Home › Vehicle Interior › INTERIOR › ROOF HEADLINING › from 2019.08
RM2850E _58 Vehicle Interior _073215 INTERIOR _0356395 ROOF HEADLINING A

INTERIOR  ROOF HEADLINING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT BATTERY NEGATIVE TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE FRONT SEAT ASSEMBLY

Hide 4.REMOVE FRONT PROTECTOR ASSEMBLY RH (for RHD, w/ Protector)

Hide 5.REMOVE REAR SEAT ASSEMBLY RH

Hide 6.REMOVE REAR SEAT ASSEMBLY LH

Hide 7.REMOVE REAR NO. 8 SEAT ASSEMBLY (for 4-Passenger Seat)

Hide 46243 8.REMOVE PARKING BRAKE LEVER COVER

a.
B465984

Remove the 3 screws.


b.

Detach the claw and remove the parking brake lever cover.


Hide 58651A 9.REMOVE FRONT DOOR NO. 1 MAT PLATE

a.
B465985

Remove the 2 screws.


b.

Detach the 3 claws.


c.
B467046

Detach the 4 clamps and remove the front door No. 1 mat plate.


Hide 62311C 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B467545

Remove the front door opening trim weatherstrip RH.


Hide 73233 11.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73210 12.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

a.
B464709

Loosen the bolt and disconnect the floor anchor of the front seat outer belt assembly RH


b.
B464711

Using a moulding remover D, detach the 2 claws and open the front seat outer belt shoulder anchor cover.


c.
B464713

Loosen the bolt and disconnect the shoulder anchor of the front seat outer belt assembly RH.


Hide 62413A 13.REMOVE LOWER CENTER PILLAR GARNISH RH

a.
B467047

Detach the 4 clips and 5 claws and remove the lower center pillar garnish RH.


Hide 63951 14.REMOVE COOLER PIPE COVER

a.
B467048

Detach the 9 clips and 2 claws and remove the cooler pipe cover.


Hide 74617V 15.REMOVE ASSIST GRIP PLUG

a.
B467112

Detach the 4 claws and remove the 2 assist grip plugs.


Hide 74603 16.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

a.
B467113

Remove the 2 bolts and front assist grip sub-assembly.


Hide 62211 17.REMOVE FRONT PILLAR GARNISH RH

a.
B467114

Detach the 3 clips and 3 guides and remove the front pillar garnish RH.


Hide 62212 18.REMOVE FRONT PILLAR GARNISH LH

HINT:

Use the same procedure described for the RH side.


Hide 62425 19.REMOVE CENTER PILLAR GARNISH COVER (w/ Hand Grip Frame)

a.
B465982

Detach the 4 claws and remove the center pillar garnish cover.


Hide 74730 20.REMOVE HAND GRIP FRAME ASSEMBLY (w/ Hand Grip Frame)

a.
B465983

for Type A:

Remove the 6 bolts and hand grip frame assembly.


b.
B470873

for Type B:

Remove the 6 bolts and hand grip frame assembly.


Hide 73220 21.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 1 Seat)

a.
B464721

Using a moulding remover D, detach the 2 claws and open the front seat outer belt shoulder anchor cover.


b.
B464723

Loosen the bolt and disconnect the shoulder anchor of the front seat outer belt assembly LH.


Hide 62547B 22.REMOVE NO. 3 PILLAR GARNISH LH

a.
B467060

Detach the 4 clips and 4 claws and remove the No. 3 pillar garnish LH.


Hide 63375B 23.REMOVE NO. 1 ROOF HEADLINING MOULDING RH (w/o Rear Air Duct)

a.
B471329

Detach the 2 clips and claw and remove the No. 1 roof headlining moulding RH.


Hide 63375D 24.REMOVE ROOF HEADLINING MOULDING (w/o Rear Air Duct)

HINT:

Use the same procedure described for the RH side.


Hide 63371B 25.REMOVE NO. 1 ROOF BOARD SET MOULDING

a.
B467116

w/ Rear Air Duct:

i.

