Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0107  Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Low  P0108  Manifold Absolute Pressure / Barometric Pressure Sensor Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0107 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Output of the sensor remains at 0.19 V or less for 3 seconds or longer.


Malfunction Duration:
3 seconds or more
·

Harness or connector

·

Manifold absolute pressure sensor

·

ECM


Class A DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

Output of the sensor remains greater than 4.49 V for 3 seconds or longer.


Malfunction Duration:
3 seconds or more
·

Harness or connector

·

Manifold absolute pressure sensor

·

ECM


Class A DTC stored

MONITOR DESCRIPTION

The manifold absolute pressure sensor installed at the outlet of the diesel throttle consistently detects boost pressure.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0107
P0108
Ignition switch ON for 3 seconds or more.


WIRING DIAGRAM

A407156E12
2.115,1.094 2.427,1.292 0.313,0.198 10 false VC 2.063,1.448 2.375,1.646 0.313,0.198 10 false PIM 2.208,1.844 2.521,2.042 0.313,0.198 10 false E 2.458,0.969 2.771,1.167 0.313,0.198 10 false 3 2.458,1.354 2.771,1.552 0.313,0.198 10 false 2 2.458,1.708 2.771,1.906 0.313,0.198 10 false 1 0.844,2.24 1.156,2.438 0.313,0.198 10 false B18 0.813,2.448 3.385,2.844 2.573,0.396 10 false Manifold Absolute Pressure Sensor 4.594,1.104 4.969,1.313 0.375,0.208 10 false M-51 4.594,1.469 4.969,1.677 0.375,0.208 10 false E-67 4.594,1.854 4.969,2.063 0.375,0.208 10 false E-77 4.969,1.104 5.344,1.313 0.375,0.208 10 false B142 4.969,1.479 5.344,1.688 0.375,0.208 10 false B142 4.969,1.844 5.344,2.052 0.375,0.208 10 false B142 5.031,0.896 5.344,1.094 0.313,0.198 10 false 68 5.063,1.313 5.375,1.51 0.313,0.198 10 false 5 5.042,1.677 5.354,1.875 0.313,0.198 10 false 90 5.365,1.104 5.677,1.302 0.313,0.198 10 false VC 5.354,1.479 5.667,1.677 0.313,0.198 10 false PIM 5.354,1.844 5.667,2.042 0.313,0.198 10 false E4 5.802,2.688 6.469,2.99 0.667,0.302 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Check the connector connection for the manifold absolute pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

12.CONNECT SECURELY
2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Check the installation of the manifold absolute pressure sensor .


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the manifold absolute pressure sensor.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

NG

11.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
3.CHECK HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-51 - Body ground and other terminals Always 10 kΩ or higher
E-67 - Body ground and other terminals Always 10 kΩ or higher
E-54 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-51 - E-67 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-51 - B18-3 (VC) Always Below 1 Ω
E-67 - B18-2 (PIM) Always Below 1 Ω
E-77 - B18-1 (E) Always Below 1 Ω



Result:
Proceed to
OK
NG


A241069C41
0.427,1.125 0.854,1.385 0.427,0.26 0.958,1.76 1.375,1.344 true 1.635,1.844 1.656,1.344 true 2.229,1.74 1.854,1.344 true 0.531,1.177 0.99,1.375 0.458,0.198 10 false B18 0.25,0.188 0.708,0.385 0.458,0.198 10 false *a 0.854,1.781 1.313,1.979 0.458,0.198 10 false E 1.5,1.917 1.958,2.115 0.458,0.198 10 false PIM 2.271,1.76 2.729,1.958 0.458,0.198 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)



OK

6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
A241069C35
0.469,1.135 0.885,1.427 0.417,0.292 1.875,1.344 2.24,1.708 true 1.406,1.354 1.156,1.74 true 2.292,1.75 2.677,1.979 0.385,0.229 10 false VC 0.26,0.115 0.531,0.313 0.271,0.198 10 false *a 1.021,1.76 1.198,1.906 0.177,0.146 10 false E 0.573,1.198 1.188,1.396 0.615,0.198 10 false B18
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


a.

Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B18-3 (VC) - B18-1 (E) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

8.REPLACE ECM
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0107 or P0108 is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
11.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Repair or replace the manifold absolute pressure sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the manifold absolute pressure sensor.



Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
12.CONNECT SECURELY
a.

Connect securely the manifold absolute pressure sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT
13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END