Home › Engine / Hybrid System › N04C-WA (EMISSION CONTROL) › UREA SELECTIVE CATALYTIC REDUCTION SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082614 N04C-WA EMISSION CONTROL _0400651 UREA SELECTIVE CATALYTIC REDUCTION SYSTEM C

N04C-WA EMISSION CONTROL  UREA SELECTIVE CATALYTIC REDUCTION SYSTEM  P206B64  Reductant Quality Sensor Circuit Range/Performance Signal Plausibility Failure  


DESCRIPTION

With presence of urea solution and when purifying rate diagnostic is normal.

·

Abnormality determination is made based on the propriety of urea solution type.

·

Abnormality determination is made based on the propriety of urea solution concentration.


In case without urea solution.

·

Abnormality determination is made whether or not the urea solution type is liquid.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory
P206B64 Reductant Quality Sensor Circuit Range/Performance Signal Plausibility Failure Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is 9 V to 16 V.

·

Urea solution is not frozen.

·

In case with the water feed judgment, sufficient wait time (577 seconds) has elapsed.

·

Remaining amount of urea solution is 100%.


Malfunction Status:
·

With urea solution in the tank.

-

When purifying rate is normal, detection is made that the urea solution concentration of lower than 10%.


·

Without urea solution in the tank.

-

Urea solution is detected to be in the liquid form.



Malfunction Duration:
·

-


·

Urea solution

·

Urea solution quality sensor (urea sensor assembly)


Class C AdBlue consumption warning light:
Comes on
DTC stored

MONITOR DESCRIPTION

Reset condition

After having restored to the normal conditions.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P206B64 Ignition switch ON for 577 seconds or more.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK UREA SOLUTION
a.

Measure the concentration of urea solution by the urea concentration meter in the urea solution tank.

NOTICE:

Transfer the urea solution in the urea solution tank into a different container, and then measure the concentration.



Standard:
Condition Specified Condition
Urea solution temperature:
-8 to 40°C
Normal urea solution concentration:
28.4 to 35.2%


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REDUCTANT DENSITY)

NG

3.READ VALUE USING GTS (REDUCTANT DENSITY)
2.READ VALUE USING GTS (REDUCTANT DENSITY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Density.


e.

Read the value.

Standard:
Condition Specified Condition
Urea solution temperature:
-8 to 40°C
Normal urea solution concentration:
28.4 to 35.2%



Result:
Proceed to
OK
NG



OK

NG

4.REPLACE UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY)
3.READ VALUE USING GTS (REDUCTANT DENSITY)
a.

Replace the urea solution with the new one.

NOTICE:

If there are air bubbles in the urea solution, accurate measurements cannot be obtained. Therefore, slowly refill the urea solution in the tank.



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Density.


f.

Read the value.

Standard:
Condition Specified Condition
Urea solution temperature:
-8 to 40°C
Normal urea solution concentration:
28.4 to 35.2%



Result:
Proceed to
OK
NG



OK

NG

4.REPLACE UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY)
4.REPLACE UREA SOLUTION QUALITY SENSOR (UREA SENSOR ASSEMBLY)
a.

Replace the urea solution quality sensor (urea sensor assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

NOTICE:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P206B64)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P206B64)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Trouble Codes.


f.

Read the DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END