Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2019.08–2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area

*1: except N04C-WA

*2: for N04C-WA

ECM Communication Stop Mode Either condition is met:
·

"Engine" cannot be normally selected on the system selection screen of the GTS

·

Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS (Click here(Click here)).

·

Communication stop history for "ECM (Engine)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "ECM (Engine)" is 6 or more.) (Click here(Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table" (Click here(Click here)).


·

ECM CAN main wire or connector*1

·

ECM CAN branch wire or connector*2

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

for N04C-VQ, N04C-VL
C371330E03
0.385,1.448 0.844,1.646 0.458,0.198 10 false A85 0.385,1.615 2.135,1.833 1.75,0.219 10 false No. 66 Junction Connector 5.438,0.771 6.052,0.969 0.615,0.198 10 false CANH 5.438,1.396 6.052,1.594 0.615,0.198 10 false CANL 5.458,1.917 6.073,2.115 0.615,0.198 10 false BATT 5.458,2.385 6.073,2.583 0.615,0.198 10 false MREL 5.458,2.844 6.073,3.042 0.615,0.198 10 false +B 5.458,3.302 6.073,3.5 0.615,0.198 10 false IGSW 5.448,4.021 6.063,4.219 0.615,0.198 10 false EC 5.458,4.438 6.073,4.635 0.615,0.198 10 false E1 5.458,4.865 6.073,5.063 0.615,0.198 10 false E01 5.448,5.313 6.063,5.51 0.615,0.198 10 false E02 5.677,5.75 6.135,5.948 0.458,0.198 10 false ECM 2.271,2.813 4.417,3.01 2.146,0.198 10 false from EFI Relay 2.385,2.344 4.531,2.542 2.146,0.198 10 false to EFI Relay 2.417,1.885 4.563,2.083 2.146,0.198 10 false from Battery 2.26,3.302 4.406,3.5 2.146,0.198 10 false from IG2 Relay 3.802,1.771 5.948,1.969 2.146,0.198 10 false EFI NO.1 3.813,2.698 5.958,2.896 2.146,0.198 10 false EFI NO.2 3.823,3.177 5.969,3.375 2.146,0.198 10 false IGN NO.2 5.083,0.885 5.542,1.083 0.458,0.198 10 false A56 5.083,1.302 5.542,1.5 0.458,0.198 10 false A56 5.083,1.917 5.542,2.115 0.458,0.198 10 false A57 5.083,2.385 5.542,2.583 0.458,0.198 10 false A56 5.083,2.844 5.542,3.042 0.458,0.198 10 false A57 5.083,3.302 5.542,3.5 0.458,0.198 10 false A56 5.063,4.01 5.521,4.208 0.458,0.198 10 false A57 5.031,4.427 5.49,4.625 0.458,0.198 10 false B102 5.031,4.854 5.49,5.052 0.458,0.198 10 false B102 5.031,5.302 5.49,5.5 0.458,0.198 10 false B102 1.677,1.208 1.99,1.406 0.313,0.198 10 false 12 1.688,0.771 2,0.969 0.313,0.198 10 false 1 5.177,0.677 5.49,0.875 0.313,0.198 10 false 7 5.167,1.104 5.479,1.302 0.313,0.198 10 false 1 5.125,1.719 5.438,1.917 0.313,0.198 10 false 23 5.135,2.177 5.448,2.375 0.313,0.198 10 false 25 5.125,2.646 5.438,2.844 0.313,0.198 10 false 24 5.135,3.094 5.448,3.292 0.313,0.198 10 false 24 5.104,3.802 5.417,4 0.313,0.198 10 false 11 5.146,4.24 5.458,4.438 0.313,0.198 10 false 1 5.115,4.656 5.427,4.854 0.313,0.198 10 false 11 5.125,5.104 5.438,5.302 0.313,0.198 10 false 12

