Home › Vehicle Interior › ENGINE HOOD / DOOR › AUTO CENTER DOOR (for Glide Type) › from 2019.08
RM2850E _58 Vehicle Interior _073213 ENGINE HOOD / DOOR _0356367 AUTO CENTER DOOR(for Glide Type) A

ENGINE HOOD / DOOR  AUTO CENTER DOOR(for Glide Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below are for RHD vehicles.



PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
B554672

Install the hole plug.

HINT:

Use the same procedure described for the other side.



Hide 67871B 2.INSTALL GLIDE DOOR WEATHERSTRIP

a.
B554671

Attach the 18 clips and install the glide door weatherstrip.


Hide 62927 3.INSTALL GLIDE DOOR OUTER WEATHERSTRIP

HINT:

Use the same procedure described for the glide door weatherstrip.


Hide 68799 4.INSTALL GLIDE DOOR ARM CAP

a.
B554685

Install the glide door arm cap.

HINT:

Use the same procedure described for the other side.



Hide 67025A 5.INSTALL SLIDE DOOR FRONT STOPPER SUB-ASSEMBLY

a.
B554686C01
2.042,1.635 2.198,1.833 0.156,0.198 10 false A
V113147

Install in this Direction


Install the slide door front stopper sub-assembly as shown in the illustration.

OK:
Area Standard Dimension
A 13.0 to 15.0 mm (0.512 to 0.591 in.)



b.

Tighten the nut.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 68790A 6.INSTALL GLIDE DOOR ARM ASSEMBLY

a.
B554687

Connect the glide door arm assembly with the 4 bolts to the vehicle body.

NOTICE:

Do not damage the glide door assembly and vehicle body with the glide door arm assembly.


Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.
B554649

Install the glide door arm assembly to the glide door assembly with the 6 bolts.

NOTICE:
·

Do not damage the glide door assembly and vehicle body with the glide door arm assembly.

·

Support the lower portion of the glide door assembly when connecting the glide door arm assembly, as the slide door assembly becomes unstable.

·

Work with 2 or more persons when connecting the glide door assembly in order to prevent deformation and damage.



Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


c.
B554648

Install the bolt.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 68750A 7.INSTALL GLIDE DOOR LINK ASSEMBLY

a.
B554675N01
1.438,1.083 1.594,1.281 0.156,0.198 10 false A

Loosen the 2 adjusting nuts.


b.

Adjust the glide door link assembly as shown in the illustration.

OK:
Area Standard Dimension
A 502.3 mm (1.65 ft.)



c.

Tighten the adjusting 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


d.
B554670

Connect the glide door link assembly with the 2 bolts to the vehicle body.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


e.
B554669

Install the glide door link assembly with the 2 bolts to the glide door assembly.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 69340A 8.INSTALL GLIDE DOOR REAR LOCK ASSEMBLY

Hide 69330B 9.INSTALL GLIDE DOOR FRONT LOCK ASSEMBLY

Hide 69630A 10.INSTALL GLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY

a.

Apply MP grease to the sliding parts of the glide door lock remote control assembly.


b.
B554668C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Install the glide door lock remote control assembly with the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the 2 connectors.


d.
B554679C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the snap as shown in the illustration.


e.

Attach the clamp.


f.
B554680C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the snap as shown in the illustration.


g.

Attach the clamp.


Hide 69530E 11.INSTALL GLIDE DOOR LOCK CYLINDER ASSEMBLY

a.

Apply MP grease to the sliding parts of the glide door lock cylinder assembly.


b.
B554676C01
0,0 0,0 false
V113147

Install in this Direction


Insert the glide door lock cylinder assembly to the glide door assembly as shown in the illustration.


c.
B554677C01
0,0 0,0 false
V113147

Install in this Direction


Install the retainer as shown in the illustration.


d.
B554678C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the snap as shown in the illustration.


Hide 69281 12.INSTALL GLIDE DOOR INSIDE HANDLE

a.

Apply MP grease to the sliding part of the glide door inside handle.


b.
B554681C01
0,0 0,0 false
V113147

Install in this Direction


Insert the 3 cables into the service hole and install the glide door inside handle with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.
B554682C01
1.198,2.51 1.406,2.688 0.208,0.177 10 true *a 0.781,0.74 0.99,0.938 0.208,0.198 10 true *b 0.427,1.24 0.615,1.417 0.188,0.177 10 true *c
*a Locking Cable (Orange)
*b Open Cable (Blue)
*c Close Cable (Purple)
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the 3 snaps and connect the 3 cables to the glide door lock remote control assembly as shown in the illustration.


d.

Attach the clamp.


Hide 69230A 13.INSTALL GLIDE DOOR OUTSIDE HANDLE ASSEMBLY

a.

Apply MP grease to the sliding part of the glide door outside handle assembly.


b.
B560092C01
0,0 0,0 false
V100155

Tape


Apply tape to the outside of the glide door outside handle assembly at the positon shown in the illustration and secure the glide door outside handle assembly in the neutral position.

HINT:

Use non-reside tape that is easy to peel off.



c.
B554655

Install the glide door outside handle assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 69714B 14.INSTALL REAR DOOR OPEN CONTROL LINK

a.
B554683C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Connect the rear door open control link in the direction indicated by the arrow (1) as shown in the illustration


b.

Attach the snap in the direction indicated by the arrow (2) as shown in the illustration.


c.
B560093C01
2.073,0.854 2.365,0.646 true 2.052,1.167 2.271,1.469 true 2.333,1.448 2.646,1.646 0.313,0.198 10 false *a 2.406,0.5 2.719,0.698 0.313,0.198 10 false *b
*a Cut out
*b Protrusion


When reusing the glide door lock remote control assembly:

i.

Align the position of the cut out with the position of the protrusion as shown in the illustration.



d.

Attach the clamp and install the rear door open control link.


e.
B554684C01
0,0 0,0 false
V113147

Remove in this Direction


When using a new glide door lock remote contrl assembly:

i.

Detach the claw and remove the clip.



Hide 69030B 16.INSTALL GLIDE DOOR OPEN LOCK ASSEMBLY

a.

Apply MP grease to the sliding part of the glide door open lock assembly.


b.
B554688C01
2.906,2.76 3.125,2.635 false 3.177,2.51 3.396,2.688 0.219,0.177 10 false *a 1.896,0.469 2.115,0.646 0.219,0.177 10 false A
*a Adjusting Bolt


Loosen the adjusting bolt.


c.

Adjust the cable as shown in the illustration.

OK:
Area Standard Dimension
A 56.5 to 58.3 mm (2.22 to 2.30 in.)



d.

Tighten the adjusting bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


e.
B554647

Attach the clamp.


f.

Install the glide door open lock assembly with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 67859F 17.INSTALL GLIDE DOOR LOWER HOLE COVER

a.
B556253

Attach the 4 clips and install the glide door lower hole cover.


Hide 67841A 18.INSTALL GLIDE DOOR SERVICE HOLE COVER

a.
B554689C01
2.042,1.167 2.51,1.646 0.469,0.479 2.281,1.188 2.5,1.375 0.219,0.188 10 true *a
*a Reference Point


Apply new butyl tape to the glide door assembly.

HINT:

Begin applying the butyl tape from the reference point shown in the illustration.



b.
B554690C01
0,0 0,0 false
V113147

Install in this Direction


Pass the cable of the glide door open lock assembly cable through a new glide door service hole cover.


c.
B554691C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the snap as shown in the illustration.


d.

Attach the clamp.


e.
B554692C01
0.24,0.583 0.385,0.479 false 1.521,0.25 1.635,0.344 false 3.073,0.385 3.188,0.479 false 3.031,2.865 3.167,2.948 false 0.135,0.604 0.323,0.771 0.188,0.167 10 false *a 1.354,0.125 1.542,0.292 0.188,0.167 10 false *a 3.208,0.479 3.396,0.646 0.188,0.167 10 false *a 3.146,2.958 3.333,3.125 0.188,0.167 10 false *a
*a Reference Point


Align the top of the glide door service hole cover with the reference point on the glide door assembly and install it.

NOTICE:
·

Securely install the glide door service hole cover to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the glide door service hole cover.

·

After installing the glide door service hole cover, check the seal quality.




Hide 82153 19.INSTALL REAR DOOR NO. 1 WIRE

a.
B554642C01
0,0 0,0 false
V100135

Connector
V100136

Bolt


Attach the 6 clamps and connect the rear door No. 1 wire to the glide door assembly.


b.

Connect the 2 connector and install the bolt


c.
B554641

Connect the rear door No. 1 wire to the glide door arm assembly with the 3 bolts.


d.
B554693C01
0,0 0,0 false
V113147

Install in this Direction


Attach the 3 claws and install the cover as shown in the illustration.


Hide 67680A 20.INSTALL GLIDE DOOR TRIM ASSEMBLY

a.
B554694C01
0,0 0,0 false
V113147

Install in this Direction


Attach the 12 clips and 2 claws to install the glide door trim assembly in the direction indicated by the arrow shown in the illustration


Hide 67690 21.INSTALL GLIDE DOOR LOWER TRIM ASSEMBLY

a.
B554695C01
0,0 0,0 false
V113147

Install in this Direction


Attach the 8 clips, 2 claws and 2 gudes to install the glide door lower trim assembly in the direction indicated by the arrow shown in the illustration


Hide 69207S 22.INSTALL REAR DOOR INSIDE HANDLE COVER

a.
B554696C01
0,0 0,0 false
V113147

Install in this Direction


Attach the 3 clips and 2 claws to install the rear door inside handle cover in the direction indicated by the arrow shown in the illustration.