Detach the 2 claws.


ii.

Using a clip remover, detach the 7 clips and remove the No. 1 roof board set moulding.



b.
B471330

w/o Rear Air Duct:

Using a clip remover, detach the 9 clips and remove the No. 1 roof board set moulding.


Hide 65938 26.REMOVE NO. 3 CURTAIN RAIL (w/ Curtain)

a.
B470915

Remove the 3 screws and No. 3 curtain rail.


Hide 63610 27.REMOVE NO. 1 AIR OUTLET REGISTER ASSEMBLY (w/ Rear Air Duct)

HINT:

Use the same procedure for both No. 1 air outlet register assemblies.


a.
B467115

Detach the 6 claws and remove the No. 1 air outlet register assembly.


Hide 74310 28.REMOVE VISOR ASSEMBLY RH

a.
B467117

Remove the 2 screws.


b.

Detach the clip and visor assembly RH.


Hide 74320 29.REMOVE VISOR ASSEMBLY LH (w/ Passenger Side Visor)

HINT:

Use the same procedure described for the RH side.


Hide 63310A 30.REMOVE ROOF HEADLINING ASSEMBLY HOLE PLUG (w/ Cover)

a.
B467125

Detach the 2 clips and remove the roof headlining assembly hole plug.


Hide 83910G 31.REMOVE CLOCK ASSEMBLY (w/ Clock)

Hide 87810 32.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 55905H 33.REMOVE CONTROL KNOB SUB-ASSEMBLY (w/o Rear Air Duct)

a.
B470904

Remove the control knob sub-assembly.


Hide 63812 34.REMOVE NO. 2 ROOF VENTILATOR COVER (w/o Rear Air Duct)

a.
B470905

Detach the 2 clips and 2 claws and remove the No. 2 roof ventilator cover.


Hide 63656D 35.REMOVE CENTER AIR INTAKE COVER (w/ Rear Air Duct)

a.
B467118

Detach the 3 clips and guide and remove the center air intake cover.


Hide 63651B 36.REMOVE AIR INTAKE NET (w/ Rear Air Duct)

HINT:

Use the same procedure for both air intake net.


a.
B467120

Detach the 9 clips and remove the air intake net.


Hide 63310 37.REMOVE ROOF HEADLINING ASSEMBLY

a.

w/ Rear Air Duct:

i.
B467121

Remove the 6 clips.


ii.
B467122C03
2.188,1.188 1.927,1.188 1.927,1.188 1.719,0.719 true 1.823,2.375 1.979,2.125 1.979,2.125 2.271,2.125 false 2.26,1.094 2.573,1.333 0.313,0.24 10 false *1 2.333,2.021 2.542,2.25 0.208,0.229 10 false *a
*1 Plate
*a Hook


Remove the 4 clips and 2 plates.

HINT:

The clips indicated by the white arrows have plates between the roof headlining assembly and body. Be careful not to let them fall.



iii.

Detach the 3 clips and 8 claws.


iv.

Detach the hook.


v.
B467554

Tilt the roof headlining assembly vertically to remove it from the center door.

NOTICE:
·

Make sure wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.





b.

w/o Rear Air Duct:

i.
B470906

Remove the 2 clips.


ii.
B470907C01
1.708,0.719 1.958,1.177 1.958,1.177 2.292,1.177 true 2.344,1.104 2.656,1.302 0.313,0.198 10 false *1
*1 Plate


Using a clip remover, remove the 5 clips and 2 plates.

HINT:

The clips indicated by the white arrows have plates between the roof headlining assembly and body. Be careful not to let them fall.



iii.

Detach the 3 clips.


iv.
B470914

Tilt the roof headlining assembly vertically to remove it from the center door.

NOTICE:
·

Make sure wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.





Hide 45619K 38.REMOVE KNUCKLE STOPPER COVER (w/ Room Rack)

a.
B554326

for Standard Body:

Remove the 10 knuckle stopper covers.


b.
B554327

for Long Body:

Remove the 12 knuckle stopper covers.