for N04C-UH
C400212E02
0.469,1.427 0.927,1.625 0.458,0.198 10 false A85 0.469,1.594 2.292,1.833 1.823,0.24 10 false No. 66 Junction Connector 3.792,1.76 5.021,1.958 1.229,0.198 10 false EFI-MAIN 2.417,1.885 4.25,2.083 1.833,0.198 10 false from Battery 2.406,2.354 4.24,2.552 1.833,0.198 10 false to EFI Relay 2.281,2.813 4.115,3.01 1.833,0.198 10 false from EFI Relay 2.167,3.281 4,3.479 1.833,0.198 10 false from IG2 Relay*1 0.823,3.771 3.479,4 2.656,0.229 10 false from ENG STOP/P LOCK NO.2 Relay*2 3.792,2.698 5.021,2.896 1.229,0.198 10 false EFI NO.2 3.74,3.167 4.969,3.365 1.229,0.198 10 false IGN NO.2*1 0.146,5.76 4.125,5.958 3.979,0.198 10 false *1: w/o Engine Stop System 0.167,6.135 3.99,6.333 3.823,0.198 10 false *2: w/ Engine Stop System 5.438,0.781 6.052,0.979 0.615,0.198 10 false CANH 5.438,1.396 6.052,1.594 0.615,0.198 10 false CANL 5.438,1.906 6.052,2.104 0.615,0.198 10 false BATT 5.448,2.365 6.063,2.563 0.615,0.198 10 false MREL 5.458,2.833 6.073,3.031 0.615,0.198 10 false +B 5.448,3.302 6.063,3.5 0.615,0.198 10 false IGSW 5.458,4.396 6.073,4.594 0.615,0.198 10 false EC 5.458,4.833 6.073,5.031 0.615,0.198 10 false E1 5.448,5.26 6.063,5.458 0.615,0.198 10 false E01 5.458,5.719 6.073,5.917 0.615,0.198 10 false E02 5.677,6.135 6.292,6.333 0.615,0.198 10 false ECM 5.083,0.885 5.542,1.083 0.458,0.198 10 false A52 5.083,1.302 5.542,1.5 0.458,0.198 10 false A52 5.083,1.917 5.542,2.115 0.458,0.198 10 false A52 5.083,2.375 5.542,2.573 0.458,0.198 10 false A54 5.083,2.833 5.542,3.031 0.458,0.198 10 false A54 5.063,4.406 5.521,4.604 0.458,0.198 10 false B60 5.083,3.302 5.542,3.5 0.458,0.198 10 false A54 5.063,4.833 5.521,5.031 0.458,0.198 10 false B60 5.073,5.25 5.531,5.448 0.458,0.198 10 false B59 5.063,5.698 5.521,5.896 0.458,0.198 10 false B59 1.677,1.198 1.99,1.396 0.313,0.198 10 false 12 1.698,0.781 2.01,0.979 0.313,0.198 10 false 1 5.115,0.667 5.427,0.865 0.313,0.198 10 false 17 5.125,1.115 5.438,1.313 0.313,0.198 10 false 28 5.156,1.708 5.469,1.906 0.313,0.198 10 false 2 5.125,2.177 5.438,2.375 0.313,0.198 10 false 13 5.156,2.635 5.469,2.833 0.313,0.198 10 false 1 5.125,3.104 5.438,3.302 0.313,0.198 10 false 16 5.094,4.198 5.406,4.396 0.313,0.198 10 false 19 5.135,4.635 5.448,4.833 0.313,0.198 10 false 7 5.146,5.063 5.458,5.26 0.313,0.198 10 false 7 5.146,5.51 5.458,5.708 0.313,0.198 10 false 6

