Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P104E  Turbocharger/Supercharger Boost Control "A" Module EEPROM Error  P104F  Turbocharger/Supercharger Boost Control "A" Module Processor  


DESCRIPTION

Refer to DTC P0045 (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>P0045).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P104E Turbocharger/Supercharger Boost Control "A" Module EEPROM Error Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Data recorded in 3 sectors of EEPROM does not match.


Malfunction Duration:

3 seconds or more.


Turbocharger sub-assembly Class A DTC stored
P104F Turbocharger/Supercharger Boost Control "A" Module Processor Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:
·

Difference between ROM read data and previous data.

·

Difference between RAM write data and read data.


Malfunction Duration:

3 seconds or more.


Turbocharger sub-assembly Class A DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P104E
P104F
Idle for 5 seconds or more after engine warm-up

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P104E or P104F and other DTC are output A
DTC P104E or P104F is output B


HINT:

If U010C is output, it may have been detected due to a CAN communication malfunction.




A

2.GO TO DTC CHART

B

3.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
2.GO TO DTC CHART

NEXT

3.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
3.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.

HINT:

Ignition switch ON to off verifies the wiping operation of the VNT actuator (DC motor).



e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Result:
Result Proceed to
DTC P104E or P104F is output A
DTCs are not output B




A

4.CHECK CONNECTOR CONNECTION CONDITION (TURBOCHARGER SUB-ASSEMBLY)

B

7.CHECK DTC OUTPUT
4.CHECK CONNECTOR CONNECTION CONDITION (TURBOCHARGER SUB-ASSEMBLY)
a.

Check the connector connection for the turbocharger sub-assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

9.CONNECT SECURELY
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P104E or P104F is output A
DTCs are not output B




A

6.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)

B

END

6.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.

HINT:

Ignition switch ON to off verifies the wiping operation of the VNT actuator (DC motor).



e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Result:
Result Proceed to
DTC P104E or P104F is not output A
DTC P104E or P104F is output B




A

7.CHECK DTC OUTPUT

B

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
9.CONNECT SECURELY
a.

Connect securely the turbocharger sub-assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT