Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P006E  Turbocharger/Supercharger Boost Control "A" Supply Voltage Circuit Low  P006F  Turbocharger/Supercharger Boost Control "A" Supply Voltage Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P006E Turbocharger/Supercharger Boost Control "A" Supply Voltage Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Power supply voltage is 8 V or less for at least 5 seconds.


Malfunction Duration:

3 seconds or more


·

Battery

·

Harness or connector


Class A DTC stored
P006F Turbocharger/Supercharger Boost Control "A" Supply Voltage Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Power supply voltage is 18 V or higher for at least 5 seconds.


Malfunction Duration:

3 seconds or more


·

Battery

·

Harness or connector


Class A DTC stored

MONITOR DESCRIPTION

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P006E
P006F
Ignition switch ON for 3 seconds or more.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P006E or P006F and other DTCs are output A
DTC P006E or P006F is output B


HINT:

If U010C is output, it may have been detected due to a CAN communication malfunction.




A

2.GO TO DTC CHART

B

3.CHECK DTC OUTPUT
2.GO TO DTC CHART

b.

Repair any malfunctioning parts indicated by related DTCs.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P006E or P006F is output A
DTCs are not output B




A

4.CHECK TURBOCHARGER SUB-ASSEMBLY

B

END

4.CHECK TURBOCHARGER SUB-ASSEMBLY
a.
A407240C07
0.375,0.99 0.781,1.271 0.406,0.281 0.958,1.802 1.438,1.25 true 2.125,1.813 1.708,1.25 true 0.531,1.073 0.844,1.271 0.313,0.198 10 false j5 0.865,1.854 1.385,2.063 0.521,0.208 10 false HLV 2.104,1.854 2.708,2.052 0.604,0.198 10 false HLG 0.125,0.156 0.438,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Turbocharger Sub-assembly)


Disconnect the turbocharger sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
j5-1 (HLV) - j5-2 (HLG) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT