Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  U0100  Engine ECU Communication  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0100 Engine ECU Communication The transmission control ECU assembly is unable to receive data from the ECM.
·

Local bus main line and branch line

·

Transmission control ECU assembly

·

Translate ECU assembly

·

No. 7 CAN junction connector

·

No. 6 CAN junction terminal


DTC Output from:

Transmission control ECU assembly



WIRING DIAGRAM

C419843E01
5.229,1.448 5.688,1.646 0.458,0.198 10 false B133 5.24,1.635 6.958,2.042 1.719,0.406 10 false Transmission Control ECU Assembly 5.781,1.396 6.24,1.594 0.458,0.198 10 false CAN- 5.75,0.781 6.208,0.979 0.458,0.198 10 false CAN+ 5.448,1.177 5.906,1.375 0.458,0.198 10 false 21 5.458,0.75 5.917,0.948 0.458,0.198 10 false 20 3.823,0.74 4.281,0.938 0.458,0.198 10 false 1 3.833,1.156 4.292,1.354 0.458,0.198 10 false 12 3.146,0.729 3.604,0.927 0.458,0.198 10 false 2 3.094,1.156 3.552,1.354 0.458,0.198 10 false 13 1.271,0.74 1.729,0.938 0.458,0.198 10 false 17 1.313,1.156 1.771,1.354 0.458,0.198 10 false 28 0.167,1.427 1.146,1.677 0.979,0.25 10 false V9 0.167,1.625 2.177,1.917 2.01,0.292 10 false Translate ECU Assembly 0.854,0.865 1.833,1.115 0.979,0.25 10 false CANP 0.844,1.281 1.823,1.531 0.979,0.25 10 false CANN 3.094,2.823 3.552,3.021 0.458,0.198 10 false 14 3.146,2.427 3.604,2.625 0.458,0.198 10 false 3 1.344,2.417 1.802,2.615 0.458,0.198 10 false 3 1.344,2.833 1.802,3.031 0.458,0.198 10 false 2 0.813,2.438 1.375,2.635 0.563,0.198 10 false CANH 0.865,3.063 1.427,3.26 0.563,0.198 10 false CANL 0.125,3.438 1.104,3.688 0.979,0.25 10 false A126 0.104,3.615 2.313,3.927 2.208,0.313 10 false No. 6 CAN Junction Terminal 2.865,3.208 3.844,3.458 0.979,0.25 10 false A123 2.854,3.385 5.063,3.698 2.208,0.313 10 false No. 7 CAN Junction Connector

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

According to the display on the GTS, select "Health Check".


e.

Read the DTCs.


Result:
Result Proceed to
Only transmission control ECU assembly outputs U0100 A
U0100 or communication malfunction DTC is also output from somewhere other than transmission control ECU assembly B



A

2.CHECK FOR OPEN IN CAN BUS WIRE

B

2.CHECK FOR OPEN IN CAN BUS WIRE
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C407778C03
2.604,0.74 3.031,0.948 0.427,0.208 5.698,0.708 6.125,0.917 0.427,0.208 3.052,1.729 3.385,0.635 3.385,0.635 3.552,0.635 true 3.063,1.802 3.146,2.542 3.146,2.542 3.313,2.542 true 5.906,1.365 5.5,1 5.5,1 5.333,1 true 6.427,1.75 6.125,2.26 6.125,2.26 5.958,2.26 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 2.74,0.781 3.052,0.979 0.313,0.198 10 false V9 3.625,0.573 4.042,0.823 0.417,0.25 10 false CANP 3.375,2.469 3.823,2.677 0.448,0.208 10 false CANN 4.958,0.583 5.271,0.781 0.313,0.198 10 false *b 5.792,0.74 6.104,0.938 0.313,0.198 10 false J45 5.083,0.938 5.5,1.188 0.417,0.25 10 false CG 5.667,2.188 6.115,2.396 0.448,0.208 10 false BAT
*a Component with harness connected
(to Translate ECU Assembly)
*b Front view of DLC3


