Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0234  Turbocharger/Supercharger "A" Overboost Condition  P0299  Turbocharger/Supercharger "A" Underboost Condition  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0234 Turbocharger/Supercharger "A" Overboost Condition Diagnosis Condition:
·

Engine coolant temperature at engine start-up is 0°C (32°F) or more.

·

The condition that the intake air temperature at engine start-up is less than 0°C (32°F) remains for 500 seconds or more.

·

The condition that the intake air temperature at the engine start-up is higher than 0°C (32°F) remains in the range of 30 to 200 seconds.


·

The conditions described below remain for 9 seconds or more.

-

The target manifold pressure is 60 kPa (gauge) or more.

-

Engine speed is 1400 rpm or more and fuel injection rate is 60 mm3/st or more, or engine speed is 2000 rpm or more and fuel injection rate is 40 mm3/st or more, or engine speed is 2700 rpm or more and fuel injection rate is 20 mm3/st or more.

-

The variation of fuel injection rate is 8 mm3/st or less.

-

Atmospheric pressure is higher than 75 kPa.



Malfunction Status:

Deviation between the target manifold pressure and the actual manifold pressure: the condition that the deviation exceeds 20 to 40 kPa remains 6 seconds or more.


Malfunction Duration:

6 seconds or more


·

Turbocharger sub-assembly

·

EGR valve assembly

·

Manifold absolute pressure sensor

·

Vacuum hose


Class B1 DTC stored
P0299 Turbocharger/Supercharger "A" Underboost Condition Diagnosis Condition:

Engine coolant temperature at the engine start-up is 0°C (32°F) or above.


The conditions described below remain for 4 seconds or more.
·

The target manifold pressure is 100 kPa (gauge) or more.

·

Engine speed is 1200 rpm or more and fuel injection rate is 70 mm3/st or more, or engine speed is 2000 rpm or more and fuel injection rate is 40 mm3/st or more, or engine speed is 2700 rpm or more and fuel injection rate is 20 mm3/st or more.

·

The variation of fuel injection rate is 8 mm3/st or less.

·

Atmospheric pressure is higher than 75 kPa.

·

DPR auto-regeneration is not actuated.


Malfunction Status:

Deviation between the target manifold pressure and the actual manifold pressure: the condition that the deviation exceeds 20 to 50 kPa remains 6 seconds or more.


Malfunction Duration:

6 seconds or more


·

Abnormality in air intake system (disconnected air hose)

·

Turbocharger sub-assembly

·

EGR valve assembly

·

Manifold absolute pressure sensor

·

Mass air flow meter


Class B1 DTC stored

MONITOR DESCRIPTION

P0234:

The VNT actuator moves the nozzle vane steplessly by the LEA (Linear Electric Actuator) to control the turbo speed and boost pressure. It observes a deviation between the target boost pressure and actual boost pressure to check if the actual pressure is higher than the target pressure.

P0299:

The VNT moves the nozzle vane steplessly by the LEA (Linear Electric Actuator) to control the turbo speed and boost pressure. It compares the target boost pressure and actual boost pressure to check if the actual pressure is lower than the target pressure.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0234 Drive the vehicle that the target boost pressure is 60 kPa or more
P0299 Drive the vehicle that the target boost pressure is 100 kPa or more


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0234 or P0299 is output A
DTC P0234 or P0299 and other DTC are output B


HINT:

If P0045 is output, it may have been detected due to a turbocharger system malfunction.




A

2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

B

2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Make sure the manifold absolute pressure sensor hose is not clogged, ruptured, or cracked.


b.

Make sure the pipe on the intake manifold side is not clogged.


Result:
Proceed to
OK
NG



OK

3.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

9.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
3.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
A241069C44
0.49,1.104 0.906,1.396 0.417,0.292 1.875,1.344 2.24,1.708 true 1.406,1.354 1.156,1.74 true 2.292,1.75 2.677,1.979 0.385,0.229 10 false VC 0.26,0.115 0.531,0.313 0.271,0.198 10 false *a 1.021,1.76 1.198,1.906 0.177,0.146 10 false E 0.615,1.167 1.229,1.365 0.615,0.198 10 false B18
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


a.

Disconnect the manifold absolute pressure sensor.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B18-3 (VC) - B18-1 (E) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)

NG

CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (POWER SOURCE)

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position / Actual VN Turbo Position


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)

NG

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Valve Position / Data List / Actual EGR Valve Position and Target EGR Valve Position


d.

Check each step from 90 to 0% of the time lag of the target EGR valve opening and actual EGR valve opening.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 5 seconds.



Result:
Proceed to
OK
NG



OK

6.CHECK DTC OUTPUT

NG

7.REPLACE EGR VALVE ASSEMBLY
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE EGR VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
8.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
9.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Repair or replace the manifold absolute pressure sensor hose.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT