Home › Engine / Hybrid System › N04C-UH (LUBRICATION) › OIL AND OIL FILTER › 2019.08–2021.01
RM2850E _51 Engine / Hybrid System _073179 N04C-UH LUBRICATION _0356103 OIL AND OIL FILTER A

N04C-UH LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will cause the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants that may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

·

For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 58521D 1.REMOVE ENGINE SERVICE HOLE COVER MAT (w/ Carpet)

a.

Remove the engine service hole cover mat.


Hide 58410 2.REMOVE ENGINE SERVICE HOLE COVER

a.

Detach the 2 catch hooks, 2 guides and remove the engine service hole cover.


Hide 58734B 3.REMOVE ENGINE SERVICE COVER REAR WEATHERSTRIP

a.

Remove the engine service cover rear weatherstrip.


Hide 51441D 4.REMOVE NO. 1 ENGINE UNDER COVER (for Plastic Type)

a.

Remove the 4 screws, 6 bolts and No. 1 engine under cover.


Hide 5.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the drain plug and gasket from the oil pan and drain the engine oil into a container.


c.

Clean the drain plug.


d.

Install the drain plug with a new gasket.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 15613 6.REMOVE OIL FILTER ELEMENT

a.
A446912C02
2.531,0.469 2.375,0.469 2.375,0.469 2.052,0.813 false 2.583,1 2.417,1 2.417,1 1.802,1.323 false 0.917,1.583 1.083,1.583 1.083,1.583 1.5,1.833 false 2.594,0.406 2.833,0.656 0.24,0.25 10 false *a 0.719,1.5 1.052,1.75 0.333,0.25 10 false *c 2.625,0.917 2.958,1.167 0.333,0.25 10 false *b
*a Drain Adapter
*b Pipe
*c Hose


Connect a hose with an inner diameter of 12 mm (0.472 in.) to the pipe.

HINT:

Firmly insert the hose until it contacts the base of the drain adapter pipe.



b.
A446913

Remove the oil filter plug and O-ring (for plug) from the oil filter cap assembly.

HINT:

After removing the oil filter plug, a small amount of oil may drip out, so wipe it with a cloth.



c.
A446914C02
2.302,1.917 2.469,1 2.469,1 2.635,1 true 1.5,2.833 1.667,2.833 1.667,2.833 2.083,2.333 true 1.479,3.167 1.646,3.167 1.646,3.167 2.396,2.833 true 2.698,0.948 3,1.167 0.302,0.219 10 false *1 1.344,2.74 1.625,3 0.281,0.26 10 false *a 1.313,3.094 1.646,3.333 0.333,0.24 10 false *b
*1 Oil Filter Cap Assembly
*a Drain Adapter
*b Pipe


Install the drain adapter and its installed hose to the oil filter cap assembly, and then tighten it until the drain adapter contacts the surface. After making contact, tighten the drain adapter until it can no longer be turned by hand.

NOTICE:

Do not install and tighten the drain adapter using tools such as pliers. Otherwise, the drain adapter may be damaged.


HINT:

Use a container to catch the draining engine oil.



d.
A446915

Check that the engine oil has been drained and remove the drain adapter.


e.
A446916

Remove the oil filter cap assembly.


f.
A446917C02
0.688,0.5 1.354,0.5 false 2.177,0.865 2.76,0.865 false 0.51,0.438 0.833,0.667 0.323,0.229 10 false *1 2.813,0.792 3.104,1.031 0.292,0.24 10 false *2
*1 Oil Filter Element
*2 O-Ring (for cap)


Remove the oil filter element and O-ring (for cap) from the oil filter cap assembly.

NOTICE:

To prevent damage to the O-ring groove, remove the O-ring (for cap) by hand and do not use any tools.



Hide 15613 7.INSTALL OIL FILTER ELEMENT

a.