Standard Resistance:
Tester Connection Condition Specified Condition Result
V9-17 (CANP) - V9-28 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 53 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
V9-17 (CANP) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Short to ground
V9-28 (CANN) - J45-4 (CG)
V9-17 (CANP) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
V9-28 (CANN) - J45-16 (BAT)



Result:
Proceed to
OK
NG



OK

3.CHECK CAN COMMUNICATION

NG

4.CHECK FOR CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)
3.CHECK CAN COMMUNICATION
a.
C265973N01
0.5,0.417 0.906,0.781 false 0.5,1.583 0.917,1.167 false 0.135,0.333 0.75,0.531 0.615,0.198 10 CANH 0.167,1.552 0.781,1.75 0.615,0.198 10 CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 50 μs/DIV. 2.708,0.25 3.427,0.448 0.719,0.198 10 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 GND

Using an oscilloscope, check the waveform between each connector terminal.

HINT:

Set each range of the oscilloscope as shown in the table.

Item Content
Terminal Connection B133-20 (CAN+) - Body ground
B133-21 (CAN-) - Body ground
Tester Range 1 V/DIV., 50 μs./DIV.
Vehicle Condition Ignition switch is ON


Standard:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPLACE TRANSLATE ECU ASSEMBLY

4.CHECK FOR CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

C358918C03
0.156,0.708 0.563,1.01 0.406,0.302 5.125,0.125 5.542,0.396 0.417,0.271 6.219,1.625 6.073,1.625 6.073,1.625 5.906,1.125 true 1.448,0.969 1.667,0.323 1.667,0.323 1.823,0.323 true 1.323,0.958 1.146,0.292 1.146,0.292 1,0.292 true 1.219,0.969 1.031,0.458 1.031,0.458 0.917,0.458 true 0.865,1.448 0.979,1.448 0.979,1.448 1.219,1.188 true 1.052,1.646 1.188,1.646 1.188,1.646 1.333,1.167 true 1.76,1.552 1.594,1.552 1.594,1.552 1.458,1.177 true 5.26,0.719 4.76,0.323 4.76,0.323 4.646,0.323 true 0.167,0.073 0.479,0.271 0.313,0.198 10 false *a 3.875,0.125 4.188,0.323 0.313,0.198 10 false *b 0.219,0.781 0.677,0.979 0.458,0.198 10 false A123 6.292,1.563 6.75,1.76 0.458,0.198 10 false BAT 5.229,0.188 5.688,0.385 0.458,0.198 10 false J45 0.469,0.208 1.385,0.406 0.917,0.198 10 false CANH*d 0.385,0.375 1.302,0.573 0.917,0.198 10 false CANH*c 1.875,0.25 2.792,0.448 0.917,0.198 10 false CANH*e 1.802,1.479 2.719,1.677 0.917,0.198 10 false CANL*e 0.344,1.375 1.26,1.573 0.917,0.198 10 false CANL*c 0.531,1.563 1.448,1.76 0.917,0.198 10 false CANL*d 4.396,0.26 5.313,0.458 0.917,0.198 10 false CG
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Transmission Control ECU Assembly *d to Translate ECU Assembly
*e to No. 6 CAN Junction Terminal - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A123-1 (CANH) - A123-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Transmission control ECU assembly
A123-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A123-12 (CANL) - J45-16 (BAT)
A123-1 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A123-12 (CANL) - J45-4 (CG)
A123-2 (CANH) - A123-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Translate ECU assembly
A123-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A123-13 (CANL) - J45-16 (BAT)
A123-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A123-13 (CANL) - J45-4 (CG)
A123-3 (CANH) - A123-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction terminal
A123-3 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A123-14 (CANL) - J45-16 (BAT)
A123-3 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A123-14 (CANL) - J45-4 (CG)



c.

