Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM D

N04C-WA ENGINE CONTROL  ECD SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


A093827


When troubleshooting Euro-OBD vehicles, the vehicle must be connected to the GTS. Various data output from the vehicle's Engine Control Module (ECM) can then be read.

The Malfunction Indicator Lamp (MIL) is illuminated when the vehicle's on-board computer detects a malfunction in the computer itself or in drive system components. In addition, the applicable Diagnostic Trouble Codes (DTCs) are recorded in the ECM memory.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

If the malfunction does not recur, the MIL stays ON until the ignition switch is turned off, and then the MIL turns off when the ignition switch is turned ON. Be aware that the DTCs remain recorded in the ECM memory.

To check the DTCs, connect the GTS to the DLC3 on the vehicle.

FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


INSPECT BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


MIL ILLUMINATION PATTERN


a.

MIL (Malfunction Indicator Lamp) displays according to the vehicle condition.

HINT:

MIL display depends on malfunction class of each DTC.


Malfunction Class Requirement
Class A Malfunction where exhaust gas components exceed the OBD threshold
Class B1 Malfunction where exhaust gas components may exceed the OBD threshold
Class B2 Malfunction where it is predicted that exhaust gas components will not reach a level that exceeds the OBD threshold
Class C Malfunction where it is predicted that exhaust gas components will not reach a level that exceeds the regulation value

A446861E02
2.094,3.042 3.042,3.385 3.042,3.385 3,3.042 false 2.479,3.031 3.021,3.365 false 1.448,3.01 1.49,3.333 false 0.771,2.99 0.542,3.365 false 0.365,0.625 1.135,0.823 0.771,0.198 10 false IG ON 4.24,0.594 5.615,0.792 1.375,0.198 10 false Engine ON 0.354,1.24 1.198,1.625 0.844,0.385 10 false (1): Bulb test 1.427,1.208 4.635,1.406 3.208,0.198 10 false (2): Readiness status 3.198,1.208 4.125,1.844 0.927,0.635 10 false (3): MIL status (Engine OFF) 5.604,1.177 6.563,1.813 0.958,0.635 10 false (4): MIL status (Engine ON) 0.115,0.063 2.177,0.5 2.063,0.438 10 false MIL Illumination Pattern: 0.156,2.042 0.396,2.594 0.24,0.552 10 false MIL ON 0.156,2.729 0.479,3.073 0.323,0.344 10 false MIL OFF 6.292,2.885 7.063,3.531 0.771,0.646 10 false Time [sec.] 4.219,3.385 6.625,3.74 2.406,0.354 10 false Example: In case of "No malfunction" 2.844,3.385 3.781,3.604 0.938,0.219 10 false 5 seconds 1.208,3.365 2.146,3.583 0.938,0.219 10 false 10 seconds 0.25,3.365 1.188,3.583 0.938,0.219 10 false 5 seconds


b.

Refer to below for the relation between MIL display of (1) to (4) and its description.

(1): Bulb test

Bulb operational: MIL ON

Bulb non operational: MIL OFF

HINT:

If the MIL is not illuminated, check the MIL circuit.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>MIL Circuit



(2): Readiness status

A446862E02
1.979,0.823 3.354,1.021 1.375,0.198 10 false Readiness 5.375,0.823 6.51,1.167 1.135,0.344 10 false Readiness status 0.208,1.896 1.479,2.635 1.271,0.74 10 false Readiness "Ready" 1.854,1.844 4.677,2.479 2.823,0.635 10 false In case of the readiness for all monitored components is complete. 5.729,1.198 6.365,1.604 0.635,0.406 10 false Ready 5.656,3.302 6.531,3.698 0.875,0.396 10 false Not ready 5.667,2.771 6.5,3.219 0.833,0.448 10 false 5 seconds 5.646,4.854 6.479,5.302 0.833,0.448 10 false 5 seconds 0.354,3.896 1.333,4.604 0.979,0.708 10 false Readiness "Not Ready" 1.802,3.781 4.625,4.417 2.823,0.635 10 false In case of the readiness for one or more of the monitored components is not complete.

HINT:

There are some items that cannot be determined if the vehicle is not driven during troubleshooting. Therefore, when the ignition switch is normally turned to ON, the MIL blinks 5 times to indicate Readiness "Not Ready".

(Even though it indicates "Not Ready", this is not a malfunction.)


(3): MIL status (Engine OFF)

HINT:
·

This sequence is repeated until the engine starts or the ignition switch is turned off.

