Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2202  NOx Sensor Circuit Low Bank 1 Sensor 1  P2203  NOx Sensor Circuit High Bank 1 Sensor 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2202 NOx Sensor Circuit Low Bank 1 Sensor 1 Diagnosis Condition:
·

Ignition switch ON

·

Exhaust brake does not operate

·

DPR not regenerating

·

No malfunction in CAN communication system

·

Estimated concentration of NOx emitted from the engine is at the value determined by the ECM or lower

·

Engine speed 450 rpm or higher and below 2900 rpm


Malfunction Status:

Short in No. 1 nitrogen oxides sensor internal circuit received continuously from CAN data for 60 seconds or more


Malfunction Duration:

60 seconds or more


·

No. 1 nitrogen oxides sensor


Class A DTC stored
P2203 NOx Sensor Circuit High Bank 1 Sensor 1 Diagnosis Condition:
·

Ignition switch ON

·

Exhaust brake does not operate

·

DPR not regenerating

·

No malfunction in CAN communication system

·

Estimated concentration of NOx emitted from the engine is at the value determined by the ECM or lower

·

Engine speed 450 rpm or higher and below 2900 rpm


Malfunction Status:

Open in No. 1 nitrogen oxides sensor internal circuit received continuously from CAN data for 60 seconds or more.


Malfunction Duration:

60 seconds or more


·

No. 1 nitrogen oxides sensor


Class A DTC stored

MONITOR DESCRIPTION

·

No. 1 nitrogen oxides sensor is controlled by the nitrogen oxides sensor controller.

·

The nitrogen oxides sensor controller is connected to the ECM and DCU (emission control ECU) via CAN communication, and sends/receives information.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2202
P2203
60 seconds or more with the engine speed at 450 rpm or higher

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2202 or P2203 is output A
DTC P2202, P2203 and other DTCs are output B


HINT:

If U029D is output, it may have been detected due to a CAN communication malfunction.




A

2.REPLACE NO. 1 NITROGEN OXIDES SENSOR

B

2.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END