Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P20EE  SCR NOx Catalyst Efficiency Below Threshold Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20EE SCR NOx Catalyst Efficiency Below Threshold Bank 1 Diagnosis Condition:
·

The engine speed remains at 700 rpm or more for 600 seconds or more.


·

The conditions described below remain for 60 seconds or more.

-

The exhaust gas flow rate is 190 kg/h or more and below 1000 kg/h.

-

The No. 5 exhaust gas temperature input by the DCU is 210°C (410°F) or more and below 270°C (518°F).

-

The NOx before the SCR catalyst is 50 ppm or more and below 1000 ppm.

-

The target NOx purification efficiency is 20 ppm or less.

-

The No. 2 fuel injector quantity is in the range of 20 mm3/st to 160 mm3/st.

-

The actual ratio of urea solution is 80% or more and 120% or less.

-

The calculated HC value is below 0.1 g.

-

The nitrogen oxides sensor values (both before and behind the SCR catalyst) continue to be steady for 120 seconds or more.

-

DPR work.



Malfunction Status:

(The difference obtained by subtracting the average NOx purification efficiency from the target NOx purification efficiency) continues to be 0.6 or less for 5 seconds or more.


Malfunction Duration:

5 seconds or more


·

Urea solution

·

No. 1 nitrogen oxides sensor

·

No. 2 nitrogen oxides sensor

·

Mass air flow meter

·

No. 5 exhaust gas temperature sensor

·

No. 2 exhaust pipe converter assembly


Class B1 DTC stored

MONITOR DESCRIPTION

·

Deterioration of SCR catalyst is determined by a drop in the purification efficiency.

·

Purification efficiency is calculated by upstream and downstream nitrogen oxides sensor.

·

Besides other factors, purification efficiency may drop due to the increase or decrease of urea solution amount supplied, a deviation in NH3 absorption to the sensing unit.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20EE PM forced regeneration

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK UREA SOLUTION (AdBlue)
a.

Measure the urea solution concentration.

Standard values:

30 to 35%


HINT:

If the urea solution concentration is below the standard, drain the urea solution through the tank drain with the ignition switch ON, and then refill the tank with at least 5 liters of urea solution.

Afterward, drive the vehicle and check if the problem does not recur under driving conditions.



Result:
Proceed to
OK
NG



OK

2.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)

NG

30.REPLACE UREA SOLUTION (AdBlue)
2.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


e.

Read the value displayed on the GTS.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

3.CHECK MASS AIR FLOW METER

NG

29.REPLACE INJECTOR ASSEMBLY
3.CHECK MASS AIR FLOW METER
a.

Check the installation of the mass air flow meter.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the mass air flow meter.


Result:
Proceed to
OK
NG



OK

4.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSOR)

NG

27.REPAIR OR REPLACE MASS AIR FLOW METER
4.CHECK CONNECTOR CONNECTION CONDITION (NO. 5 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection for the No. 5 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

24.CONNECT SECURELY
5.CHECK NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 5 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the No. 5 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR

NG

21.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
6.INSPECT NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

7.INSPECT UREA SOLUTION PIPE

NG

13.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
7.INSPECT UREA SOLUTION PIPE
a.

Check the urea solution pipe (pressure line) and check if there are no disconnections, clogging, corrosion, or cracks.


Result:
Proceed to
OK
NG



OK

8.INSPECT UREA INJECTOR SET

NG

28.REPLACE UREA SOLUTION PIPE
8.INSPECT UREA INJECTOR SET
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Level.


e.

Remove the urea injector assembly from the center exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:
·

Do not disconnect the urea injector set from the urea tube with heater assembly.

·

Use a cover, etc., to prevent foreign matter from entering the exhaust pipe.




f.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 3.


g.

Perform "Pattern 3" and check the urea injection.

OK:

Urea solution injects from urea injector set.



h.

Reinstall the urea injector set.


Result:
Proceed to
OK
NG



OK

9.INSPECT EXHAUST PIPE

NG

22.INSPECT UREA INJECTOR SET
9.INSPECT EXHAUST PIPE
a.

Make sure there is no soot leakage from the exhaust pipe outlet.


Result:
Proceed to
OK
NG



NG

10.REPLACE MONOLITHIC CONVERTER ASSEMBLY

OK

14.REPLACE NO. 1 NITROGEN OXIDES SENSOR AND NO. 2 NITROGEN OXIDES SENSOR
10.REPLACE MONOLITHIC CONVERTER ASSEMBLY
a.

Replace the monolithic converter assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
11.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

13.REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 5 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
14.REPLACE NO. 1 NITROGEN OXIDES SENSOR AND NO. 2 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor and No. 2 nitrogen oxides sensor.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.PERFORM PM FORCED REGENERATION
15.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.


Result:
Result Proceed to
DTC P20EE is output A
DTCs are not output B



A

17.REPLACE NO. 2 EXHAUST PIPE CONVERTER ASSEMBLY

B

END

17.REPLACE NO. 2 EXHAUST PIPE CONVERTER ASSEMBLY
a.

Replace the No. 2 exhaust pipe converter assembly.


Result:
Proceed to
NEXT



NEXT

18.PERFORM PM FORCED REGENERATION
18.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

19.CHECK DTC OUTPUT
19.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.


Result:
Result Proceed to
DTC P20EE is output A
DTCs are not output B



A

20.REPLACE ECM

B

END

20.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
21.REPAIR OR REPLACE NO. 5 EXHAUST GAS TEMPERATURE SENSOR
a.

Clean the sensing unit and install it properly.

HINT:

If damaged, replace the No. 5 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
22.INSPECT UREA INJECTOR SET
a.

Replace the urea injector set with a new one. (Do not install it on the muffler.)


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Data List / Reductant Level.


f.

Enter the following menus: Powertrain / Urea Selective Catalytic Reduction / Utility / Reductant Injection / Pattern 3.


g.

Perform "Pattern 3" and check the urea injection.

OK:

Urea solution injects from urea injector set.



Result:
Proceed to
OK
NG



OK

23.INSTALL UREA INJECTOR SET

NG

25.REINSTALL UREA INJECTOR SET
23.INSTALL UREA INJECTOR SET

b.

After installing the injector, idle the engine (for about 10 min.) and on GTS (Data List and Active Test) verify that the urea solution is stable between 4.5 Bar and 5.5 Bar.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
24.CONNECT SECURELY
a.

Connect securely the No. 5 exhaust gas temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
25.REINSTALL UREA INJECTOR SET

Result:
Proceed to
NEXT



NEXT

26.REPLACE UREA SOLUTION PIPE
26.REPLACE UREA SOLUTION PIPE
a.

Replace the urea solution pipe (pressure line).


b.

After replacing the pipe, idle the engine (for about 10 min.) and on GTS (Data List and Active Test) verify that the urea solution is stable between 4.5 Bar and 5.5 Bar.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
27.REPAIR OR REPLACE MASS AIR FLOW METER
a.

Repair or replace the mass air flow meter.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
28.REPLACE UREA SOLUTION PIPE
a.

Replace the urea solution pipe.


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
29.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION
30.REPLACE UREA SOLUTION (AdBlue)
a.

Replace the urea solution (AdBlue)

HINT:

If the urea solution concentration is below the standard, drain the urea solution through the tank drain with the ignition switch ON, and then refill the tank with at least 6 liters (1.59 gallons) of urea solution.

Afterward, drive the vehicle and confirm that the problem does not recur under driving conditions.



Result:
Proceed to
NEXT



NEXT

11.PERFORM PM FORCED REGENERATION