Hide 39.REMOVE ROOM RACK ASSEMBLY (w/ Room Rack)

HINT:

Open the back door before performing this procedure.


a.
B554326

for Standard Body:

Remove the 10 bolts and room rack assembly from the back door.

NOTICE:
·

Removing the room rack assembly from the vehicle must be performed by multiple people.

·

Do not damage the room rack assembly, body exterior or vehicle interior.




b.
B554327

for Long Body:

Remove the 12 bolts and room rack assembly from the back door.

NOTICE:
·

Removing the room rack assembly from the vehicle must be performed by multiple people.

·

Do not damage the room rack assembly, body exterior or vehicle interior.




Hide 62425 40.REMOVE CENTER PILLAR GARNISH COVER (w/ Hand Grip Frame, w/o Rear Air Duct)

HINT:

Use the same procedure to remove the center pillar garnish cover the other side.


Hide 74730 41.REMOVE HAND GRIP FRAME ASSEMBLY (w/ Hand Grip Frame, w/o Rear Air Duct)

Hide 74708 42.REMOVE NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (for RHD, Glide Type, w/o Rear Air Duct)

Hide 62989 43.REMOVE CENTER DOOR LOCK COVER (w/o Rear Air Duct)

Hide 62638A 44.REMOVE QUARTER PILLAR GARNISH RH (w/o Rear Air Duct)

Hide 62639A 45.REMOVE QUARTER PILLAR GARNISH LH (w/o Rear Air Duct)

Hide 62548B 46.REMOVE NO. 4 PILLAR GARNISH LH (w/o Rear Air Duct)

Hide 62549B 47.REMOVE NO. 5 PILLAR GARNISH LH (for Long Body, w/o Rear Air Duct)

Hide 62537B 48.REMOVE NO. 3 PILLAR GARNISH RH (w/o Rear Air Duct)

Hide 62538B 49.REMOVE NO. 4 PILLAR GARNISH RH (w/o Rear Air Duct)

Hide 62539B 50.REMOVE NO. 5 PILLAR GARNISH RH (for Long Body, w/o Rear Air Duct)

Hide 63377C 51.REMOVE NO. 2 ROOF HEADLINING MOULDING (w/o Rear Air Duct)

a.
B471332

Detach the 2 clips, claw and guide and remove the No. 2 roof headlining moulding.


Hide 63378C 52.REMOVE NO. 3 ROOF HEADLINING MOULDING (w/o Rear Air Duct)

HINT:

Use the same procedure to remove the No. 2 roof headlining moulding.


Hide 62451B 53.REMOVE NO. 3 ROOF SIDE RAIL GARNISH RH (w/o Rear Air Duct)

Hide 62451E 54.REMOVE REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)

Hide 62431F 55.REMOVE ROOF SIDE RAIL GARNISH (for LHD, Long Body, w/o Rear Air Duct)

Hide 62451C 56.REMOVE REAR ROOF SIDE RAIL GARNISH RH (w/o Rear Air Duct)

Hide 62452B 57.REMOVE NO. 3 ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)

Hide 62431F 58.REMOVE ROOF SIDE RAIL GARNISH (for LHD, Long Body, w/o Rear Air Duct)

Hide 62451E 59.REMOVE REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)

Hide 62452C 60.REMOVE REAR ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)

Hide 86150 61.REMOVE NO. 1 WITH BOX SPEAKER ASSEMBLY (w/ SPEAKER)

Hide 81240J 62.REMOVE ROOM LIGHT ASSEMBLY

Hide 63372A 63.REMOVE NO. 2 ROOF BOARD SET MOULDING

a.

w/ Rear Air Duct:

i.
B467127

w/ Room Rack:

Using a clip remover, detach the 6 clips and remove the No. 2 roof board set moulding.


ii.
B467126

w/o Room Rack:

Using a clip remover, detach the 7 clips and remove the No. 2 roof board set moulding.



b.
B471331

w/o Rear Air Duct:

Using a clip remover, detach the 9 clips and remove the No. 2 roof board set moulding.


