Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Check Engine Local Bus Line  


DESCRIPTION

Symptom Trouble Area
·

Resistance between V9-19 (CANP) and V9-30 (CANN) of translate ECU assembly is below 54 Ω, or 70 Ω or more

·

Resistance between V9-19 (CANP) or V9-30 (CANN) of translate ECU assembly and body ground is below 200 Ω

·

Resistance between V9-19 (CANP) or V9-30 (CANN) of translate ECU assembly and +B is below 6 kΩ


·

Local bus main line and branch line

·

Translate ECU assembly

·

No. 1 CAN junction terminal

·

No. 5 CAN junction terminal

·

No. 7 CAN junction connector

·

No. 9 CAN junction connector



WIRING DIAGRAM

C419844E01
0.177,1.75 1.094,1.948 0.917,0.198 10 false A119 0.167,1.896 2.396,2.167 2.229,0.271 10 false No. 5 CAN Junction Terminal 1.115,1.604 2.031,1.802 0.917,0.198 10 false CANL 1.573,1.396 1.885,1.594 0.313,0.198 10 false 2 1.094,0.948 2.01,1.146 0.917,0.198 10 false CANH 1.573,0.938 1.885,1.135 0.313,0.198 10 false 3 3.031,1.385 3.344,1.583 0.313,0.198 10 false 22 3.042,0.979 3.354,1.177 0.313,0.198 10 false 11 3.792,0.958 4.104,1.156 0.313,0.198 10 false 10 3.802,1.385 4.115,1.583 0.313,0.198 10 false 21 5.385,1.396 5.698,1.594 0.313,0.198 10 false 30 5.385,0.969 5.698,1.167 0.313,0.198 10 false 19 5.667,1.083 6.156,1.281 0.49,0.198 10 false CANP 5.677,1.49 6.167,1.688 0.49,0.198 10 false CANN 5.313,1.688 5.802,1.885 0.49,0.198 10 false V9 5.302,1.844 6.396,2.198 1.094,0.354 10 false Translate ECU Assembly 5.281,3.313 5.917,3.542 0.635,0.229 10 false A115 5.271,3.479 5.719,3.75 0.448,0.271 10 false ECM 5.677,3.083 6.167,3.281 0.49,0.198 10 false CANL 5.667,2.667 6.156,2.865 0.49,0.198 10 false CANH 5.406,2.979 5.719,3.177 0.313,0.198 10 false 59 5.406,2.563 5.719,2.76 0.313,0.198 10 false 48 3.813,2.979 4.125,3.177 0.313,0.198 10 false 20 3.813,2.552 4.125,2.75 0.313,0.198 10 false 9 3.031,2.969 3.344,3.167 0.313,0.198 10 false 19 3.094,2.563 3.406,2.76 0.313,0.198 10 false 8 1.333,2.969 1.646,3.167 0.313,0.198 10 false 7 1.333,2.542 1.646,2.74 0.313,0.198 10 false 5 1.344,4.531 1.656,4.729 0.313,0.198 10 false 3 1.344,4.115 1.656,4.313 0.313,0.198 10 false 1 1.344,6.333 1.656,6.531 0.313,0.198 10 false 4 1.344,5.938 1.656,6.135 0.313,0.198 10 false 2 2.74,3.281 3.656,3.479 0.917,0.198 10 false A123 2.719,3.438 4.01,3.865 1.292,0.427 10 false No. 7 CAN Junction Connector 5.49,4.563 5.802,4.76 0.313,0.198 10 false 8 5.49,4.146 5.802,4.344 0.313,0.198 10 false 9 5.302,4.823 5.792,5.021 0.49,0.198 10 false P12 5.302,5 6.792,5.365 1.49,0.365 10 false Emission Control ECU Assembly 5.667,4.656 6.156,4.854 0.49,0.198 10 false CAN- 5.677,4.25 6.167,4.448 0.49,0.198 10 false CAN+ 0.406,6.677 1.323,6.875 0.917,0.198 10 false P16 5.135,6.729 5.625,6.927 0.49,0.198 10 false A117 5.698,6.552 6.188,6.75 0.49,0.198 10 false VGND 5.698,5.917 6.188,6.115 0.49,0.198 10 false VOUT 5.469,6.354 5.781,6.552 0.313,0.198 10 false 2 5.448,5.938 5.76,6.135 0.313,0.198 10 false 3 5.115,6.906 6.99,7.208 1.875,0.302 10 false No. 1 CAN Junction Terminal 0.385,6.854 1.677,7.281 1.292,0.427 10 false No. 9 CAN Junction Connector

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 7 CAN junction connector.