for 2TR-FE
C371320E02
0.406,1.323 0.865,1.521 0.458,0.198 10 false A85 0.396,1.5 2.281,1.719 1.885,0.219 10 false No. 66 Junction Connector 2.458,1.583 4.292,1.781 1.833,0.198 10 false from Battery 2.313,2.042 4.146,2.24 1.833,0.198 10 false from EFI Relay 2.323,2.5 4.156,2.698 1.833,0.198 10 false from IG2 Relay 2.438,3.125 4.271,3.323 1.833,0.198 10 false to EFI Relay 3.823,1.469 5.052,1.667 1.229,0.198 10 false EFI NO.1 3.813,2.385 5.042,2.583 1.229,0.198 10 false IGN NO.1 5.427,0.667 6.042,0.865 0.615,0.198 10 false CANH 5.438,1.281 6.052,1.479 0.615,0.198 10 false CANL 5.438,1.604 6.052,1.802 0.615,0.198 10 false BATT 5.438,2.073 6.052,2.271 0.615,0.198 10 false +B 5.458,2.531 6.073,2.729 0.615,0.198 10 false IGSW 5.458,3.167 6.073,3.365 0.615,0.198 10 false MREL 5.458,3.76 6.073,3.958 0.615,0.198 10 false E02 5.448,4.188 6.063,4.385 0.615,0.198 10 false E01 5.458,4.635 6.073,4.833 0.615,0.198 10 false EC 5.083,0.76 5.542,0.958 0.458,0.198 10 false A53 5.083,1.177 5.542,1.375 0.458,0.198 10 false A53 5.083,1.594 5.542,1.792 0.458,0.198 10 false A55 5.083,2.063 5.542,2.26 0.458,0.198 10 false A55 5.083,2.521 5.542,2.719 0.458,0.198 10 false A55 5.083,3.156 5.542,3.354 0.458,0.198 10 false A55 5.083,3.75 5.542,3.948 0.458,0.198 10 false B73 5.083,4.167 5.542,4.365 0.458,0.198 10 false B73 5.083,4.625 5.542,4.823 0.458,0.198 10 false A55 1.688,1.083 2,1.281 0.313,0.198 10 false 12 1.698,0.646 2.01,0.844 0.313,0.198 10 false 1 5.125,0.552 5.438,0.75 0.313,0.198 10 false 33 5.115,0.99 5.427,1.188 0.313,0.198 10 false 34 5.156,1.406 5.469,1.604 0.313,0.198 10 false 3 5.146,1.854 5.458,2.052 0.313,0.198 10 false 1 5.156,2.323 5.469,2.521 0.313,0.198 10 false 9 5.156,2.969 5.469,3.167 0.313,0.198 10 false 8 5.156,3.563 5.469,3.76 0.313,0.198 10 false 6 5.156,3.979 5.469,4.177 0.313,0.198 10 false 7 5.125,4.427 5.438,4.625 0.313,0.198 10 false 22 5.656,5.073 6.115,5.271 0.458,0.198 10 false ECM

for N04C-WA
C414813E01
5.26,2.969 5.604,3.146 0.344,0.177 10 false E11 5.26,3.281 5.604,3.458 0.344,0.177 10 false E01 5.271,3.552 5.615,3.729 0.344,0.177 10 false E02 5.25,4.208 6.135,4.521 0.885,0.313 10 false ECM 5.021,1.521 5.25,1.74 0.229,0.219 10 false 70 5.281,1.615 5.844,1.854 0.563,0.24 10 false BATT 3.708,1.438 4.594,1.677 0.885,0.24 10 false EFI NO.1 2.333,1.594 3.531,1.792 1.198,0.198 10 false from Battery 5.01,1.979 5.313,2.198 0.302,0.219 10 false 49 5.271,2.073 5.615,2.229 0.344,0.156 10 false +B 3.677,2.385 4.583,2.719 0.906,0.333 10 false IGN NO.1 1.813,2.042 3.219,2.25 1.406,0.208 10 false from ACT PWR relay 5.271,2.542 5.906,2.854 0.635,0.313 10 false IGSW 2.229,2.51 3.313,2.74 1.083,0.229 10 false from IG2 relay 5.052,2.458 5.219,2.635 0.167,0.177 10 false 6 5,2.896 5.219,3.083 0.219,0.188 10 false 60 4.99,3.167 5.24,3.365 0.25,0.198 10 false 12 4.99,3.479 5.208,3.667 0.219,0.188 10 false 36 5.219,4.021 5.563,4.198 0.344,0.177 10 false A115 5.292,0.302 5.854,0.542 0.563,0.24 10 false CANH 5.01,0.531 5.313,0.75 0.302,0.219 10 false 59 5.01,0.208 5.313,0.427 0.302,0.219 10 false 48 5.292,0.604 5.854,0.844 0.563,0.24 10 false CANL 0.146,0.885 0.49,1.063 0.344,0.177 10 false A123 0.135,1.031 2.188,1.417 2.052,0.385 10 false No. 7 CAN Junction Connector 1.594,0.188 1.76,0.365 0.167,0.177 10 false 9 1.594,0.521 1.76,0.698 0.167,0.177 10 false 20 3.677,1.875 4.583,2.208 0.906,0.333 10 false EFI NO.2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
except N04C-WA A
for N04C-WA B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)