Hide 63322 64.REMOVE NO. 2 ROOF BOARD

a.

w/ Rear Air Duct:

i.
B467128

Using a clip remover, remove the 5 clips.


ii.
B467571

Remove the No. 2 roof board as shown in the illustration.

NOTICE:

Do not fold the No. 2 roof board.




b.
B470908

w/o Rear Air Duct:

Using a clip remover, remove the 6 clips and No. 2 roof board.

NOTICE:

Do not fold the No. 2 roof board.



Hide 63372A 65.REMOVE NO. 2 ROOF BOARD SET MOULDING

HINT:

Use the same procedure to remove the No. 2 roof board set moulding the other side.


Hide 63323 66.REMOVE NO. 3 ROOF BOARD

a.

w/ Rear Air Duct:

i.
B467131

Using a clip remover, remove the 5 clips.


ii.
B467579

Remove the No. 3 roof board as shown in the illustration.

NOTICE:

Do not fold the No. 3 roof board.




b.
B470909

w/o Rear Air Duct:

Using a clip remover, remove the 6 clips and No. 3 roof board.

NOTICE:

Do not fold the No. 3 roof board.



Hide 86150B 67.REMOVE NO. 2 WITH BOX SPEAKER ASSEMBLY (w/ SPEAKER)

HINT:

Use the same procedure described for the No. 1 with box speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ROOF SPEAKER>REMOVAL


Hide 63372A 68.REMOVE NO. 2 ROOF BOARD SET MOULDING (for Long Body, w/o Rear Air Duct)

HINT:

Use the same procedure to remove the No. 2 roof board set moulding the other side.


Hide 63372A 69.REMOVE NO. 2 ROOF BOARD SET MOULDING (for Super Long Body)

HINT:

Use the same procedure to remove the No. 2 roof board set moulding the other side.


Hide 63324 70.REMOVE NO. 4 ROOF BOARD (for Super Long Body)

a.
B554314

Using a clip remover, remove the 5 clips.


b.
B554315

Remove the No. 4 roof board as shown in the illustration.

NOTICE:

Do not fold the No. 4 roof board.



Hide 63372F 71.REMOVE NO. 3 ROOF BOARD SET MOULDING (w/ Rear Air Duct)

a.
B467133

w/ Room Rack:

i.

Detach the claw.


ii.

Using a clip remover, detach the 6 clips and remove the No. 3 roof board set moulding.



b.
B467132

w/o Room Rack:

i.

Detach the 2 claws.


ii.

Using a clip remover, detach the 7 clips and remove the No. 3 roof board set moulding.



Hide 63372G 72.REMOVE NO. 4 ROOF BOARD SET MOULDING (w/o Rear Air Duct)

a.
B471333

Detach the 9 clips and remove the No. 4 roof board set moulding.


Hide 63324 73.REMOVE NO. 4 ROOF BOARD

a.
B467140

except Long Body, w/ Rear Air Duct:

Using a clip remover, remove the 3 clips.


b.
B467139

for Long Body, w/ Rear Air Duct:

Using a clip remover, remove the 7 clips.


c.
B467580

w/ Rear Air Duct:

Remove the No. 4 roof board as shown in the illustration.

NOTICE:

Do not fold the No. 4 roof board.



d.
B470911

for Standard Body, w/o Rear Air Duct:

Using a clip remover, remove the 4 clips and No. 4 roof board.

NOTICE:

Do not fold the No. 4 roof board.



e.
B470910

for Long Body, w/o Rear Air Duct:

Using a clip remover, remove the 6 clips and No. 4 roof board.

NOTICE:

Do not fold the No. 4 roof board.



Hide 63315B 74.REMOVE NO. 5 ROOF HEADLINING BOARD (for Long Body, w/o Rear Air Duct)

a.
B470912

Remove the 3 clips and No. 5 roof headlining board.

