Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM J

N04C-WA ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM. By turning the ignition switch to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should illuminate and should then turn off. If the MIL remains illuminated or does not illuminate, conduct the following troubleshooting procedure. If the ECM detects any trouble, the MIL illuminates. At this time, the ECM records a DTC in the memory.

WIRING DIAGRAM

A407168E08
1.115,1.917 2.365,2.094 1.25,0.177 10 false Combination Meter 2.271,1.01 2.552,1.198 0.281,0.188 10 false 24 1.125,1.74 1.406,1.927 0.281,0.188 10 false J1 1.885,1.115 2.219,1.313 0.333,0.198 10 false CHK 5.688,1.958 6.073,2.156 0.385,0.198 10 false ECM 5.25,1.125 5.469,1.313 0.219,0.188 10 false W 4.792,1.125 5.208,1.333 0.417,0.208 10 false A115 4.865,0.917 5.031,1.115 0.167,0.198 10 false 63 4.396,1.125 4.813,1.333 0.417,0.208 10 false V-9

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK THAT MIL ILLUMINATES
a.

Turn the ignition switch to ON.


b.

Check the illumination of the MIL.

HINT:

Refer to "MIL ILLUMINATION PATTERN" in the "DIAGNOSIS SYSTEM" section.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSIS SYSTEM



Result:
Result Proceed to
MIL status of MIL illumination pattern is mode 1 (no malfunction) A
MIL status of MIL illumination pattern is modes 2 to 4 (DTC of malfunction classes A to C is detected) B
MIL remains on (always illuminated) C
MIL remains off (Does not illuminate at all) D



A

SYSTEM NORMAL

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

C

2.CHECK DTC OUTPUT

D

6.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)
2.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

According to the display on the GTS, select "Health Check".


e.

Check if any DTCs have been stored. Note any DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.
A241244C10
1.5,0.333 1.833,0.583 0.333,0.25 1.219,1.927 0.938,1.365 true 0.094,0.083 0.333,0.271 0.24,0.188 10 false *a 1.188,1.948 1.802,2.146 0.615,0.198 10 false CHK 1.583,0.385 1.813,0.552 0.229,0.167 10 false J1
*a Front view of wire harness connector
(to Combination Meter Assembly)


A405886C03
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Disconnect the combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-24 (CHK) - V-9 Always Below 1 Ω
J1-24 (CHK) or V-9 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK THAT MIL ILLUMINATES
5.CHECK THAT MIL ILLUMINATES
a.

Turn the ignition switch to ON.


b.

Check the illumination of the MIL.

HINT:

Refer to "MIL ILLUMINATION PATTERN" in the "DIAGNOSIS SYSTEM" section.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSIS SYSTEM



Result:
Result Proceed to
MIL remains on (always illuminated) A
MIL status of MIL illumination pattern is mode 1 (no malfunction) B



A

REPLACE COMBINATION METER ASSEMBLY

B

END

6.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.


d.

Check the status of the MIL while performing the Active Test.


Result:
Result Proceed to
Changes A
Does not change B



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

REPLACE COMBINATION METER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.
A241244C11
1.5,0.333 1.833,0.583 0.333,0.25 1.219,1.927 0.938,1.365 true 0.094,0.083 0.333,0.271 0.24,0.188 10 false *a 1.188,1.948 1.802,2.146 0.615,0.198 10 false CHK 1.583,0.385 1.813,0.552 0.229,0.167 10 false J1
*a Front view of wire harness connector
(to Combination Meter Assembly)


A405886C03
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Disconnect the combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-24 (CHK) - V-9 Always Below 1 Ω
J1-24 (CHK) or V-9 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)