C358918C04
0.156,0.708 0.563,1.01 0.406,0.302 5.125,0.125 5.542,0.396 0.417,0.271 6.219,1.625 6.073,1.625 6.073,1.625 5.906,1.125 true 2.25,0.969 2.469,0.323 2.469,0.323 2.625,0.323 true 2.135,1.021 1.948,0.229 1.948,0.229 1.802,0.229 true 1.979,0.99 1.708,0.375 1.708,0.375 1.594,0.375 true 1.646,1.448 1.76,1.448 1.76,1.448 2,1.188 true 1.823,1.646 1.958,1.646 1.958,1.646 2.104,1.167 true 2.563,1.583 2.396,1.583 2.396,1.583 2.229,1.177 true 5.25,0.677 4.615,0.292 4.615,0.292 4.5,0.292 true 2.396,1 2.74,0.698 2.74,0.698 2.896,0.698 true 2.813,1.396 2.646,1.396 2.646,1.396 2.354,1.146 true 0.167,0.073 0.479,0.271 0.313,0.198 10 false *a 3.875,0.125 4.188,0.323 0.313,0.198 10 false *b 0.208,0.781 0.667,0.979 0.458,0.198 10 false A123 6.292,1.563 6.75,1.76 0.458,0.198 10 false BAT 5.229,0.188 5.688,0.385 0.458,0.198 10 false J45 1.219,0.135 2.135,0.333 0.917,0.198 10 false CANH*d 1.031,0.313 1.948,0.51 0.917,0.198 10 false CANH*c 2.698,0.26 3.615,0.458 0.917,0.198 10 false CANH*e 2.604,1.51 3.521,1.708 0.917,0.198 10 false CANL*e 1.094,1.365 2.01,1.563 0.917,0.198 10 false CANL*c 1.271,1.573 2.188,1.771 0.917,0.198 10 false CANL*d 4.24,0.219 4.698,0.417 0.458,0.198 10 false CG 2.958,0.625 3.875,0.823 0.917,0.198 10 false CANH*f 2.885,1.323 3.802,1.521 0.917,0.198 10 false CANL*f
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to No. 9 CAN Junction Connector *d to ECM
*e to Translate ECU Assembly *f to No. 5 CAN Junction Terminal



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
A123-8 (CANH) - A123-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 9 CAN junction connector
A123-8 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A123-19 (CANL) - J45-16 (BAT)
A123-8 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A123-19 (CANL) - J45-4 (CG)
A123-9 (CANH) - A123-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
A123-9 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A123-20 (CANL) - J45-16 (BAT)
A123-9 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A123-20 (CANL) - J45-4 (CG)
A123-10 (CANH) - A123-21 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Translate ECU assembly
A123-10 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A123-21 (CANL) - J45-16 (BAT)
A123-10 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A123-21 (CANL) - J45-4 (CG)
A123-11 (CANH) - A123-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction terminal
A123-11 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A123-22 (CANL) - J45-16 (BAT)
A123-11 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A123-22 (CANL) - J45-4 (CG)



d.

Reconnect the No. 7 CAN junction connector.


Result:
Result Proceed to
OK A
NG (No. 3 CAN junction terminal main wire) B
NG (ECM branch wire) C
NG (Translate ECU assembly branch wire) D
NG (No. 9 CAN junction connector main wire) E



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

2.CHECK CAN BUS (NO. 5 CAN JUNCTION TERMINAL - NO. 7 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR CAN BUS WIRES (ECM - NO. 7 CAN JUNCTION CONNECTOR)

D

4.CHECK FOR CAN BUS WIRES (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

E

5.CHECK FOR CAN BUS WIRES (NO. 9 CAN JUNCTION CONNECTOR)
2.CHECK CAN BUS (NO. 5 CAN JUNCTION TERMINAL - NO. 7 CAN JUNCTION CONNECTOR)
a.
C251147C21
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.927,0.25 1.448,0.427 0.521,0.177 10 false CANL 0.583,1.125 1.031,1.375 0.448,0.25 10 false CANH 2.5,0.771 2.948,1.021 0.448,0.25 10 false A119 0.531,2.563 0.979,2.813 0.448,0.25 10 false J45 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the No. 3 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A119-3 (CANH) - A119-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A119-3 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A119-2 (CANL) - J45-16 (BAT)
A119-3 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A119-2 (CANL) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 5 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION TERMINAL - NO. 7 CAN JUNCTION CONNECTOR)

