Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P24AE  Particulate Matter Sensor Circuit  P24AF  Particulate Matter Sensor Circuit Range/Performance  P24B0  Particulate Matter Sensor Circuit Low  P24B1  Particulate Matter Sensor Circuit High  P24B3  Particulate Matter Sensor Heater Control Circuit/Open  P24B4  Particulate Matter Sensor Heater Control Circuit Range/Performance  P24B5  Particulate Matter Sensor Heater Control Circuit Low  P24B6  Particulate Matter Sensor Heater Control Circuit High  P24B7  Particulate Matter Sensor Heater Resistance  P24D1  Particulate Matter Sensor Regeneration Incomplete  P24DA  Particulate Matter Sensor Exhaust Sample Error Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P24AE Particulate Matter Sensor Circuit Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


Particulate matter sensor Class C DTC stored
P24AF Particulate Matter Sensor Circuit Range/Performance Diagnosis Condition:
·

PM sensor regeneration is in progress.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


·

Particulate matter sensor

·

Monolithic converter assembly


Class C DTC stored
P24B0 Particulate Matter Sensor Circuit Low Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


Particulate matter sensor Class C DTC stored
P24B1 Particulate Matter Sensor Circuit High Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


Particulate matter sensor Class C DTC stored
P24B3 Particulate Matter Sensor Heater Control Circuit/Open Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


·

Particulate matter sensor

·

Battery


Class C DTC stored
P24B4 Particulate Matter Sensor Heater Control Circuit Range/Performance Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


Particulate matter sensor Class C DTC stored
P24B5 Particulate Matter Sensor Heater Control Circuit Low Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


·

Particulate matter sensor

·

Battery


Class C DTC stored
P24B6 Particulate Matter Sensor Heater Control Circuit High Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


·

Particulate matter sensor

·

Battery


Class C DTC stored
P24B7 Particulate Matter Sensor Heater Resistance Diagnosis Condition:
·

PM sensor regeneration is in progress.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


·

Particulate matter sensor

·

Battery


Class C DTC stored
P24D1 Particulate Matter Sensor Regeneration Incomplete Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


·

Particulate matter sensor

·

Monolithic converter assembly


Class C DTC stored
P24DA Particulate Matter Sensor Exhaust Sample Error Bank 1 Diagnosis Condition:
·

The PM sensor is in operation.

·

Battery voltage is in the range of 10 V to 16 V

·

The ignition switch ON for 5 seconds or more (the starter is not actuated).


Malfunction Status:

PM sensor malfunction for 3 seconds or more. (2 trip detection logic)


Malfunction Duration:

3 seconds or more


·

Particulate matter sensor

·

Monolithic converter assembly


Class C DTC stored

MONITOR DESCRIPTION

P24AE
·

Abnormality in the particulate matter sensor controller is detected by the self-diagnosis function of the particulate matter sensor.


P24AF
·

The particulate matter sensor is installed downstream of the monolithic converter assembly to monitor the PM volume from the monolithic converter assembly.


P24B0
·

Short circuit in the particulate matter sensor controller is detected by the self-diagnosis function of the particulate matter sensor.


P24B1
·

Disconnection in the particulate matter sensor controller is detected by the self-diagnosis function of the particulate matter sensor.


P24B3
·

Abnormality in the particulate matter sensor power supply voltage is detected by the self-diagnosis function of the particulate matter sensor.


P24B4
·

Abnormality in the particulate matter sensor heater is detected by the self-diagnosis function of the particulate matter sensor.


P24B5
·

Abnormality in the particulate matter sensor power supply voltage is detected by the self-diagnosis function of the particulate matter sensor.


P24B6
·

Abnormality in the particulate matter sensor power supply voltage is detected by the self-diagnosis function of the particulate matter sensor.


P24B7
·

The particulate matter sensor is installed downstream of the monolithic converter assembly to monitor the PM volume from the monolithic converter assembly.


P24D1
·

Abnormality in the particulate matter sensor regeneration is detected by the self-diagnosis function of the particulate matter sensor.


P24DA
·

Clogging in the particulate matter sensor head is detected by the self-diagnosis function of the particulate matter sensor.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P24AE
P24AF
P24B0
P24B1
P24B3
P24B4
P24B5
P24B6
P24B7
P24D1
P24DA
PM forced regeneration

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read Current DTCs.

Result:
Result Proceed to
DTC P24AE, P24B4 or P24B6 is output A
DTC P24AF, P24B1, P24B4 or P24B7 is output B
DTC P24AE, P24AF, P24B0, P24B1, P24B3, P24B4, P24B5, P24B6, P24B7, P24D1 or P24DA and other DTC are output C




A

2.CHECK HARNESS AND CONNECTOR (PARTICULATE MATTER SENSOR VOLTAGE)

B

6.REPLACE PARTICULATE MATTER SENSOR

C

2.CHECK HARNESS AND CONNECTOR (PARTICULATE MATTER SENSOR VOLTAGE)
a.

Disconnect the particulate matter sensor connector.


A451444C01
0.219,0.938 0.635,1.219 0.417,0.281 1.313,1.823 1.625,1.354 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.302,0.99 0.76,1.188 0.458,0.198 10 false P15 1.031,1.854 1.49,2.052 0.458,0.198 10 false CANH
*a Front view of wire harness connector
(to Particulate Matter Sensor)


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive terminal - Battery negative terminal Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P15-3 (CANH) - Body ground Always Below 2 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE PARTICULATE MATTER SENSOR

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE PARTICULATE MATTER SENSOR
a.

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
6.REPLACE PARTICULATE MATTER SENSOR
a.

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT