Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM D

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  DTC CHECK / CLEAR  


INSPECTION PROCEDURE


a.

Confirm the MIL.

i.

Turn the ignition switch to ON (Do not start the engine) and confirm that the MIL (malfunction indicator light) in the indicator area lights up.


ii.

If the MIL is displayed and P204F,P205F and/or P20FE is output for the engine, check the Urea Selective Catalytic Reduction system for DTCs.

HINT:
·

If the MIL is lit, perform a Confirmation Driving Pattern to see if the malfunction is of the past or present.

·

In the case of the past malfunction, this light will turn off if a status is judged to be normal in 3 times of driving.

·

DTCs must be cleared on the GTS, after MIL comes off.






MIL ILLUMINATION PATTERN


a.

MIL (Malfunction Indicator Lamp) displays according to the vehicle condition.

HINT:

MIL display depends on malfunction class of each DTC.


Malfunction Class Requirement
Class A Malfunction where exhaust gas components exceed the OBD threshold
Class B1 Malfunction where exhaust gas components may exceed the OBD threshold
Class B2 Malfunction where it is predicted that exhaust gas components will not reach a level that exceeds the OBD threshold
Class C Malfunction where it is predicted that exhaust gas components will not reach a level that exceeds the regulation value

A446861E02
2.094,3.042 3.042,3.385 3.042,3.385 3,3.042 false 2.479,3.031 3.021,3.365 false 1.448,3.01 1.49,3.333 false 0.771,2.99 0.542,3.365 false 0.365,0.625 1.135,0.823 0.771,0.198 10 false IG ON 4.24,0.594 5.615,0.792 1.375,0.198 10 false Engine ON 0.354,1.24 1.198,1.625 0.844,0.385 10 false (1): Bulb test 1.427,1.208 4.635,1.406 3.208,0.198 10 false (2): Readiness status 3.198,1.208 4.125,1.844 0.927,0.635 10 false (3): MIL status (Engine OFF) 5.604,1.177 6.563,1.813 0.958,0.635 10 false (4): MIL status (Engine ON) 0.115,0.063 2.177,0.5 2.063,0.438 10 false MIL Illumination Pattern: 0.156,2.042 0.396,2.594 0.24,0.552 10 false MIL ON 0.156,2.729 0.479,3.073 0.323,0.344 10 false MIL OFF 6.292,2.885 7.063,3.531 0.771,0.646 10 false Time [sec.] 4.219,3.385 6.625,3.74 2.406,0.354 10 false Example: In case of "No malfunction" 2.844,3.385 3.781,3.604 0.938,0.219 10 false 5 seconds 1.208,3.365 2.146,3.583 0.938,0.219 10 false 10 seconds 0.25,3.365 1.188,3.583 0.938,0.219 10 false 5 seconds


b.

Refer to below for the relation between MIL display of (1) to (4) and its description.

(1): Bulb test

Bulb operational: MIL ON

Bulb non operational: MIL OFF

HINT:

If the MIL is not illuminated, check the MIL circuit.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>MIL Circuit



(2): Readiness status

A446862E02
1.979,0.823 3.354,1.021 1.375,0.198 10 false Readiness 5.375,0.823 6.51,1.167 1.135,0.344 10 false Readiness status 0.208,1.896 1.479,2.635 1.271,0.74 10 false Readiness "Ready" 1.854,1.844 4.677,2.479 2.823,0.635 10 false In case of the readiness for all monitored components is complete. 5.729,1.198 6.365,1.604 0.635,0.406 10 false Ready 5.656,3.302 6.531,3.698 0.875,0.396 10 false Not ready 5.667,2.771 6.5,3.219 0.833,0.448 10 false 5 seconds 5.646,4.854 6.479,5.302 0.833,0.448 10 false 5 seconds 0.354,3.896 1.333,4.604 0.979,0.708 10 false Readiness "Not Ready" 1.802,3.781 4.625,4.417 2.823,0.635 10 false In case of the readiness for one or more of the monitored components is not complete.

HINT:

There are some items that cannot be determined if the vehicle is not driven during troubleshooting. Therefore, when the ignition switch is normally turned to ON, the MIL blinks 5 times to indicate Readiness "Not Ready".

(Even though it indicates "Not Ready", this is not a malfunction.)


(3): MIL status (Engine OFF)

HINT:
·

This sequence is repeated until the engine starts or the ignition switch is turned off.

·

For "Class B1", the MIL status changes from Mode 3 to Mode 4 (continuous illumination) if the cumulative elapsed time exceeds 200 hours after it is detected.



A446863E04
0.635,1.083 1.708,1.281 1.073,0.198 10 false Class A 0.25,1.438 1.74,1.844 1.49,0.406 10 false Class B1 (200 hours or more) 0.375,2.604 1.667,3.156 1.292,0.552 10 false Class B1 (Less than 200 hours) 0.563,3.281 2.021,3.594 1.458,0.313 10 false Class B2 0.615,4.885 2.073,5.198 1.458,0.313 10 false Class C 0.656,0.292 1.427,0.49 0.771,0.198 10 false Class 3.76,0.271 5.292,0.469 1.531,0.198 10 false MIL status 2.021,0.948 2.938,1.146 0.917,0.198 10 false MIL ON 2.01,1.927 2.927,2.125 0.917,0.198 10 false MIL OFF 2,2.594 2.917,2.792 0.917,0.198 10 false MIL ON 2.052,4.385 2.969,4.583 0.917,0.198 10 false MIL ON 2.031,6.115 2.948,6.313 0.917,0.198 10 false MIL ON 1.99,3.479 2.906,3.677 0.917,0.198 10 false MIL OFF 2.031,5.333 2.948,5.531 0.917,0.198 10 false MIL OFF 2.01,7.042 2.927,7.24 0.917,0.198 10 false MIL OFF 3.021,3.792 4.396,3.99 1.375,0.198 10 false 5 seconds 3.771,3.792 5.146,3.99 1.375,0.198 10 false 5 seconds 3.594,5.604 4.969,5.802 1.375,0.198 10 false 5 seconds 3.396,7.292 4.771,7.49 1.375,0.198 10 false 5 seconds 2.833,5.594 4.208,5.792 1.375,0.198 10 false 3 seconds 2.656,7.292 4.031,7.49 1.375,0.198 10 false 1 second 0.5,6.521 1.625,7.125 1.125,0.604 10 false No malfunction 1.927,0.635 2.844,0.833 0.917,0.198 10 false Mode 4 1.896,2.375 2.813,2.573 0.917,0.198 10 false Mode 3 1.875,5.844 2.792,6.042 0.917,0.198 10 false Mode 1 1.865,4.104 2.781,4.302 0.917,0.198 10 false Mode 2

(4): MIL status (Engine ON)

HINT:

For "Class B1", the MIL status changes from Mode 3 to Mode 4 (continuous illumination) if the cumulative elapsed time exceeds 200 hours after it is detected.


A446864E04
0.813,1.167 1.885,1.365 1.073,0.198 10 false Class A 0.396,1.469 1.875,1.938 1.479,0.469 10 false Class B1 (200 hours or more) 0.448,2.604 1.76,3.208 1.313,0.604 10 false Class B1 (Less than 200 hours) 0.573,3.365 2.031,3.677 1.458,0.313 10 false Class B2 0.615,4.885 2.073,5.198 1.458,0.313 10 false Class C 3.583,0.219 5.115,0.417 1.531,0.198 10 false MIL status 0.792,0.219 2.323,0.417 1.531,0.198 10 false Class 2.781,0.625 4.313,0.823 1.531,0.198 10 false Engine ON 2.99,3.51 4.521,3.708 1.531,0.198 10 false 15 seconds 0.573,6.563 2.104,6.76 1.531,0.198 10 false No malfunction 2.021,1.99 3.552,2.188 1.531,0.198 10 false MIL OFF 2.042,1.135 3.573,1.333 1.531,0.198 10 false MIL ON 2.063,2.583 3.594,2.781 1.531,0.198 10 false MIL ON 2.01,4.427 3.542,4.625 1.531,0.198 10 false MIL ON 2.031,6.219 3.563,6.417 1.531,0.198 10 false MIL ON 2.042,3.365 3.573,3.563 1.531,0.198 10 false MIL OFF 2.031,7.083 3.563,7.281 1.531,0.198 10 false MIL OFF 1.958,0.583 2.875,0.781 0.917,0.198 10 false Mode 4 1.958,2.333 2.875,2.531 0.917,0.198 10 false Mode 3 1.969,4.104 2.885,4.302 0.917,0.198 10 false Mode 2 1.979,5.865 2.896,6.063 0.917,0.198 10 false Mode 1




CHECK DTC


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


e.

Check the DTC(s) and Freeze Frame Data, and then write them down.

HINT:
GTS Display Description
Test Failed Shows the malfunction judgment results during the current trip.
Pending Shows the malfunction judgment results up to now. (Indicates the possibility of a malfunction when no DTC is confirmed.)
Confirmed Shows the DTCs confirmed up to now. (The number of current trips differs for each DTC.)





CLEAR DTC (Using GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


e.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.