Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P22D3  Turbocharger Turbine Inlet Valve Stuck Closed  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P22D3 Turbocharger Turbine Inlet Valve Stuck Closed Diagnosis Condition:
·

Ignition switch ON

·

The battery voltage is in the range of 10 to 16 V.

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

When motor drive load is 95% or more for 3 seconds continuously and restoration operation fails 5 times.


Malfunction Duration:

3 seconds or more


Turbocharger sub-assembly Class A DTC stored

MONITOR DESCRIPTION

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P22D3
·

Idle the engine for 5 seconds after warming up the engine.

·

Ignition switch ON to OFF (wiping operation)



CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P22D3 and other DTCs are output A
DTC P22D3 is output B


HINT:

If U010C is output, it may have been detected due to a CAN communication malfunction.




A

2.GO TO DTC CHART

B

3.CHECK DTC OUTPUT
2.GO TO DTC CHART

NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P22D3 is not output A
DTC P22D3 is output B




A

END

B

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)
4.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position / Actual VN Turbo Position.


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.


Result:
Proceed to
OK
NG




OK

END

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY