Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P259E  Turbocharger "A" Boost Control Position at Low Limit  P259F  Turbocharger "A" Boost Control Position at High Limit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P259E Turbocharger "A" Boost Control Position at Low Limit Diagnosis Condition:
·

Ignition switch off

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

When a wiping operating range narrower than Lo range is detected 2 times.


Malfunction Duration:

3 seconds or more


Turbocharger sub-assembly Class A DTC stored
P259F Turbocharger "A" Boost Control Position at High Limit Diagnosis Condition:
·

Ignition switch off

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

When a wiping operating range wider than HI range is detected 2 times.


Malfunction Duration:

3 seconds or more


Turbocharger sub-assembly Class A DTC stored

MONITOR DESCRIPTION

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P259E
P259F
·

Start the engine and idle the engine for 5 seconds or more.

·

Ignition switch ON to OFF (wiping operation)



CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P259E or P259F and other DTC are output A
DTC P259E or P259F is output B


HINT:

If U010C is output, it may have been detected due to a CAN communication malfunction.




A

2.GO TO DTC CHART

B

3.CHECK DTC OUTPUT
2.GO TO DTC CHART

NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P259E or P259F are output B




A

END

B

4.CHECK TURBOCHARGER SUB-ASSEMBLY
4.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check the turbocharger external appearance and make sure no foreign substances are trapped around the link.

A385726

Result:
Result Proceed to
Foreign substances stuck around the variable nozzle operation link
(remove the foreign substance and proceed to the next inspection)
A
No foreign substances stuck around the variable nozzle operation link B




A

5.REMOVE THE FOREIGN SUBSTANCES

B

6.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
5.REMOVE THE FOREIGN SUBSTANCES
a.

Remove the foreign substances


Result:
Proceed to
NEXT



NEXT

6.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
6.INSPECT TURBOCHARGER SUB-ASSEMBLY (WIPING OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.

HINT:

Ignition switch ON to off verifies the wiping operation of the VNT actuator (DC motor).



e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P259E or P259F is not output* A
DTC P259E or P259F are output B


*: P259E or P259F is detected due to foreign substances jammed in the variable nozzle operation link.



A

7.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)

B

REPLACE TURBOCHARGER SUB-ASSEMBLY

7.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position / Actual VN Turbo Position.


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY