Use the same procedure for LHD and RHD vehicles.
The procedure listed below is for RHD vehicles.
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
63310
3.REMOVE ROOF HEADLINING ASSEMBLY
65936
4.REMOVE NO. 1 CURTAIN RAIL (w/ Curtain)
Remove the 7 screws and No. 1 curtain rail.
Use the same procedure for other side.
65938
5.REMOVE NO. 3 CURTAIN RAIL (w/ Curtain)
Remove the 3 screws and No. 3 curtain rail.
65945A
6.REMOVE NO. 5 CURTAIN RAIL (w/ Curtain)
Remove the 3 screws and No. 5 curtain rail.
63930
7.REMOVE NO. 4 COOLER INNER DUCT RH (for Long Body)
|
Place Hands Here |
Remove the 4 screws.
Place your hands at the position shown in the illustration and detach the 3 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws and 3 guides and remove the No. 4 cooler inner duct RH.
63930
8.REMOVE NO. 4 COOLER INNER DUCT RH (for Super Long Body)
|
Place Hands Here |
Remove the 4 screws.
Place your hands at the position shown in the illustration and detach the 6 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws, 4 guides and remove the No. 4 cooler inner duct RH.
63917
9.REMOVE NO. 3 COOLER INNER DUCT RH
|
Place Hands Here |
Remove the 2 screws.
Place your hands at the position shown in the illustration and detach the 7 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws, 6 guides and remove the No. 3 cooler inner duct RH.
63916
10.REMOVE NO. 2 COOLER INNER DUCT RH
|
Place Hands Here |
Remove the 2 screws.
Place your hands at the position shown in the illustration and detach the 7 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws, 6 guides and remove the No. 2 cooler inner duct RH.
63915
11.REMOVE NO. 1 COOLER INNER DUCT RH
|
Place Hands Here |
Remove the 2 screws.
Place your hands at the position shown in the illustration and detach the 7 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 5 guides and remove the No. 1 cooler inner duct RH.
63940
12.REMOVE NO. 4 COOLER INNER DUCT LH (for Long Body)
|
Place Hands Here |
Remove the 4 screws.
Place your hands at the position shown in the illustration and detach the 3 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws, 3 guides and remove the No. 4 cooler inner duct LH.
63940
13.REMOVE NO. 4 COOLER INNER DUCT LH (for Super Long Body)
|
Place Hands Here |
Remove the 4 screws.
Place your hands at the position shown in the illustration and detach the 6 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws, 4 guides and remove the No. 4 cooler inner duct LH.
63917A
14.REMOVE NO. 3 COOLER INNER DUCT LH
|
Place Hands Here |
Remove the 2 screws.
Place your hands at the position shown in the illustration and detach the 7 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws, 6 guides and remove the No. 3 cooler inner duct LH.
63926
15.REMOVE NO. 2 COOLER INNER DUCT LH
|
Place Hands Here |
Remove the 2 screws.
Place your hands at the position shown in the illustration and detach the 7 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 2 claws, 6 guides and remove the No. 2 cooler inner duct LH.
63925
16.REMOVE NO. 1 COOLER INNER DUCT LH
|
Place Hands Here |
Remove the 2 screws.
Place your hands at the position shown in the illustration and detach the 7 clips.
|
Remove in this Direction |
Pull in the direction indicated by the arrow shown in the illustration, detach the 5 guides and remove the No. 1 cooler inner duct LH.
63830
17.REMOVE ROOF VENTILATOR DUCT ASSEMBLY
Disconnect the 2 drain cooler hoses from the roof ventilator duct assembly.
Disconnect the connector.
Remove the 6 bolts.
Remove the 3 clips and roof ventilator duct assembly.
|
Bolt |
|
Clip |
|
Connector | - | - |
88430B
18.REMOVE NO. 2 AIR DUCT ASSEMBLY
|
Push Direction |
for RHD:
Detach the clamp.
Remove the 2 clips and push the No. 2 air duct assembly towards the rear of the vehicle until the cooler unit assembly bracket bolt is visible.
for LHD:
Detach the clamp.
Remove the 2 clips and No. 2 air duct assembly.
88430A
19.REMOVE NO. 1 AIR DUCT ASSEMBLY
for RHD:
Remove the clip and No. 1 air duct assembly.
|
Push Direction |
for LHD:
Remove the clip and push the No. 1 air duct assembly towards the rear of the vehicle until the cooler unit assembly bracket bolt is visible.
88717B
20.DISCONNECT COOLER REFRIGERANT SUCTION PIPE B AND COOLER REFRIGERANT LIQUID PIPE D (for RHD)
Remove the packing.
Remove the bolt.
Detach the guide and remove the No. 1 cooler clamp.
Loosen the 2 union nuts and disconnect the cooler refrigerant suction pipe B and cooler refrigerant liquid pipe D
Remove the 2 O-rings from the cooler refrigerant suction pipe B and cooler refrigerant liquid pipe D.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88717A
21.DISCONNECT COOLER REFRIGERANT SUCTION PIPE A AND COOLER REFRIGERANT LIQUID PIPE C (for LHD)
Remove the packing.
Loosen the 2 union nuts and disconnect the cooler refrigerant suction pipe A and cooler refrigerant liquid pipe C
Remove the 2 O-rings from the cooler refrigerant suction pipe A and cooler refrigerant liquid pipe C.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88510
22.REMOVE COOLER UNIT ASSEMBLY
Disconnect the connector.
Remove the bolt and disconnect the ground wire.
Disconnect the 2 drain cooler hoses from the cooler unit assembly.
| *A | for RHD | - | - |
|
Clamp |
|
Connector |
| *A | for LHD | - | - |
|
Clamp |
|
Connector |
Detach the 7 clamps.
Remove the 6 bolts and cooler unit assembly.
Removing the cooler unit assembly from the vehicle must be performed by multiple people.
| *A | for RHD | - | - |
| *A | for LHD | - | - |