12.0 to 15.0 mm (0.473 to 0.590 in.)
*c Nut
*d Center Arm
*e Center Arm Stopper bolt
*f Torque Wrench Fulcrum Length


b.

While securing the center arm stopper bolt, tighten the nut.

Torque:
Specified tightening torque : 49 N*m (500 kgf*cm, 36 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 255 mm (10.039 in.)): 30.9 N*m (315 kgf*cm, 23 ft.*lbf)




Hide 9.ADJUST PITMAN ARM STOPPER

a.
C423434N01
2.24,1.073 2.792,1.073 true 2.708,0.813 1.646,0.813 1.646,0.813 2.042,1.177 true 0.583,1.573 1.135,1.573 false 2.729,1.875 3.042,2.073 0.313,0.198 10 false *a 2.49,1.448 2.802,1.646 0.313,0.198 10 false *b 2.865,0.99 3.177,1.188 0.313,0.198 10 false *c 2.76,0.698 3.073,0.896 0.313,0.198 10 false *e 0.365,1.479 0.677,1.677 0.313,0.198 10 false *d 1.594,2.365 1.906,2.563 0.313,0.198 10 false *f

Adjust so that the dimension between the pitman arm and pitman arm stopper bolt is as shown when the tire turning angle on the inner side is 39°30'.

Text in Illustration
*a 2.0 mm (0.079 in.) or more
*b 12.0 to 15.0 mm (0.473 to 0.590 in.)
*c Nut
*d Pitman Arm
*e Pitman Arm Stopper bolt
*f Torque Wrench Fulcrum Length


b.

While securing the pitman arm stopper bolt, tighten the nut.

Torque:
Specified tightening torque : 49 N*m (500 kgf*cm, 36 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 255 mm (10.039 in.)): 30.9 N*m (315 kgf*cm, 23 ft.*lbf)