Reconnect the No. 7 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Transmission control ECU assembly main wire) B
NG (Translate ECU assembly branch wire) C
NG (No. 6 CAN junction terminal main wire) D



A

REPAIR OR REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

5.CHECK FOR CAN BUS WIRES (TRANSMISSION CONTROL ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR CAN BUS WIRES (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

D

7.CHECK CAN BUS (NO. 6 CAN JUNCTION TERMINAL - NO. 7 CAN JUNCTION CONNECTOR)
5.CHECK FOR CAN BUS WIRES (TRANSMISSION CONTROL ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the transmission control ECU assembly connector.


b.
C422618C01
1.438,0.156 1.927,0.406 0.49,0.25 0.51,2.51 0.865,2.76 0.354,0.25 1.021,1.875 1.188,1.875 1.188,1.875 1.552,1.427 true 2.406,3.125 2.24,3.125 2.24,3.125 2.146,2.771 true 0.979,3.115 1.146,3.115 1.146,3.115 1.656,2.521 true 2.104,1.885 1.938,1.885 1.938,1.885 1.698,1.406 true 0.479,0.135 0.792,0.333 0.313,0.198 10 false *a 1.531,0.198 2.365,0.396 0.833,0.198 10 false B133 0.604,1.792 1.438,1.99 0.833,0.198 10 false CAN+ 2.469,3.052 3,3.24 0.531,0.188 10 false BAT 0.708,3.021 1.542,3.219 0.833,0.198 10 false CG 2.135,1.802 2.969,2 0.833,0.198 10 false CAN- 0.479,2.135 0.792,2.333 0.313,0.198 10 false *b 0.594,2.542 1.427,2.74 0.833,0.198 10 false J45
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-20 (CAN+) - B133-21 (CAN-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B133-20 (CAN+) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B133-21 (CAN-) - J45-16 (BAT)
B133-20 (CAN+) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
B133-21 (CAN-) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

6.CHECK FOR CAN BUS WIRES (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the translate ECU assembly connector.


b.
C422590C01
1.438,0.156 1.792,0.406 0.354,0.25 1.51,1.833 1.865,2.083 0.354,0.25 0.688,1.635 0.854,1.635 0.854,1.635 1.167,1.344 true 2.427,3.052 2.26,3.052 2.26,3.052 2.167,2.698 true 0.979,3.125 1.146,3.125 1.146,3.125 1.646,2.396 true 0.719,0.625 0.885,0.625 0.885,0.625 1.146,1.208 true 0.479,0.135 0.792,0.333 0.313,0.198 10 false *a 1.531,0.198 2.365,0.396 0.833,0.198 10 false V9 0.271,1.552 1.104,1.75 0.833,0.198 10 false CANN 2.479,2.99 3.01,3.177 0.531,0.188 10 false BAT 0.708,3.042 1.542,3.24 0.833,0.198 10 false CG 0.302,0.563 1.135,0.76 0.833,0.198 10 false CANP 0.479,1.823 0.792,2.021 0.313,0.198 10 false *b 1.604,1.865 2.438,2.063 0.833,0.198 10 false J45
*a Front view of wire harness connector
(to Translate ECU Assembly)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-17 (CANP) - V9-28 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V9-17 (CANP) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V9-28 (CANN) - J45-16 (BAT)
V9-17 (CANP) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-28 (CANN) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE TRANSLATE ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

7.CHECK CAN BUS (NO. 6 CAN JUNCTION TERMINAL - NO. 7 CAN JUNCTION CONNECTOR)
a.
C251147C20
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.927,0.25 1.448,0.427 0.521,0.177 10 false CANL 0.594,1.125 1.042,1.375 0.448,0.25 10 false CANH 2.5,0.771 2.948,1.021 0.448,0.25 10 false A126 0.531,2.563 0.979,2.813 0.448,0.25 10 false J45 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 6 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the No. 6 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A126-3 (CANH) - A126-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A126-3 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A126-2 (CANL) - J45-16 (BAT)
A126-3 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A126-2 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 6 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION TERMINAL - NO. 7 CAN JUNCTION CONNECTOR)