NOTICE:

Do not fold the No. 5 roof board.



Hide 65939 75.REMOVE NO. 4 CURTAIN RAIL (w/ Curtain)

a.
B467557

except Long Body:

Remove the 7 screws and No. 4 curtain rail.


b.
B467136

for Long Body:

Remove the 3 screws and No. 4 curtain rail.


Hide 65937 76.REMOVE NO. 2 CURTAIN RAIL (w/ Curtain)

HINT:

Use the same procedure described for the No. 4 curtain rail.


Hide 65905B 77.REMOVE WINDOW CURTAIN RAIL SUB-ASSEMBLY (w/ Curtain)

a.
B467137

Remove the 6 screws and 2 window curtain rail sub-assemblies.


Hide 63349A 78.REMOVE REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)

a.
B467135

Detach the 13 clips and remove the rear roof headlining garnish.


Hide 62487A 79.REMOVE INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)

a.
B467073

Detach the 2 clips and 3 claws and remove the inner roof side garnish cover RH.


Hide 62488A 80.REMOVE INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)

HINT:

Use the same procedure described for the RH side.


Hide 64735A 81.REMOVE CENTER BACK INNER RAIL GARNISH (for Lift Up Type)

a.
B467086

for Tumble Type 4 - Passenger Seat:

i.

Detach the 10 claws.


ii.

Detach the 12 clips and 2 guides and remove the center back inner rail garnish.


iii.

Disconnect the connector.



b.
B470869

for Fixed Type 4 - Passenger Seat:

i.

Detach the 4 claws.


ii.

Detach the 8 clips and remove the center back inner rail garnish.


iii.

Disconnect the connector.



Hide 62471D 82.REMOVE REAR UPPER PILLAR GARNISH RH

a.
B467081

Remove the clip.


b.

Detach the 11 clips and remove the rear upper pillar garnish RH.


Hide 62472D 83.REMOVE REAR UPPER PILLAR GARNISH LH

HINT:

Use the same procedure described for the RH side.


Hide 63316A 84.REMOVE NO. 6 ROOF HEADLINING

a.

w/ Rear Air Duct:

i.
B467138C03
1.708,0.74 1.938,1.198 1.938,1.198 2.24,1.198 true 2.292,1.104 2.604,1.302 0.313,0.198 10 false *1
*1 Plate


for Double Swing Out Type:

1.

Detach the 8 claws.

2.

Using a clip remover, remove the 7 clips, plate and No. 6 roof headlining.


NOTICE:
·

Make sure wrinkles do not form in the No. 6 roof headlining during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.



HINT:

The clips indicated by the white arrow have plates between the No. 6 roof headlining and body. Be careful not to let them fall.



ii.
B467134C03
2.229,1.198 1.938,1.198 1.938,1.198 1.75,0.719 true 2.302,1.115 2.615,1.313 0.313,0.198 10 false *1
*1 Plate


for Lift Up Type:

1.

Detach the 8 claws.

2.

Using a clip remover, remove the 8 clips, plate and No. 6 roof headlining.


NOTICE:
·

Make sure wrinkles do not form in the No. 6 roof headlining during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.



HINT:

The clips indicated by the white arrow have plates between the No. 6 roof headlining and body. Be careful not to let them fall.




b.

w/o Rear Air Duct:

i.
B470913C01
2.104,1.219 1.948,1.219 1.948,1.219 1.802,0.875 true 2.167,1.146 2.417,1.344 0.25,0.198 10 true *1
*1 Plate


Remove the 8 clips, plate and No. 6 roof headlining.

NOTICE:
·

Make sure wrinkles do not form in the No. 6 roof headlining during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or anything as it may become bent ordamaged.

·

Do not damage the roof headlining assembly or vehicle interior.



HINT:

The clips indicated by the white arrow have plates between the No. 6 roof headlining and body. Be careful not to let them fall.