Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P003A  Turbocharger/Supercharger Boost Control "A" Position Exceeded Learning Limit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P003A Turbocharger/Supercharger Boost Control "A" Position Exceeded Learning Limit Diagnosis Condition:
·

Ignition switch ON

·

The battery voltage is in the range of 10 to 16 V.

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

When the amount of operation after power has been turned ON is larger than HI range, or when the Hall IC output does not become constant after 5 seconds has elapsed


Malfunction Duration:

3 seconds or more


Turbocharger sub-assembly Class A DTC stored

MONITOR DESCRIPTION

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P003A Ignition switch ON for 3 seconds or more.


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P003A and other DTCs are output A
DTC P003A is output B




A

2.GO TO DTC CHART

B

3.CHECK DTC OUTPUT
2.GO TO DTC CHART

b.

Repair any malfunctioning parts indicated by related DTCs.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.

HINT:

Ignition switch ON to off verifies the wiping operation of the VNT actuator (DC motor).



e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read Current DTCs.

Result:
Result Proceed to
DTC P003A is output A
DTCs are not output B




A

5.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VN TURBO POSITION)
4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VN TURBO POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position / Actual VN Turbo Position


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE TURBOCHARGER SUB-ASSEMBLY
5.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END