B

6.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.
C371321E01
1.469,0.135 1.833,0.365 0.365,0.229 1.458,2.302 1.823,2.531 0.365,0.229 1.469,2.604 1.833,2.833 0.365,0.229 0.833,0.938 1,0.938 1,0.938 1.25,1.073 true 0.865,1.417 1.042,1.417 1.042,1.417 1.26,1.25 true 0.74,3.469 0.906,3.469 0.906,3.469 1.156,3.604 true 0.865,4.115 1.01,4.115 1.01,4.115 1.146,3.792 true 1.896,4.313 2.052,4.313 2.052,4.313 2.052,3.813 true 2.302,4.313 2.146,4.313 2.146,4.313 2.146,3.813 true 1.531,0.167 1.99,0.365 0.458,0.198 10 false A56 1.51,2.344 1.969,2.542 0.458,0.198 10 false A52 1.521,2.646 1.979,2.844 0.458,0.198 10 false A53 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 2.021,0.177 2.333,0.375 0.313,0.198 10 false *A 0.427,0.865 1.042,1.063 0.615,0.198 10 false CANL 0.438,1.344 1.052,1.542 0.615,0.198 10 false CANH 0.177,3.396 0.792,3.594 0.615,0.198 10 false CANH*B 0.292,4.042 0.906,4.24 0.615,0.198 10 false CANL*B 1.313,4.229 1.927,4.427 0.615,0.198 10 false CANH*C 2.385,4.229 3,4.427 0.615,0.198 10 false CANL*C 1.958,2.333 2.271,2.531 0.313,0.198 10 false *B 1.958,2.646 2.271,2.844 0.313,0.198 10 false *C

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for N04C-VQ, N04C-VL
Tester Connection Condition Specified Condition
A56-7 (CANH) - A56-1 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for N04C-UH
Tester Connection Condition Specified Condition
A52-17 (CANH) - A52-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 2TR-FE
Tester Connection Condition Specified Condition
A53-33 (CANH) - A53-34 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*A for N04C-VQ, N04C-VL
*B for N04C-UH
*C for 2TR-FE
*a Front view of wire harness connector
(to ECM)


Result:
Result Proceed to
OK (for N04C-VQ, N04C-VL) A
OK (for N04C-UH) B
OK (for 2TR-FE) C
NG D



A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

D

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Connect the cable to the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

C371342E01
1.021,0.49 1.417,0.74 0.396,0.25 2.969,0.479 3.365,0.729 0.396,0.25 5.135,0.49 5.563,0.74 0.427,0.25 0.458,3.146 0.625,3.146 0.625,3.146 0.802,2.427 true 1.99,3.125 1.833,3.125 1.833,3.125 1.729,2.292 true 3.156,3.104 3.313,3.104 3.313,3.104 3.417,2.604 true 3.385,3.49 3.573,3.49 3.573,3.49 3.74,2.615 true 2.969,1.01 3.094,1.01 3.094,1.01 3.375,2.063 true 4.375,1.031 4.531,1.031 4.531,1.031 4.729,1.833 true 4.438,3.063 4.604,3.063 4.604,3.063 4.771,2.365 true 4.688,3.417 4.854,3.417 4.854,3.417 5.094,2.385 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.083,0.521 1.406,0.719 0.323,0.198 10 false A56 3.042,0.521 3.365,0.719 0.323,0.198 10 false A57 5.188,0.531 5.615,0.719 0.427,0.188 10 false B102 0.063,3.083 0.677,3.281 0.615,0.198 10 false MREL 2.042,3.042 2.656,3.24 0.615,0.198 10 false IGSW 2.76,3.042 3.375,3.24 0.615,0.198 10 false BATT 3.125,3.417 3.74,3.615 0.615,0.198 10 false +B 4.125,2.99 4.74,3.188 0.615,0.198 10 false E01 4.396,3.344 5.01,3.542 0.615,0.198 10 false E02 4.135,0.958 4.75,1.156 0.615,0.198 10 false E1 2.719,0.938 3.333,1.135 0.615,0.198 10 false EC

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A56-24 (IGSW) - Body ground Ignition switch ON 11 to 14 V
A57-23 (BATT) - Body ground Always 11 to 14 V
A57-24 (+B) - Body ground Battery voltage applied to terminal A56-25 (MREL) 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-11 (EC) - Body ground Always Below 1 Ω
B102-1 (E1) - Body ground Always Below 1 Ω
B102-11 (E01) - Body ground Always Below 1 Ω
B102-12 (E02) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for N04C-VQ) A
OK (for N04C-VL) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Connect the cable to the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

C371343E01
0.635,0.271 1.01,0.531 0.375,0.26 2.406,0.271 2.781,0.531 0.375,0.26 4.135,0.281 4.51,0.542 0.375,0.26 5.948,0.281 6.323,0.542 0.375,0.26 0.615,1.24 0.542,0.625 0.542,0.625 0.427,0.625 true 2.146,1.271 2.073,0.74 2.073,0.74 1.938,0.74 true 4.74,1.281 4.813,0.458 4.813,0.458 4.958,0.458 true 4.927,1.281 5.031,0.74 5.031,0.74 5.177,0.74 true 6.76,1.281 6.656,0.688 6.656,0.688 6.531,0.688 true 6.854,1.542 6.688,2.333 6.688,2.333 6.542,2.333 true 3.031,1.531 2.844,2.5 2.844,2.5 2.688,2.5 true 2.708,1.521 2.573,2.24 2.573,2.24 2.438,2.24 true 0.698,0.313 1.156,0.51 0.458,0.198 10 false A52 2.469,0.323 2.927,0.521 0.458,0.198 10 false A54 4.198,0.323 4.656,0.521 0.458,0.198 10 false B59 6.021,0.333 6.479,0.531 0.458,0.198 10 false B60 0.042,0.552 0.656,0.75 0.615,0.198 10 false BATT 0.083,0.052 0.698,0.25 0.615,0.198 10 false *a 1.688,0.667 2.302,0.865 0.615,0.198 10 false +B 2.01,2.167 2.625,2.365 0.615,0.198 10 false MREL 2.271,2.427 2.885,2.625 0.615,0.198 10 false IGSW 5.01,0.375 5.625,0.573 0.615,0.198 10 false E02 5.24,0.656 5.854,0.854 0.615,0.198 10 false E01 6.281,0.615 6.896,0.813 0.615,0.198 10 false E1 6.292,2.26 6.906,2.458 0.615,0.198 10 false EC

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-2 (BATT) - Body ground Always 11 to 14 V
A54-1 (+B) - Body ground Battery voltage applied to terminal A54-13 (MREL) 11 to 14 V
A54-16 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B59-6 (E02) - Body ground Always Below 1 Ω
B59-7 (E01) - Body ground Always Below 1 Ω
B60-7 (E1) - Body ground Always Below 1 Ω
B60-19 (EC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Connect the cable to the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