·

For "Class B1", the MIL status changes from Mode 3 to Mode 4 (continuous illumination) if the cumulative elapsed time exceeds 200 hours after it is detected.



A446863E04
0.635,1.083 1.708,1.281 1.073,0.198 10 false Class A 0.25,1.438 1.74,1.844 1.49,0.406 10 false Class B1 (200 hours or more) 0.375,2.604 1.667,3.156 1.292,0.552 10 false Class B1 (Less than 200 hours) 0.563,3.281 2.021,3.594 1.458,0.313 10 false Class B2 0.615,4.885 2.073,5.198 1.458,0.313 10 false Class C 0.656,0.292 1.427,0.49 0.771,0.198 10 false Class 3.76,0.271 5.292,0.469 1.531,0.198 10 false MIL status 2.021,0.948 2.938,1.146 0.917,0.198 10 false MIL ON 2.01,1.927 2.927,2.125 0.917,0.198 10 false MIL OFF 2,2.594 2.917,2.792 0.917,0.198 10 false MIL ON 2.052,4.385 2.969,4.583 0.917,0.198 10 false MIL ON 2.031,6.115 2.948,6.313 0.917,0.198 10 false MIL ON 1.99,3.479 2.906,3.677 0.917,0.198 10 false MIL OFF 2.031,5.333 2.948,5.531 0.917,0.198 10 false MIL OFF 2.01,7.042 2.927,7.24 0.917,0.198 10 false MIL OFF 3.021,3.792 4.396,3.99 1.375,0.198 10 false 5 seconds 3.771,3.792 5.146,3.99 1.375,0.198 10 false 5 seconds 3.594,5.604 4.969,5.802 1.375,0.198 10 false 5 seconds 3.396,7.292 4.771,7.49 1.375,0.198 10 false 5 seconds 2.833,5.594 4.208,5.792 1.375,0.198 10 false 3 seconds 2.656,7.292 4.031,7.49 1.375,0.198 10 false 1 second 0.5,6.521 1.625,7.125 1.125,0.604 10 false No malfunction 1.927,0.635 2.844,0.833 0.917,0.198 10 false Mode 4 1.896,2.375 2.813,2.573 0.917,0.198 10 false Mode 3 1.875,5.844 2.792,6.042 0.917,0.198 10 false Mode 1 1.865,4.104 2.781,4.302 0.917,0.198 10 false Mode 2

(4): MIL status (Engine ON)

HINT:

For "Class B1", the MIL status changes from Mode 3 to Mode 4 (continuous illumination) if the cumulative elapsed time exceeds 200 hours after it is detected.


A446864E04
0.813,1.167 1.885,1.365 1.073,0.198 10 false Class A 0.396,1.469 1.875,1.938 1.479,0.469 10 false Class B1 (200 hours or more) 0.448,2.604 1.76,3.208 1.313,0.604 10 false Class B1 (Less than 200 hours) 0.573,3.365 2.031,3.677 1.458,0.313 10 false Class B2 0.615,4.885 2.073,5.198 1.458,0.313 10 false Class C 3.583,0.219 5.115,0.417 1.531,0.198 10 false MIL status 0.792,0.219 2.323,0.417 1.531,0.198 10 false Class 2.781,0.625 4.313,0.823 1.531,0.198 10 false Engine ON 2.99,3.51 4.521,3.708 1.531,0.198 10 false 15 seconds 0.573,6.563 2.104,6.76 1.531,0.198 10 false No malfunction 2.021,1.99 3.552,2.188 1.531,0.198 10 false MIL OFF 2.042,1.135 3.573,1.333 1.531,0.198 10 false MIL ON 2.063,2.583 3.594,2.781 1.531,0.198 10 false MIL ON 2.01,4.427 3.542,4.625 1.531,0.198 10 false MIL ON 2.031,6.219 3.563,6.417 1.531,0.198 10 false MIL ON 2.042,3.365 3.573,3.563 1.531,0.198 10 false MIL OFF 2.031,7.083 3.563,7.281 1.531,0.198 10 false MIL OFF 1.958,0.583 2.875,0.781 0.917,0.198 10 false Mode 4 1.958,2.333 2.875,2.531 0.917,0.198 10 false Mode 3 1.969,4.104 2.885,4.302 0.917,0.198 10 false Mode 2 1.979,5.865 2.896,6.063 0.917,0.198 10 false Mode 1