Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Open in Bus 5 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 5 main lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Detection Item Trouble Area

*1: for LHD

*2: for RHD

Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main wire or connector

·

Central gateway ECU (network gateway ECU)

·

Combination meter assembly

·

No. 63 junction connector*1

·

No. 68 junction connector*2



This malfunction is not related to the lines of a bus 5 branch or to ECUs or sensors connected a bus 5 branch.

WIRING DIAGRAM

C371311E08
0.823,0.365 1.438,0.563 0.615,0.198 10 false CA5H 0.865,1.094 1.479,1.292 0.615,0.198 10 false CA5L 5.948,0.385 6.563,0.583 0.615,0.198 10 false CANH 5.958,1.073 6.573,1.271 0.615,0.198 10 false CANL 3.229,0.365 4.458,0.563 1.229,0.198 10 false 1 3.156,0.917 4.385,1.115 1.229,0.198 10 false 12 3.854,0.365 5.083,0.563 1.229,0.198 10 false 2 3.854,0.906 5.083,1.104 1.229,0.198 10 false 13 0.188,1.438 1.417,1.635 1.229,0.198 10 false J51 0.167,1.635 1.688,2.01 1.521,0.375 10 false Central Gateway ECU (Network Gateway ECU) 0.146,2.406 1.375,2.604 1.229,0.198 10 false *1: for LHD 1.219,2.406 2.448,2.604 1.229,0.198 10 false *2: for RHD 2.604,1.385 3.833,1.583 1.229,0.198 10 false J91*1, J76*2 2.594,1.573 4.458,1.927 1.865,0.354 10 false No. 63 Junction Connector*1, No. 68 Junction Connector*2 5.594,1.354 6.823,1.552 1.229,0.198 10 false J1 5.594,1.542 6.771,1.885 1.177,0.344 10 false Combination Meter Assembly 1.313,0.375 1.625,0.573 0.313,0.198 10 false 15 1.323,0.906 1.635,1.104 0.313,0.198 10 false 16 5.708,0.375 6.021,0.573 0.313,0.198 10 false 23 5.719,0.917 6.031,1.115 0.313,0.198 10 false 22

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 63 JUNCTION CONNECTOR)

B

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 68 JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 63 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 63 junction connector.


c.
C358905N13
0.208,0.969 0.573,1.229 0.365,0.26 1.167,1.052 1.167,0.229 1.167,0.229 0.99,0.229 true 1.031,1.052 1.031,0.448 1.031,0.448 0.854,0.448 true 1.031,1.323 1.042,1.76 1.042,1.76 0.865,1.76 true 1.156,1.344 1.156,1.99 1.156,1.99 0.979,1.99 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.281,1.01 0.594,1.208 0.313,0.198 10 false J91 0.313,1.698 0.896,1.885 0.583,0.188 10 false CANL*b 0.427,1.906 1.01,2.094 0.583,0.188 10 false CANL*c 0.302,0.365 0.885,0.552 0.583,0.188 10 false CANH*b 0.458,0.156 1.042,0.344 0.583,0.188 10 false CANH*c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J91-1 (CANH) - J91-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
J91-2 (CANH) - J91-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly


Text in Illustration
*a Front view of wire harness connector
(to No. 63 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Combination Meter Assembly


Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (Combination meter assembly CAN main wire) C



A

REPLACE NO. 63 JUNCTION CONNECTOR

B

3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 63 JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)
a.

Reconnect the J91 No. 63 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C368242E07
1.5,0.406 1.854,0.646 0.354,0.24 1.573,1.302 1.573,1.854 1.573,1.854 1.708,1.854 true 1.469,1.302 1.469,1.854 1.469,1.854 1.313,1.854 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.781,1.771 2.396,1.969 0.615,0.198 10 false CA5L 0.896,1.771 1.51,1.969 0.615,0.198 10 false CA5H 1.573,0.438 2.188,0.635 0.615,0.198 10 false J51

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J51-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 63 JUNCTION CONNECTOR)

4.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 63 JUNCTION CONNECTOR)
a.

Reconnect the J91 No. 63 junction connector.


b.
C358908E04
1.5,0.333 1.865,0.573 0.365,0.24 0.625,1.802 0.771,1.802 0.771,1.802 0.771,1.281 true 1.052,1.802 0.896,1.802 0.896,1.802 0.896,1.281 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.219,1.729 0.833,1.927 0.615,0.198 10 false CANL 1.115,1.719 1.729,1.917 0.615,0.198 10 false CANH 1.604,0.375 1.917,0.573 0.313,0.198 10 false J1

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-23 (CANH) - J1-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 63 JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 68 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 68 junction connector.


c.
C358905N14
0.198,0.938 0.573,1.198 0.375,0.26 1.167,1.844 1.323,1.844 1.323,1.844 1.042,1.313 true 1.052,1.094 1.302,0.365 1.302,0.365 1.156,0.365 true 1.188,1.073 1.438,0.385 1.438,0.385 1.635,0.385 true 1.177,1.302 1.438,1.833 1.438,1.833 1.615,1.833 true 0.271,0.979 0.729,1.177 0.458,0.198 10 false J76 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.677,1.76 2.594,1.958 0.917,0.198 10 false CANL*c 0.667,1.76 1.583,1.958 0.917,0.198 10 false CANL*b 0.583,0.292 1.5,0.49 0.917,0.198 10 false CANH*b 1.677,0.313 2.594,0.51 0.917,0.198 10 false CANH*c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
J76-1 (CANH) - J76-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
J76-2 (CANH) - J76-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly


Text in Illustration
*a Front view of wire harness connector
(to No. 68 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Combination Meter Assembly


Result:
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (Combination meter assembly CAN main wire) C



A

REPLACE NO. 68 JUNCTION CONNECTOR

B

6.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)

C

7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 68 JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)
a.

Reconnect the J76 No. 68 junction connector.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.
C368242E08
1.5,0.406 1.854,0.646 0.354,0.24 1.573,1.302 1.573,1.854 1.573,1.854 1.708,1.854 true 1.469,1.302 1.469,1.854 1.469,1.854 1.313,1.854 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.781,1.771 2.396,1.969 0.615,0.198 10 false CA5L 0.896,1.771 1.51,1.969 0.615,0.198 10 false CA5H 1.573,0.438 2.188,0.635 0.615,0.198 10 false J51

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J51-15 (CA5H) - J51-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 68 JUNCTION CONNECTOR)

7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 68 JUNCTION CONNECTOR)
a.

Reconnect the J76 No. 68 junction connector.


b.
C358908E05
1.5,0.333 1.865,0.573 0.365,0.24 0.625,1.802 0.771,1.802 0.771,1.802 0.771,1.281 true 1.052,1.802 0.896,1.802 0.896,1.802 0.896,1.281 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.219,1.729 0.833,1.927 0.615,0.198 10 false CANL 1.115,1.719 1.729,1.917 0.615,0.198 10 false CANH 1.604,0.375 1.917,0.573 0.313,0.198 10 false J1

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-23 (CANH) - J1-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 68 JUNCTION CONNECTOR)