C394516N01
1.865,0.042 2.281,0.292 0.417,0.25 4.896,0.042 5.313,0.292 0.417,0.25 1.083,0.25 1.25,0.25 1.25,0.25 1.917,0.76 true 0.979,0.802 1.146,0.802 1.146,0.802 1.5,0.854 true 1.073,1.396 1.24,1.396 1.24,1.396 1.615,1.115 true 1.083,1.583 1.25,1.583 1.25,1.583 2,1.25 true 5.667,0.75 6.177,0.583 6.177,0.583 6.344,0.583 true 5.49,0.729 6.167,0.333 6.167,0.333 6.333,0.333 true 0.885,1.188 1.052,1.188 1.052,1.188 1.479,1.052 true 0.667,0.177 1.125,0.375 0.458,0.198 10 false BATT 1.948,0.083 2.406,0.281 0.458,0.198 10 false A55 4.99,0.083 5.448,0.281 0.458,0.198 10 false B73 0.771,0.719 1.229,0.917 0.458,0.198 10 false +B 0.667,1.323 1.125,1.521 0.458,0.198 10 false IGSW 6.396,0.25 6.854,0.448 0.458,0.198 10 false E02 6.396,0.531 6.854,0.729 0.458,0.198 10 false E01 0.823,1.521 1.281,1.719 0.458,0.198 10 false EC 0.083,0.031 0.542,0.229 0.458,0.198 10 false *a 0.49,1.125 0.948,1.323 0.458,0.198 10 false MREL

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-1 (+B) - Body ground Battery voltage applied to terminal A55-8 (MREL) 11 to 14 V
A55-3 (BATT) - Body ground Always 11 to 14 V
A55-9 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-22 (EC) - Body ground Always Below 1 Ω
B73-6 (E02) - Body ground Always Below 1 Ω
B73-7 (E01) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN BRANCH WIRE)
SST
09843-E7010  

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379567N01
1.531,0.167 1.917,0.385 0.385,0.219 2.917,1.75 2.667,1.75 2.667,1.75 1.865,1.417 true 0.875,0.427 1.104,0.427 1.104,0.427 1.802,1.031 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 2.969,1.688 3.385,1.938 0.417,0.25 10 false CANH 0.49,0.365 0.906,0.615 0.417,0.25 10 false CANL 1.698,0.198 2.115,0.448 0.417,0.25 10 false V

Connect the signal check harness to the ECM vehicle side harness.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
A115-48 (CANH) V36 (CANH)
A115-59 (CANL) V16 (CANL)


Text in Illustration
*a Signal Check Harness Connector


c.

Using SST, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V36 (CANH) - V16 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ECM (CANH, CANL)

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
SST
09843-E7010  

a.

Connect the cable to the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C419347N01
1.771,0.125 2.094,0.354 0.323,0.229 5.229,0.146 5.552,0.375 0.323,0.229 3.063,0.521 2.885,0.521 2.885,0.521 2.594,0.854 true 6.385,0.698 6.208,0.698 6.208,0.698 6.031,0.875 true 0.854,0.656 1.031,0.656 1.031,0.656 1.25,0.76 true 1.271,0.323 1.448,0.323 1.448,0.323 1.604,0.833 true 2.896,1.396 2.719,1.396 2.719,1.396 2.594,1.135 true 3.031,0.865 2.854,0.865 2.854,0.865 2.729,1.083 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 3.073,0.802 3.385,1 0.313,0.198 10 false E01 6.427,0.635 6.74,0.833 0.313,0.198 10 false E02 0.656,0.594 0.969,0.792 0.313,0.198 10 false +B 3.104,0.469 3.51,0.656 0.406,0.188 10 false BATT 0.917,0.271 1.365,0.438 0.448,0.167 10 false IGSW 2.958,1.354 3.271,1.552 0.313,0.198 10 false E11 1.917,0.188 2.365,0.354 0.448,0.167 10 false V 5.354,0.198 5.802,0.365 0.448,0.167 10 false V

Text in Illustration
*a Signal Check Harness Connector - -

Standard Resistance:
Tester Connection Condition Specified Condition
V39 (E11) - Body ground Always Below 1 Ω
V40 (E01) - Body ground Always Below 1 Ω
V60 (E02) - Body ground Always Below 1 Ω


NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
A115-6 (IGSW) V13 (IGSW)
A115-12 (E01) V40 (E01)
A115-36 (E02) V60 (E02)
A115-49 (+B) V1 (+B)
A115-70 (BATT) V19 (BATT)
A115-60 (E11) V39 (E11)



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V19 (BATT) - Body ground Always 11 to 14 V
V1 (+B) - Body ground Ignition switch ON 11 to 14 V
V13 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)