1.VISUALLY CHECK HOSES, CONNECTIONS AND GASKETS
Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.
Detachment or other problems with the engine oil dipstick, filler cap, PCV hose and other components may cause the engine to run improperly.
Air suction caused by disconnections, looseness or cracks in the parts of the air induction system between the throttle body and cylinder head will cause engine failure or engine malfunction.
If any defects are found, replace parts as necessary.
2.INSPECT FOR EGR VALVE ASSEMBLY
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Read the Data List "Target EGR Position" and "Actual EGR Valve Pos." values during the Active Test.
The Actual EGR Valve Pos. value follows the Target EGR Position value.
If the result is not as specified, refer to DTC P1458.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>P1458
3. DPR MANUAL FORCED REGENERATION
Park the vehicle in a safe location.
Make sure there are no flammable materials near the vehicle and its exhaust pipes, as the DPR catalyst becomes hot during DPR forced regeneration.
Change the shift position to N and securely pull the parking brake.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and using the GTS, read the DTCs.
Check that no DTCs are output.
If DTCs are output, perform repairs according to the procedure for the output DTCs.
Start the engine and warm it up until the engine coolant temperature stabilizes.
(The engine coolant temperature is 40°C (104°F) or higher)
Enter the following menus: Powertrain / Engine / Utility / DPR Check.
Select "Check Start" and check according to the GTS display.
Select "Catalyst Regeneration" and perform manual forced regeneration according to the GTS display.
Check that the engine speed decreases, the exhaust brake is released (indicator in meter turns off) and forced regeneration completes.
To cancel regeneration before it completes, press the "DPR switch assembly" again or lightly depress the accelerator pedal.
When canceling regeneration before it completes or performing regeneration again , set the idle volume to "MAX" and leave the vehicle for 20 minutes.
Make sure to perform this procedure, as it releases unburned hydrocarbons that accumulate in the EGR system to prevent blockages in the EGR system, etc.
If the exhaust brake repeatedly opens and closes (or does not close) during forced regeneration, check the exhaust system. Also, check the engine load (friction of the generator, cooler compressor, etc.), as it may be extremely high.
If regeneration takes a long time to complete (60 minutes or more) or P2458 (Particulate Filter Regeneration Duration Bank 1) is output, repair the malfunction location and perform manual forced regeneration again.
After manual forced regeneration is started, it will take approximately 15 to 25 minutes to complete.
After DPR manual forced regeneration completes, select "DPR Differential Pressure Check" and perform the DPR differential pressure check according to the GTS display.
Perform the DPR differential pressure check after manual regeneration. However, when the exhaust temperature is high, accurate measurements cannot be obtained, so perform it when the DPR inlet side exhaust temperature is approximately C200°C (392°F) or less.
After the engine speed is increased and the DPR differential pressure is displayed, record the value and stop the DPR differential pressure check according to the instructions on the GTS.
15 kPa or less
If the differential pressure does not fluctuate, perform the following check.
Check for open holes or cracks in the differential pressure hose.
(If the hose is 3 or more years old, replace it.)
Check that the hose clamp is not detached or loose.
Check that the differential pressure pipe is not blocked.
(Apply compressed air to the DPR unit side of the differential pressure pipe and check that air passes through.)
Perform an electrical check of the differential pressure sensor, and if there are any malfunctions, replace it.
If the DPR differential pressure exceeds the standard value.
Clean or replace the monolithic converter assembly.
Check the engine oil level.
Click hereEngine / Hybrid System>N04C-WA (LUBRICATION)>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION