Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P1458  EGR Actuator Major Malfunction  P1459  EGR Actuator Minor Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1458 EGR Actuator Major Malfunction Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

There is no disconnection in harness connected to EGR control.

·

Ignition switch ON. (Not related to engine speed)


Malfunction Status:
·

When actual opening of the EGR valve is not followed up to commanded opening from the ECM.

·

When the ECM commands the EGR valve to operate out of range.

·

Abnormality of power supply voltage.

·

When the EGR valve is sticking.


Malfunction Duration:

3 seconds or more


·

EGR valve sealing face

·

EGR valve assembly

·

Harness or connector

·

ECM


Class A DTC stored
P1459 EGR Actuator Minor Malfunction Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

The engine stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.

·

Ignition switch ON.


Malfunction Status:
·

The motor in the actuator malfunction occurs.

·

The temperature sensor in the actuator malfunction occurs.

·

Initialization operation cannot be completed at the time of initialization check (performed at the time ignition switch ON).


Malfunction Duration:

3 seconds or more


·

EGR valve sealing face

·

EGR valve assembly

·

Harness or connector

·

ECM


Class A DTC stored

MONITOR DESCRIPTION

·

EGR valve is a poppet type.

·

EGR valve opening is controlled by engine speed and amount of intake air.

·

EGR valve opening is adjusted by ECM and CAN communication.

·

EGR valve wipes off soot from its surface when the ignition switch is off.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1458
P1459
Idle the engine for 1 second or more after warming up the engine.

WIRING DIAGRAM

A451038E04
2.375,2.781 3.458,3.063 1.083,0.281 10 false EFI NO. 1 1.333,2.792 2.417,3.073 1.083,0.281 10 false EFI-MAIN 0.604,4.271 1.688,4.552 1.083,0.281 10 false Battery 3.073,3 4.156,3.281 1.083,0.281 10 false ACT PWR 5.844,4.313 6.927,4.594 1.083,0.281 10 false ECM 3.042,0.406 4.125,0.688 1.083,0.281 10 false CANH 3.052,0.958 4.135,1.24 1.083,0.281 10 false CANL 3.594,0.24 4.677,0.521 1.083,0.281 10 false 5 3.594,0.75 4.677,1.031 1.083,0.281 10 false 2 2.125,0.24 3.208,0.521 1.083,0.281 10 false 4 2.115,0.74 3.198,1.021 1.083,0.281 10 false 1 2.354,0.365 3.438,0.646 1.083,0.281 10 false +B 2.375,0.927 3.458,1.208 1.083,0.281 10 false E 4.646,0.417 5.729,0.698 1.083,0.281 10 false E-59 4.646,0.938 5.729,1.219 1.083,0.281 10 false E-79 5.01,0.406 6.094,0.688 1.083,0.281 10 false B142 5.01,0.948 6.094,1.229 1.083,0.281 10 false B142 5.094,0.198 6.177,0.479 1.083,0.281 10 false 80 5.052,0.75 6.135,1.031 1.083,0.281 10 false 102 5.448,0.396 6.531,0.677 1.083,0.281 10 false CAN+ 5.448,0.948 6.531,1.229 1.083,0.281 10 false CAN- 5.427,2.135 6.51,2.417 1.083,0.281 10 false MREL 5.438,3.156 6.521,3.438 1.083,0.281 10 false E01 4.667,2.115 5.75,2.396 1.083,0.281 10 false V-3 4.635,3.156 5.719,3.438 1.083,0.281 10 false V-40 5.01,2.115 6.094,2.396 1.083,0.281 10 false A115 5.021,3.156 6.104,3.438 1.083,0.281 10 false A115 2.156,4.354 4.813,4.656 2.656,0.302 10 false : CAN Communication Line 2.24,1.406 3.844,1.781 1.604,0.375 10 false EGR Valve Assembly 2.229,1.26 3.313,1.542 1.083,0.281 10 false B48 5.083,1.906 6.167,2.188 1.083,0.281 10 false 27 5.073,2.948 6.156,3.229 1.083,0.281 10 false 12 0.906,2.76 1.99,3.042 1.083,0.281 10 false P/I 0.469,3.094 1.552,3.375 1.083,0.281 10 false R/B NO. 2-B 0.469,3.729 1.552,4.01 1.083,0.281 10 false FL MAIN 5.417,2.646 6.5,2.927 1.083,0.281 10 false MREL 4.646,2.625 5.729,2.906 1.083,0.281 10 false V-23 5.01,2.625 6.094,2.906 1.083,0.281 10 false A115 5.063,2.427 6.146,2.708 1.083,0.281 10 false 26 0.865,0.604 1.948,0.885 1.083,0.281 10 false EFI NO. 3 2.938,2.104 4.021,2.385 1.083,0.281 10 false 5 3.719,2.094 4.802,2.375 1.083,0.281 10 false 3 2.938,2.521 4.021,2.802 1.083,0.281 10 false 1 3.719,2.51 4.802,2.792 1.083,0.281 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

The cause may be hard carbon upstream of the EGR valve peeling off of the EGR cooler and falling off.

·

When the ambient temperature is low, the inside of the EGR valve may freeze, causing these DTCs to be output. However, when the inside of the EGR valve thaws, the system will return to normal.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P1458 or P1459 is output A
DTC P1458 or P1459 and other DTC are output B




A

2.CHECK EGR VALVE ASSEMBLY

B

2.CHECK EGR VALVE ASSEMBLY
a.

Check the valve sealing face and gas passageway for soot accumulation and damage due to foreign substances.


b.

Check if there is soot obstructing the exhaust gas passageway inlet or outlet.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (EGR VALVE ASSEMBLY CONNECTOR)

NG

10.REPAIR OR REPLACE EGR VALVE ASSEMBLY
3.CHECK CONNECTOR CONNECTION CONDITION (EGR VALVE ASSEMBLY CONNECTOR)
a.

Check the connector connection for the EGR valve assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.CHECK EGR VALVE ASSEMBLY

NG

9.CONNECT SECURELY
4.CHECK EGR VALVE ASSEMBLY
a.

Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


A449998C02
1.448,0.156 1.938,0.448 0.49,0.292 1.427,1.344 1.021,1.771 true 0.823,1.76 1.188,1.969 0.365,0.208 10 false +B 0.438,0.188 0.885,0.458 0.448,0.271 10 false *a 1.573,0.208 1.927,0.406 0.354,0.198 10 false B48
*a Front view of wire harness connector
(to EGR Valve Assembly Connector)


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B48-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)
a.
A449998C03
1.448,0.156 1.938,0.448 0.49,0.292 1.448,1.135 1.229,1.76 true 1.167,1.802 1.531,2.01 0.365,0.208 10 false E 0.438,0.188 0.885,0.458 0.448,0.271 10 false *a 1.573,0.208 1.927,0.406 0.354,0.198 10 false B48
*a Front view of wire harness connector
(to EGR Valve Assembly Connector)


Disconnect the EGR valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Valve Position / Data List / Actual EGR Valve Position and Target EGR Valve Position


d.

Check each step from 90 to 0% of the time lag of the target EGR valve opening and actual EGR valve opening.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 5 seconds.


HINT:

The EGR opening position changes of around 10% per step between 0 to 90%.



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

8.REPLACE EGR VALVE ASSEMBLY
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
8.REPLACE EGR VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
9.CONNECT SECURELY
a.

Connect securely the EGR valve assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
10.REPAIR OR REPLACE EGR VALVE ASSEMBLY
a.

Remove foreign substances and clean the EGR valve assembly.

HINT:

Replace the EGR valve if it is damaged.



Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END