Clean the inside of the oil filter cap assembly, the threads and O-ring groove.


b.
A446918C02
1.469,0.615 1.583,0.25 1.583,0.25 1.75,0.25 false 1.75,1 1.833,1 1.833,1 2,0.667 false 1.792,0.177 2.083,0.396 0.292,0.219 10 false *1 1.573,0.927 1.823,1.198 0.25,0.271 10 false *1 0.906,1.906 1.167,2.073 0.26,0.167 10 false *a 2.438,1.927 2.667,2.094 0.229,0.167 10 false *b
*1 O-Ring (for cap)
*a CORRECT
*b INCORRECT


Apply a light coat of engine oil to a new O-ring (for cap), and install it to the oil filter cap assembly.

NOTICE:
·

Be sure to install the O-ring in the proper position, otherwise engine oil may leak.

·

Do not twist the O-ring.



HINT:

Attach a new O-ring after brakes cleaner volatilized enough when use brakes cleaner to prevent the deterioration of the O-ring.



c.

Set a new oil filter element to the oil filter cap assembly.


d.

Remove any dirt or foreign matter from the installation surface and inside of the engine.


e.

Again apply a light coat of engine oil to the O-ring (for cap), and install the oil filter cap assembly.

NOTICE:

Make sure that the O-ring (for cap) is not pinched.



f.
A446919C02
2.563,2.833 2.896,2.833 false 2.365,2.281 2.583,2.281 true 2.667,1.688 2.917,1.688 false 2.948,2.781 3.26,3 0.313,0.219 10 false *1 2.198,2.229 2.5,2.5 0.302,0.271 10 false *2 2.958,1.635 3.24,1.875 0.281,0.24 10 false *3 3,2.333 3.26,2.542 0.26,0.208 10 false *a
*1 Oil Filter Cap Assembly
*2 O-Ring (for cap)
*3 Oil Cooler Cover Sub-assembly
*a No Gap


Tighten the oil filter cap assembly.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

After tightening the oil filter cap assembly, check for gaps between the installation surfaces and protrusion of O-ring (for cap).



g.
A446920C02
2.417,1.51 2.5,1.51 2.5,1.51 2.708,1.563 true 2.271,1.427 2.563,1.677 0.292,0.25 10 false *1
*1 O-Ring (for plug)


Apply a light coat of engine oil to a new O-ring (for plug), and install it to the oil filter cap assembly.

NOTICE:

Remove any dirt or foreign matter from the installation surface.



h.

Install the oil filter plug to the oil filter cap assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Make sure that the O-ring (for plug) is not pinched.



Hide 8.ADD ENGINE OIL

a.

Add fresh oil and install the oil filler cap sub-assembly.

Engine Oil:
Oil Grade
API CJ-4 or CK-4, ACEA E-6 or E-9
JASO DH-2
·

5W-30

·

10W-30

·

15W-40




Capacity:
Item Fill amount
Drain and refill with oil filter change 7.0 liters (7.4 US qts, 6.2 Imp. qts)
Drain and refill without oil filter change 5.8 liters (6.1 US qts, 5.1 Imp. qts)
Dry fill 8.4 liters (8.9 US qts, 7.4 Imp. qts)



Hide 9.INSPECT FOR OIL LEAK

a.

Warm up the engine and check for engine oil leaks.


Hide 51441D 11.INSTALL NO. 1 ENGINE UNDER COVER (for Plastic Type)

a.

Install the No. 1 engine under cover with the 4 screws and the 6 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 58734B 12.INSTALL ENGINE SERVICE COVER REAR WEATHERSTRIP

a.

Install the rear engine service cover weatherstrip.


Hide 58410 13.INSTALL ENGINE SERVICE HOLE COVER

a.

Attach the 2 guides, 2 catch hooks and install the engine service hole cover.


Hide 58521D 14.INSTALL ENGINE SERVICE HOLE COVER MAT (w/ Carpet)

a.

Install the engine service hole cover mat.