3.CHECK FOR CAN BUS WIRES (ECM - NO. 7 CAN JUNCTION CONNECTOR)
SST
09843-E7010  

a.
C379567C05
1.531,0.167 1.917,0.385 0.385,0.219 2.802,1.698 2.635,1.698 2.635,1.698 1.865,1.365 true 2.76,0.521 2.594,0.521 2.594,0.521 1.833,1.042 true 0.844,0.885 0.583,0.583 0.583,0.583 0.417,0.583 true 2.958,1.031 2.792,1.031 2.792,1.031 2.604,1.365 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.698,0.198 2.115,0.448 0.417,0.25 10 false V 2.875,1.625 3.354,1.792 0.479,0.167 10 false CANH 2.833,0.448 3.313,0.615 0.479,0.167 10 false CANL 0.167,0.51 0.646,0.677 0.479,0.167 10 false +B 3,0.958 3.313,1.146 0.313,0.188 10 false E01
*a Signal Check Harness Connector


Connect the signal check harness to the ECM vehicle side harness.

NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
A115-48 (CANH) V36 (CANH)
A115-59 (CANL) V16 (CANL)
A115-49 (+B) V1 (+B)
A115-12 (E01) V40 (E01)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V36 (CANH) - V16 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V36 (CANH) - V1 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V16 (CANL) - V1 (+B)
V36 (CANH) - V40 (E01) Cable disconnected from negative (-) battery terminal 200 Ω or higher
V16 (CANL) - V40 (E01)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (ECM - NO. 7 CAN JUNCTION CONNECTOR)

4.CHECK FOR CAN BUS WIRES (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.
C422590C02
1.438,0.156 1.792,0.406 0.354,0.25 1.51,1.833 1.865,2.083 0.354,0.25 0.688,1.635 0.854,1.635 0.854,1.635 1.375,1.396 true 2.427,3.052 2.26,3.052 2.26,3.052 2.167,2.698 true 0.979,3.125 1.146,3.125 1.146,3.125 1.646,2.396 true 0.719,0.625 0.885,0.625 0.885,0.625 1.354,1.198 true 0.479,0.135 0.792,0.333 0.313,0.198 10 false *a 1.531,0.198 2.365,0.396 0.833,0.198 10 false V9 0.271,1.552 1.104,1.75 0.833,0.198 10 false CANN 2.479,2.99 3.01,3.177 0.531,0.188 10 false BAT 0.708,3.042 1.542,3.24 0.833,0.198 10 false CG 0.302,0.563 1.135,0.76 0.833,0.198 10 false CANP 0.479,1.823 0.792,2.021 0.313,0.198 10 false *b 1.604,1.865 2.438,2.063 0.833,0.198 10 false J45
*a Front view of wire harness connector
(to Translate ECU Assembly)
*b Front view of DLC3


Disconnect the translate ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-19 (CANP) - V9-30 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
V9-19 (CANP) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
V9-30 (CANN) - J45-16 (BAT)
V9-19 (CANP) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
V9-30 (CANN) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE TRANSLATE ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (TRANSLATE ECU ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

5.CHECK FOR CAN BUS WIRES (NO. 9 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 CAN junction connector.

C358915C09
5.125,0.052 5.521,0.323 0.396,0.271 1.563,0.094 1.958,0.365 0.396,0.271 1.875,0.76 2.198,0.417 2.198,0.417 2.365,0.417 true 2.063,0.865 2.417,0.625 2.417,0.625 2.573,0.625 true 5.885,1.51 5.74,1.51 5.74,1.51 5.292,0.813 true 2.271,1.615 2.115,1.615 2.115,1.615 1.844,1.042 true 1.146,0.438 1.292,0.438 1.292,0.438 1.656,0.823 true 0.958,0.656 1.115,0.656 1.115,0.656 1.49,0.854 true 1,1.333 1.167,1.333 1.167,1.333 1.51,1.052 true 6.333,0.875 6.188,0.875 6.188,0.875 5.896,1.094 true 1.635,0.156 2.094,0.354 0.458,0.198 10 false P16 5.219,0.125 5.677,0.323 0.458,0.198 10 false J45 5.958,1.448 6.271,1.646 0.313,0.198 10 false CG 0.458,0.094 0.771,0.292 0.313,0.198 10 false *a 4.042,0.115 4.354,0.313 0.313,0.198 10 false *b 0.615,0.375 1.531,0.573 0.917,0.198 10 false CANH*d 0.406,0.583 1.323,0.781 0.917,0.198 10 false CANH*c 0.438,1.25 1.354,1.448 0.917,0.198 10 false CANH*e 2.344,1.542 3.26,1.74 0.917,0.198 10 false CANL*e 2.646,0.573 3.563,0.771 0.917,0.198 10 false CANL*d 2.427,0.354 3.344,0.552 0.917,0.198 10 false CANL*c 6.417,0.813 6.729,1.01 0.313,0.198 10 false BAT
*a Front view of wire harness connector
(to No. 9 CAN Junction Connector)
*b Front view of DLC3
*c to Emission Control ECU Assembly *d to No. 3 CAN Junction Terminal
*e No. 7 CAN Junction Connector - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
P16-1 (CANH) - P16-3 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Emission control ECU assembly
P16-1 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P16-3 (CANL) - J45-16 (BAT)
P16-1 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P16-3 (CANL) - J45-4 (CG)
P16-2 (CANH) - P16-4 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction terminal
P16-2 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P16-4 (CANL) - J45-16 (BAT)
P16-2 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P16-4 (CANL) - J45-4 (CG)
P16-5 (CANH) - P16-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 7 CAN junction connector
P16-5 (CANH) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
P16-7 (CANL) - J45-16 (BAT)
P16-5 (CANH) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
P16-7 (CANL) - J45-4 (CG)



c.

Reconnect the No. 9 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Emission control ECU assembly branch wire) B
NG (No. 3 CAN junction terminal main wire) C
NG (No. 7 CAN junction connector main wire) D



A

REPLACE NO. 9 CAN JUNCTION CONNECTOR

B

6.CHECK FOR CAN BUS WIRES (EMISSION CONTROL ECU ASSEMBLY - NO. 9 CAN JUNCTION CONNECTOR)

C

7.CHECK CAN BUS (NO. 3 CAN JUNCTION TERMINAL - NO. 9 CAN JUNCTION CONNECTOR)

D

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 CAN JUNCTION CONNECTOR - NO. 7 CAN JUNCTION CONNECTOR)

6.CHECK FOR CAN BUS WIRES (EMISSION CONTROL ECU ASSEMBLY - NO. 9 CAN JUNCTION CONNECTOR)
SST
09843-E7020  

a.
C421149C06
1.542,0.375 1.927,0.594 0.385,0.219 2.563,1.083 2.417,0.667 2.417,0.667 2.583,0.667 true 2.375,1.083 2.177,0.479 2.177,0.479 2.344,0.479 true 2.813,1.604 2.698,2.25 2.698,2.25 2.865,2.25 true 2.344,1.781 2.229,2.427 2.229,2.427 2.396,2.427 true 1.688,0.417 1.844,0.615 0.156,0.198 10 false E 0.104,0.104 0.385,0.302 0.281,0.198 10 false *a 2.635,0.573 3.125,0.781 0.49,0.208 10 false CAN+ 2.406,0.406 2.896,0.615 0.49,0.208 10 false CAN- 2.917,2.177 3.354,2.365 0.438,0.188 10 false BATT 2.448,2.365 2.885,2.552 0.438,0.188 10 false E01
*a Signal Check Harness Connector Terminal


Connect the signal check harness to the emission control ECU assembly vehicle side harness.

NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
P12-9 (CAN+) E9 (CAN+)
P12-8 (CAN-) E8 (CAN-)
P12-30 (BATT) E30 (BATT)
P12-38 (E01) E38 (E01)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E9 (CAN+) - E8 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E9 (CAN+) - E30 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E8 (CAN-) - E30 (BATT)
E9 (CAN+) - E38 (E01) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E8 (CAN-) - E38 (E01)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (EMISSION CONTROL ECU ASSEMBLY - NO. 9 CAN JUNCTION CONNECTOR)

7.CHECK CAN BUS (NO. 3 CAN JUNCTION TERMINAL - NO. 9 CAN JUNCTION CONNECTOR)
a.
C251147C22
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.927,0.25 1.448,0.427 0.521,0.177 10 false VGND 0.583,1.125 1.031,1.375 0.448,0.25 10 false VOUT 2.51,0.771 2.958,1.021 0.448,0.25 10 false A117 0.531,2.563 0.979,2.813 0.448,0.25 10 false J45 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 3 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the No. 3 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A117-3 (VOUT) - A117-2 (VGND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A117-3 (VOUT) - J45-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A117-2 (VGND) - J45-16 (BAT)
A117-3 (VOUT) - J45-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A117-2 (VGND) - J45-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 CAN JUNCTION TERMINAL - NO. 9 CAN JUNCTION CONNECTOR)